Dell S199wfp Users Guide

							Product Specific Problems  
Troubleshooting Your Soundbar  
Back to Contents Page  SPECIFIC SYMPTOMS WHAT YOU EXPERIENCE POSSIBLE SOLUTIONS
Screen image is too small Image is centered on screen, but does not fill 
entire viewing area. l Perform monitor reset on All Settings.   
Cannot adjust the monitor with the 
buttons on the front panel OSD does not appear on the screen. l Turn off the monitor, unplug the power cord and then 
plug back and turn on the monitor.   
COMMON 
SYMPTOMS   WHAT YOU EXPERIENCE   POSSIBLE SOLUTIONS  
No Sound No power to Soundbar  -  the 
power indicator is off.   
(built - in DC power supply. i.e. 
1905FP ) l Turn the Power/Volume knob on the Soundbar clockwise to the middle position; check if the 
power indicator (green LED) on the front of the Soundbar is illuminated.   
l Confirm that the power cable from the Soundbar is plugged into the monitor.   
l Confirm that the monitor has power.   
l If the monitor has no power, see  Troubleshooting your monitor  for monitor common problem.   
No Sound Soundbar has power  -  power 
indicator is on. l Plug the audio line - in cable into the computers audio out jack.   
l Set all Windows volume controls to their maximum.   
l Play some audio content on the computer (i.e. audio CD, or MP3).   
l Turn the Power/Volume knob on the Soundbar clockwise to a higher volume setting.   
l Clean and reseat the audio line - in plug.   
l Test the Soundbar using another audio source (i.e. portable CD player).   
Distorted Sound Computers sound card is used 
as the audio source. l Clear any obstructions between the Soundbar and the user.   
l Confirm that the audio line - in plug is completely inserted into the jack of the sound card.   
l Set all Windows volume controls to their midpoints.   
l Decrease the volume of the audio application.   
l Turn the Power/Volume knob on the Soundbar counter - clockwise to a lower volume setting.   
l Clean and reseat the audio line - in plug.   
l Troubleshoot the computers sound card.   
l Test the Soundbar using another audio source (i.e. portable CD player).   
Distorted Sound Other audio source is used. l Clear any obstructions between the Soundbar and the user.   
l Confirm that the audio line - in plug is completely inserted into the jack of the audio source.   
l Decrease the volume of the audio source.   
l Turn the Power/Volume knob on the Soundbar counter - clockwise to a lower volume setting.   
l Clean and reseat the audio line - in plug.   
Unbalanced Sound 
Output Sound from only one side of 
Soundbar l Clear any obstructions between the Soundbar and the user.   
l Confirm that the audio line - in plug is completely inserted into the jack of the sound card or 
audio source.   
l Set all Windows audio balance controls (L - R) to their midpoints.   
l Clean and reseat the audio line - in plug.   
l Troubleshoot the computers sound card.   
l Test the Soundbar using another audio source (i.e. portable CD player).   
Low Volume Volume is too low. l Clear any obstructions between the Soundbar and the user.   
l Turn the Power/Volume knob on the Soundbar clockwise to the maximum volume setting.   
l Set all Windows volume controls to their maximum.   
l Increase the volume of the audio application.   
l Test the Soundbar using another audio source (i.e. portable CD player).     
						

							Back to Contents Page    
 
Using Your Monitor Stand   
 
   Attaching the Stand  
   Organizing Your Cables  
   Using the Tilt  
   Removing the Stand    
Attaching the Stand  
 
To attach the stand:  
1. Place the stand on a flat surface.  
2. Fit the groove on the back of the monitor onto the two tabs on the stand.  
3. Lower the monitor so that the monitor mounting area snaps on/locks to the stand.  
Organizing Your Cables  
 
 
After attaching all necessary cables to your monitor and computer, (See  Connecting Your Monitor  for cable attachment,) use the cable holder to neatly 
organize all cables as shown above.   
Using the Tilt  
You can tilt the monitor to best fit your viewing needs.   NOTE:  The stand is detached when the monitor is shipped from the factory.  
						

							Removing the Stand  
 
1.Place the monitor on a stable flat table.  
2. Lift the stand away from the monitor while pressing the stand release button.   
Back to Contents Page  
     
   After placing  the monitor panel on soft cloth or cushion, complete the following steps to remove the stand.