Digital Projection Highlite 6000dsx User Manual

Packaging........................................................................ A—1
Projector Packaging.................................................... A—1
Lens Packaging........................................................... A—1
Safety Advice................................................................... A—2
Fire and Shock Precautions......................................... A—2
Lamp Precautions....................................................... A—2
Power Supply...

Overview
OVERVIEW
LBV00072; Revision A - 25/09/2001 

Projector Packaging
The following components should be contained within the projector packaging.
Should any of the components be absent, please contact the dealer who supplied the
projector, or Digital Projection Limited (Digital Projection Inc. if in North
America) immediately.
1 x HIGHlite DisplaysProjector
1 x Remote Control Unit with Remote Cable (wireless/wired)
1 x AC Power Cable
1 x AC Power Cable Stopper
1 x DVI-D Cable
2 x AAA Batteries
1 x User Manual
1 x Foam Dust Cap
CompactFlash Memory Card...

The safety instructions provided in this manual are to ensure the long life of your
projector and to prevent fire and shock. Please read them carefully and heed all
warnings.
Fire and Shock Precautions 
Ensure that there is sufficient ventilation and that vents are unobstructed to prevent
potentially dangerous concentrations of ozone and the build-up of heat inside your
projector. Allow at least 20cm (8”) of space between your projector and a wall.
Allow at least 50cm (20”) of space between the...

gas, and will not cause harm if kept out of your eyes. If your eyes have been
exposed to this gas, please flush your eyes out with water immediately and seek
immediate medical attention. Do not rub your eyes as this could cause 
serious injury.
WARNING: Do not look into the lens while the projector is on. Serious damage to
your eyes could result.
CAUTION: The high pressure lamp may explode if improperly handled. Refer all
servicing to qualified service personnel.
Power Supply
The projector is designed to...

Installation Advice
The projector should be placed on a flat, level surface and in a dry area free from
dust and moisture. Do not place the projector in direct sunlight, near heaters or heat
radiating appliances as exposure to direct sunlight, smoke or steam could harm 
internal components.
The projector should always be handled with care. Dropping or jarring the projector
could damage internal components.
Do not place heavy objects on the projector.
If you wish to have the projector installed on the...

Part Names
A—5
0verview
Components
OVERVIEW
LBV00072; Revision A - 25/09/2001
Stacking Pad
Digital Input Terminal Panel
Remote Sensor
PC Card Slot
Lens (optional)
Input Terminal Panel
Ventilation (In)
FootRelease LeverVentilation (Out)Carrying Handle
Ventilation (In)
Ventilation (In) Controls Ventilation (In)AC Input Power Switch 

Control Panel
The control panel at the rear of the projector provides all the main controls 
necessary to operate the projector.
1 - Power Button
Press to turn the projector on when the projector is in the standby condition (Main
Power switch must be on and the POWER indicator lit amber). Press and hold for 2
seconds to turn off the projector.
2 - Power LED
The power indicator is a dual colour LED. When the projector is on the indicator is
green. When the projector is in standby mode the indicator is...

5 - Enter Button
Executes your menu selection and activates items selected from the menu. When the
slidebar or dialog box is displayed: Pressing this button confirms adjustments/
setting and returns to the previous menu display.
6 - Cancel Button
Press this button to exit the menu. Press this button to return the adjustments to the
last condition while you are in the adjustment or setting menu.
7 - Select Cursor Buttons
The up & down cursor buttons are used to select the menu of the item you wish to...

Terminal Panel
The Terminal Panel located at the front of the projector provides all the required
connections for video, computer and remote control.
1 - INPUT 3 (RGB3)
A Mini D-Sub 15 pin connector to allow connection of a PC or other analogue RGB
equipment such as a high-definition document camera.
2 - OPTION IN/OUT
Two Mini D-Sub 9 pin connectors for system expansion such as PC-control. The IN 
A—8
Overview
OVERVIEW
LBV00072; Revision A - 25/09/2001
INPUT3
4
INPUT1
INPUT2 INPUT4
INPUT5
INPUT6
INPUT7...