Digital Projection Highlite 6000dsx User Manual

							Master ID- Displays the ID of the master projector.
Master Status- Shows the status of the master projector.
Connected PJ- Shows the number of slave projectors connected.
Slave Number- Displays the serial number of a slave projector.
Slave ID- Displays the ID of a slave projector.
Slave Status- Displays the status of a slave projector. 
Running - The projector is operating.
Cooling Lamp - The fan is cooling the lamp.
Standby - The projector is in Standby mode.
Communication Error - A communication error has occured.
Connecting... - The projector is verifying the connection.
Error Standby - An error has caused the projector to enter Standby mode.
Page Buttons- Turns ‘pages’ to display information on additional slave projectors.
Reconnect- Confirms connection of all linked projectors.
Five internal Test Patterns are provided to assist with projector setup and alignment.
Use the Red, Green and Blue check boxes to turn individual colours on and off.
C—45
System Operation
Test Pattern
OPERATION
LBV00072; Revision A - 25/09/2001 
						

							Cross Hatch - Used during manufacture to align the DMDs this pattern can be use-
ful in the field for overlaying the images in multiple projector stacks.
Grey Bars- Provides a grey scale for adjusting the projector colour balance away
from that set during manufacture for applications where a custom balance is
required.
Black Raster- Used as the off measurement for calculating the on/off contrast
ratio.
Grey Raster- Gives an indication of the on screen luminance level that can be
expected when displaying video.
White Raster- Used for measuring projector luminance and for on reading for
on/off contrast ratio measurement.
System Operation
OPERATION
LBV00072; Revision A - 25/09/2001 
						

							Screen Illuminance.......................................................... D—1
DMD™ Operation and Usage .......................................... D—2
Multiple Projection ........................................................... D—4
Connection Instructions  .............................................. D—4
Setting up for Double or Triple Stacking  ..................... D—6
External Hardwired Control via Remote 1 Connector .. D—11
Projector Dimensions ..................................................... D—12
Technical Specification ................................................. D—13
Advanced User Information
Section D: Advanced User Information
ADVANCED
LBV00072; Revision A - 25/09/2001 
						

							Advanced User Information
ADVANCED
LBV00072; Revision A - 25/09/2001 
						

							The projectors arc lamp emits a luminous fluxmeasured in lumens. This flux is
directed at the screen and illuminates it, the illuminance(E) can be measured in Lux
(lumens/m2) or Foot Candles (lumens/ft
2). The illuminanceof the screen is 
calculated by dividing the incident flux by the illuminated screen area.
The brightness of the screen, known as the screen luminance(B) is determined by
the amount of light reflected from it (or transmitted through it if using a rear 
projection screen). If the screen is diffuse, the incident light is reflected into a 
hemisphere. If the screen has a reflectivity(R), the screen luminancein candela/m
2
is given by (R x E) / ¹, where E is measured in Lux. If E is measured in Foot-
Candles, the screen luminanceis in Foot-Lamberts, and is given by R x E.
Examples:
1) A 6 x 4 6 diffuse screen, with a reflectivity of 0.8 is illuminated by a projector
emitting 3000 lumens.
The screen illuminance (E) = F / A = 3000 / 27 = 111 Foot-Candles
The screen luminance (B) = R x E = 0.8 x 111 = 89 Foot Lamberts
2) A 4m x 3m screen with a reflectivity of 0.85 is illuminated by a projector 
emitting 3500 lumens.
The screen illuminance (E) = F / A = 3500 / 12 = 292 Lux
The screen luminance (B) = (R x E) / ¹= (0.85 x 292) / ¹= 79 Candela/m2
D—1
Advanced User Information
Screen Illuminance
ADVANCED
LBV00072; Revision A - 25/09/2001 
						

							A DMD™ (Digital Micromirror Device™) is a true digital light modulator and
utilises 786,432 (gv) or 1,310,720 (sx) moving aluminium mirrors, with each one
representing a pixel in the final projected image. Each mirror is suspended over
address electrodes by a torsion hinge between two posts. Depending on the voltage
polarity applied, each mirror will either tilt to left or to the right. When light is
applied to the complete DMD™, only the light redirected from a mirror tilting to
the left is projected.
The projector optically filters white light from the lamp into its constituent red,
green and blue. Each colour illuminates a separate DMD™ whose modulated output
is then recombined with the other two to form the projected full colour image.
DMD & Digital Micromirror Device are trademarks of Texas Instruments Incorporated.
D—2
Advanced User Information
DMD™Operation and Usage
ADVANCED
LBV00072; Revision A - 25/09/2001
Projection Lens
Illumination
(Lamp)
Offset Address  Electrode Support Posts
Torsion Hinge
Flat
Left Tilt
Right Tilt Left
Tilt
Right
Tilt
Mirror Element
Light
Dump
Projector
Lamp
RGBRGBRGBFull Colour Image
Displayed on Screen Projector
Lens Optical Filtering of White Light
into Red, Green and Blue Light
White Light
Green
LightRed
Light Blue
LightWhite Light
DMDs™ 
						

