Dell Sx2210 Users Guide

Environmental  Characteristics  
  
Maintenance Guidelines  
Cleaning Your Monitor  
For best practices, follow the instructions in the list below while unpacking, cleaning, or handling your monitor:  
l To clean your antistatic screen, lightly dampen a soft, clean cloth with water. If possible, use a special screen - cleaning tissue or solution suitable for the 
antistatic coating. Do not use benzene, thinner, ammonia, abrasive cleaners, or compressed air.   
l Use a lightly - dampened, warm cloth to...

Back to Contents Page    
 
Appendix   
SX2210  Flat Panel Monitor Users Guide  
  Safety Instructions  
  FCC Notice (U.S. Only) and Other Regulatory Information   
  Contacting Dell  
    
CAUTION: Safety Instructions  
For information on safety instructions, see the safety information that shipped with your monitor.  
FCC Notices (U.S. Only) and Other Regulatory Information  
For FCC notices and other regulatory information, see the regulatory compliance website located at  www.dell.com...

Back to Contents Page    
Setting Up Your Monitor   
 
 
1. Go to  http://support.dell.com ,  enter your service tag, and download the latest driver for your graphics card.   
2. After installing the drivers for your graphics Adapter, attempt to set the resolution to  1920 X 1080  again.  
Back to Contents Page  NOTE:  If you are unable to set the resolution to 1920 x 1080, please contact Dell™ to inquire about a graphics Adapter that supports these resolutions.    

Back to Contents Page    
Setting Up Your Monitor   
SX2210  Flat Panel Monitor  
 
1. Right - click on the desktop and click  Properties .  
2. Select the  Settings  tab.  
3. Select  Advanced .  
4. Identify your graphics controller supplier from the description at the top of the window (e.g. NVIDIA, ATI, Intel etc.).   
5. Refer to the graphic card provider website for updated driver (for example,  http://www.ATI.com  OR  http://www.NVIDIA.com  ).  
6. After installing the drivers for your graphics...

Back to Contents Page    
Operating the Monitor   
SX2210  Flat Panel Monitor Users Guide  
   Turn On the Monitor  
   Using the Front Panel Controls  
   Using the On - Screen Display (OSD) Menu  
   Setting the Maximum Resolution  
   Using the Dell Soundbar (Optional)  
   Using the Tilt  
   Using the Camera   
   Installing and Using the Facial Recognition Software (FastAccess)  
    
Turn On the Monitor  
Press the    button to turn on the monitor  
           
   
Using the Front Panel Controls...

Front panel button  
Use the buttons  on the side of the monitor to adjust the image settings.   
               
   
Using the On - Screen Display (OSD) Menu  
 
Accessing the Menu System  Exit Use the Exit  button  to exit on - screen display (OSD) from menu and sub - menus.  
Front panel Button Description  
A  
Up  Use the Up button to adjust (increase ranges) items in the OSD menu.
B  
Down  Use the Down button to adjust (decrease ranges) items in the OSD menu.
C   
OK    
Use the OK button to...

The table below provides a list of all the OSD menu options and their functions.   
2.  
Press the   and   buttons to toggle between options in the Menu. As you move from one icon to another, the option name is highlighted.   
3.  
To select the highlighted item on the menu press the   again.   
4.  
Press the   and   buttons to select the desired parameter.   
5.  
Press the   buttons to enter the slide bar and then use the   or   button, according to the indicators on the menu, to make your changes....

   
 
 
    Auto Adjustment allows the monitor to self - adjust to the incoming video signal. After using Auto Adjustment, you can further tune 
your monitor by using the Pixel Clock (Coarse) and Phase (Fine) controls under Image Settings.  
 
    NOTE:   Auto Adjust does not occur if you press the button  while there are no active video input signals or attached cables .  
  Input Source   Use the Input Source menu to select different video signals that may be connected to your monitor....

 
Back  
Press the   button   to go back to the main menu.  
    Input Color Format   Allows you to set the video input mode to:   
l RGB : Select this option if your monitor is connected to a computer or DVD player using the HDMI cable or the HDMI to DVI 
adapter.   
l YPbPr : Select this option if your DVD player supports only YPbPr output.   
 
Mode Selection   Allows you to set the display mode to:   
l Graphics : Select this mode if your monitor is connected to your computer.   
l Video : Select...

 
Display setting mode 
submenu   
   
 
 
Back  
Press the   button   to go back to the main menu.  
    Horizontal  position  
Use the   and   buttons   to adjust image left and right (min 0 ~ max 100).   
NOTE:   When using DVI or HDMI source, the Horizontal Position setting is not available.   
    Vertical Position  
Use the   and   buttons   to adjust image up and down (min 0 ~ max 100).   
NOTE:   When using DVI or HDMI source, the Vertical Position setting is not available.   
    Pixel Clock   T...