Denon D M51dvs Operating Instructions

ENGLISH
31
Speaker
2CH Virtual & SW
Set the screen size and the speaker system.
TV Aspect
4:3 PS
LINE-1 LINE-2 REC OUT MD TAPE ON
Function Setting
Set the LINE-1 and LINE-2 function names and turn the
analog recording output (REC OUT) on or off.
3STATUS
RETURN ANGLE AUDIO
SUB TITLE
SETUP TONE / SDB
ENTER
MUTING
DISPLAY MENU
TOP MENU
SURROUND
PARAMETERCH SELECT
-+VCR CH
\b
6-
10SETTING UP THE SYSTEM
• Once all connections with other AV components have been completed as described in “CONNECTIONS” (see...

ENGLISH
32
(2) Quick setup procedure
•Refer to “Connections” (pages 10 to 17) and check that all the connections are correct.
1
Turn on the power.
•The power indicator (LED) lights green, the power turns on
and the display lights.
ON / STANDBY
ON
Several seconds are required from the time the power button is
pressed until the power turns on. This is due to the built-in muting
circuit that turns off (mutes) the sound when the power is turned
on and off. The power indicator flashes green while the muting...

ENGLISH
33
4
Press the ENTER button to display the
menu’s setting screen.
On the setting screen, the selected item is displayed in yellow and the
values of the other items are
displayed in green.
ENTER
Remote control unit
[1] TV screen size setting
QUICK  SETUP  MENU
SELECT  YOUR  TV  SYSTEM 4 : 3   PAN & SCAN
4 : 3   LETTER  BOX
16 : 9  WIDE
4 : 3   TELEVISION
SELECT  THIS  TO  PLAY  WIDE  DVDs
IN  THE  PAN & SCAN  MODE.
(WITH  THE  SIDES  OF  THE  PICTURE
CUT  OFF) DECISION : ENTER  BUTTON
SELECT...

ENGLISH
34
(3) Detailed system setup (changing the system settings)
•The quick system settings and original settings set upon shipment from the factory are changed using the system setting changing menu. The
settings are stored in the memory until they are changed the next time, \
and remain valid even when the power is turned off.
[1] Speaker settings (type of speaker and whether or not the speaker is con\
nected)
• The output component of the different channels and properties are adjust\
ed...

ENGLISH
35
NOTE:
•Select the speaker size not by the physical size of the speaker
but by the speaker’ s capacity to reproduce low frequencies of
100 Hz or less. If you do not know, determine the best setting by
comparing the sound when the setting is set to  “Small” and
“Large”, keeping the volume low enough to prevent damage to
the speaker.
NOTE:
• Select  “Large” or “Small” not according to the actual size of the
speaker but according to the speaker’ s capacity for playing low
frequency (approximately...

ENGLISH
36
[2] Delay time (distance setting)
•Input the distances from the listening position and the various speakers\
 to set the surround delay time.
• Upon shipment from the factory default the delay time is set to the defa\
ult values in step 3 below.
Preparation:
Measure the distance from the listening position to the various speakers\
.
FRFL
Subwoofer
L1: Distance between subwoofer and listening position
L
2: Distance between front speakers and listening position
Listening position
1
2
If you are...

ENGLISH
37
[3] Adjusting the channel level
•Adjust so that the playback levels of the different channels are equal.
• Make this adjustment by listening to the test tones output from the spea\
kers at the listening position.
• By factory default all the levels of all the channels are set to 0 dB.
• This adjustment can also be made directly from the remote control unit. \
(CH SELECT Button)
1If you are not at the system setting changing menu screen,
read step 1 and 2 on page 34.
2At the system setting...

ENGLISH
38
7
Press the ENTER button to enter the
settings.
•The next screen in the system setting
changing menu appears.
ENTER
Remote control unit
To cancel the settings after the adjustments have been made
Display the channel level adjustment screen, then use the 
•, 
\f , 
0
and 1cursor buttons to select “Level Clear” and select “Ye s ”.
The level settings for all the speakers are set to 0 dB.
NOTE:
When the channel levels are adjusted at the channel level settings,
the adjusted values are applied to...

ENGLISH
39
4
Press the ENTER button to enter the
settings.
•The next screen in the system setting
changing menu appears.
ENTER
Remote control unit
Input function settings
•LINE-1 and LINE-2 can be set as described below.
LINE-1 : “MD” , “CD-R” , “MD/CD-R”  or “AUX” can be
selected.
(“MD/CD-R” can only be set when a system MD
recorder, cassette deck and CD recorder are all
connected and system operations are being used.)
LINE-2 : This can be set to “TAPE”,  “MD”, “AUX” or “D.AUX”.
(Set  “D.AUX”  to use...

ENGLISH
40
2Set discs in the disc tray with the labeled (printed) side facing up.
8 cm disc guideDisc tray
NOTE:
•Do not move the this unit while a disc is playing. Doing so
may scratch the disc.
(1) Opening and Closing the Disc Tray
q Turn on the power.
w Press the OPEN/CLOSE button.
Disc tray
OPEN/CLOSE button
NOTES:
•
Even when the power is in the standby mode, when the
OPEN/CLOSE button is pressed, the ADV-M51 ’s power turns
on and the disc tray operates. (Auto power on function)
• Even if the...