							The mirrors in the DMD™ are arranged in a 1024 x 768 (gv) or 1280 x 1024 (sx)
array allowing images of all aspect ratios to be displayed. However, the proportion
of DMD™ effectively used will differ depending on the aspect ratio of the image
e.g. a 5 x 4 aspect ratio on a 5100gv would only require the use of 960 x 768 mir-
rors. The diagrams below show the DMD™ usage for each aspect ratio (4 x 3, 5 x 4,
8 x 5, 14 x 9 and 16 x 9) with the shaded areas representing redundant mirrors.
D—3
Advanced User Information
ADVANCED
LBV00072; Revision A - 25/09/2001
4 x 3 Aspect Ratio
gv=1024 x 768 Mirrors used
sx = 1280 x 960 Mirrors used
14 x 9 Aspect Ratio
gv = 1024 x 658 Mirrors used
sx = 1280 x 823 Mirrors used
5 x 4 Aspect Ratio
gv = 960 x 768 Mirrors used
sx = 1280 x 1024 Mirrors used
16 x 9 Aspect Ratio
gv = 1024 x 576 Mirrors used
sx = 1280 x 720 Mirrors used
8 x 5 Aspect Ratio
gv = 1024 x 640 Mirrors used
sx = 1280 x 800 Mirrors used
DMD™ Size
gv=1024 x 768 Mirrors
sx=1280 x 1024 Mirrors 
						

							Up to three HIGHlite Displays projectors can be stacked without any additional 
framing (gravity stacking). One unit can be stacked on top of the other up to three
units. Make sure that each foot is securely seated on the stacking pad.
Connection Instructions
To connect multiple projectors use the supplied DVI-D cable to connect the RGB 
DIGITAL output (INPUT 9) of the master projector to the RGB DIGITAL input of
the slave projector (the second and third stack) until all the projectors are connected.
D—4
Advanced User Information
Multiple Projection
ADVANCED
LBV00072; Revision A - 25/09/2001 
						

							Next, using a commercially available, bi-directional RS-232C cable connect the
OPTION OUT terminal of the master projector to the OPTION IN terminal of the
slave projector(s) until all the projectors are connected.
OPTICAL AND MECHANICAL ADJUSTMENT
Place the projectors at the proper height for best screen to projector relationship and
ensure that all projectors have the same display orientation. Next, turn on all the
projectors and display the internal crosshatch test pattern using a different single
colour for each projector e.g. turn on green for the master projector, red for the first
slave projector and blue of the other second slave projector.
D—5
Advanced User Information
ADVANCED
LBV00072; Revision A - 25/09/2001
OUTPUTRGBDIGITAL
INPUT9OUTPUTRGBDIGITAL
INPUT9OUTPUTRGBDIGITAL
INPUT9
OPTIONIN
OUTOPTIONIN
OUTOPTIONIN
OUT
MasterSlaveSlave
DVI-D Cable (1 supplied)
Bi Directional RS232C Cable (not supplied) 
						

							Setting up for Double or Triple Stacking
Adjust the lens shift, zoom and focus to clearly display all projected patterns.
If the vertical alignment of the projector(s) is incorrect, adjust the height of the
feet. If there is any keystone distortion, use Keystone adjustment to correct and
save the settings on each projector.
SIGNAL DATA PREPARATION
When stacking multiple projectors each projector should be configured to display
the input image in exactly the same manner. This requires configuring the master 
projector for each input signal type, adjusting the image and copying it to the slave
projectors using a PC card as follows:
1. Choose one projector to be the master projector and turn it on.
2. Display all the desired input signals adjusting each signal to provide an optimum 
image and place the master projector in standby mode.
3. Remove the PC Card slot decorative panel and insert a PC card into the slot.
4. Press and hold CANCEL, then press POWER on the rear panel of the master 
projector. The POWER indicator will change to steady green and the PC Card 
Access indicator will start flashing. The data will be automatically stored on the 
PC card and the POWER indicator will change to amber.
5. Remove the PC card from the slot of the master projector. With the slave 
projector in standby, insert the PC card into the slot of a slave projector.
Since data in the slave projectors will be lost at this time, make backup copies of
them before proceeding.
6. Press and hold ENTER, then press MENU on the rear panel of the slave 
projector. The POWER indicator will change to steady green and the PC Card 
D—6
Advanced User Information
ADVANCED
LBV00072; Revision A - 25/09/2001
-
-