Digital Projection Highlite 4000dsx User Manual

connection should be attached to the external control equipment such as PC. The
OUT connection provides for daisy-chaining multiple projectors and operating them
with the same external equipment. To daisy-chain projectors, connect the IN termi-
nal of the second projector to the OUT connection of the first projector. A third pro-
jector would be connected to the second projector in the same manner and the pro-
cedure would be repeated until all the projectors are connected.
3 - REMOTE 1
This Mini D-Sub...

8 - INPUT 6 (VIDEO 2)
RCA composite video connection for external equipment such as a VCR or laser
disk player.
9 - INPUT 7 (S-VIDEO 1)
Two BNC connectors allow for S-Video connection for use with external equipment
such as a VCR or laser disk player that have separate Y and C video outputs.
10 - INPUT 8 (S-VIDEO 2)
Mini-DIN-4pin S-video connection for external equipment such as a VCR. This
input allows switching between S2 and S1 VIDEO input modes. See the S-Video
Mode Select section for more...

11 - INPUT 9 (RGB (Digital))
DVI-D 24 pin connectors for double or triple stacking. Use the supplied DVI-D
cable to connect the OUTPUT terminal of the first projector to the second projec-
tors INPUT until all the projectors are connected.
The DVI-D cable must not exceed 5 m (16.4 feet) in length.
These connectors can also be used to accept TMDS standard digital signal output
from a digital ready computer. When used in this manner some 
graphics cards may cause flickering noise on the screen. 
The...

OPTIONALLY AVAILABLE SDI BOARDS
SDI Board (all models)
This board accepts the input of non-compressed signal sources from equipment such
as commercial type digital VCR compatible with digital serial component signals of
the SMPTE 259-C standard and provides a high quality image without quantisation
noise.
BNC cable used with the SDI connector should be Belden 8281 cable, or 3C-2V
equivalent cable or better.
Included in option:-
SDI Board Shield Case
Connector Cable (Internal) Installation Manual
HDSDI...

Remote Control
All the functions of your HIGHlite Displaysprojector can be controlled using the
remote control.  The remote control unit can operate either by infra red or by direct
connection to the projector via a hard wire connection.
For infra red operation the remote control requires to be powered by 2 AAA
(HP16/RO3/LR03) alkaline batteries. The battery compartment is located on the
back of the remote control. To remove the compartment cover press and open as
shown below.
Insert the first battery...

A—14
Overview
OVERVIEW
LBV00072; Revision A - 25/09/2001 

Installation Guidelines...................................................... B—1
Screen Requirements................................................... B
—1
Positioning the Projector  .............................................. B
—4
Installation ....................................................................... B—7
Attaching the Power Cable Stopper ........................... B—7
Lens Installation .......................................................... B—8
Setting Up the Projector...

System Installation
INSTALLATION
LBV00072; Revision A - 25/09/2001 

This installation section explains how to install the projector for optimum results.
To do this, it is necessary to determine the following:
1. The type of screen and whether front or rear projection is to be used.
2. The projector location and therefore the type of lens to be used.
3. The method of mounting for the projector.
4. The type of input source to be used with the projector.
Screen Requirements
As virtually all commercially available screens will give a pleasing image you
should choose...

For optimum viewing, the screen should be a flat surface perpendicular to the floor.
The bottom of the screen should be 1.2m (4 feet) above the floor and the front row
of the audience should not have to look up more than 30° to see the top of the
screen (see opposite).
The distance between the front row of the audience and the screen should be at least
twice the screen height and the distance between the back row and the screen should
be a maximum of 8 times the screen height. The screen viewing area...