Dell S199wfp Users Guide

							 
Notes, Notices, and Cautions  
   
   
   
   
Information in this document is subject to change without notice.  
 
Reproduction in any manner whatsoever without the written permission of Dell Inc.   is strictly forbidden.  
Trademarks used in this text:  Dell , the  DELL  logo,  Inspiron ,  Dell Precision ,  Dimension ,  OptiPlex ,  Latitude, PowerEdge, PowerVault, PowerApp, and Dell OpenManage  are trademarks of Dell 
Inc;  Microsoft, Windows, and Windows NT are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. which may be 
registered in certain jurisdictions.  is a registered trademark of the U.S. Environmental Protection Agency. As an ENERGY STAR partner, Dell Inc. has determined that 
this product meets the ENERGY STAR guidelines for energy efficiency.  
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any 
proprietary interest in trademarks and trade names other than its own.  
Model S199WFP   
August 2007 Rev. A00  About Your Monitor  
Front View  
Back View  
Side View  
Bottom View  
Monitor Specifications  
Caring for your Monitor  
Using Your Monitor Stand  
Attaching the Stand  
Organizing Your Cables  
Using the Tilt  
Removing the Stand  
Setting Up Your Monitor  
Connecting Your Monitor    
Using the Front Panel  
Using the OSD  
Setting the Optimal Resolution   
Using the Dell Soundbar (Optional)  
    Solving Problems  
Troubleshooting Your Monitor  
General Problems  
Product Specific Problems  
Troubleshooting Your Soundbar  
   
   
Appendix  
FCC Identification Information  
Safety Information  
Contacting Dell  
Your Monitor Setup Guide  
   
NOTE:  A NOTE indicates important information that helps you make better use of your computer. 
NOTICE:  A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. 
  CAUTION:  A CAUTION indicates a potential for property damage, personal injury, or death.  
						

							Back to Contents Page    
About Your Monitor   
 
   Front View  
   Back View  
   Side View  
   Bottom View  
   Monitor Specifications  
    Caring for your Monitor  
Front View  
 
 
Back View  1.   Input signal select  button  
2.   OSD menu / Select button  
3.    Brightness and Contrast / Down ( - ) button  
4.   Auto - adjust / Up (+) button  
5.   Power On / Off button (with LED indicator)  
 
   
1   VESA mounting holes (100mm) (Behind 
attached base plate)   Use to mount the monitor.  
2   Barcode serial number label   Refer to this label if you need to contact Dell for technical support.  
       
						

							Bottom View  
 
Side View  
Monitor Specifications  3   Security lock slot   Use a security lock with the slot to help secure your monitor.  
4   Stand removal button    Press to release the stand .  
5   Regulatory rating label    List the regulatory approvals.   
6   Dell Soundbar mounting brackets   Attach the optional Dell Soundbar.  
7   Cable holder    Help organize cables by placing them through the holder.   
1   Power connector   Insert the power cable.  
2   Dell Soundbar power connector   Connect the power cord for the Soundbar (optional).  
3 Stand anti - theft feature    Mount a 3*8 screw to make the stand undetachable.
4   DVI connector   Connect your computer DVI cable.  
5   VGA connector   Connect your computer VGA cable.  
   
Left side       Right side        
						

							Power Management Modes  
If you have VESA's DPM™ compliance display card or software installed in your PC, the monitor automatically reduces its power consumption when not in use. This is 
referred to as Power Save Mode. The monitor automatically resumes functioning when the system detects input from the keyboard, mouse or other input devices.The 
following table shows the power consumption and signaling of this automatic power saving feature:   
   
Activate the computer and the monitor to gain access to the  OSD .  
* Zero power consumption in OFF mode can only be achieved by disconnecting the main cable from the monitor.  
Pin Assignments  
15 - pin D - Sub connector  
 VESA Modes   Horizontal Sync   Vertical Sync  Video   Power Indicator   Power Consumption  
Normal operation (with Dell Soundbar active)   Active   Active   Active    Blue   75 W (maximum)  
Normal operation   Active   Active   Active    Blue   32 W (typical)  
Active - off mode   Inactive   Inactive   Blanked   Amber   Less than 2 W  
Switch off   -   -   -   Off   Less than 1 W  
  NOTE:  The OSD only functions in the normal operation mode. One of the following messages appears when the Menu or Plus buttons are pressed when in 
Active - off mode.    
   
1 : Auto Detect (Analog Input)  
   
In Power Save Mode  
   
Press computer power button  
   
or any key on keyboard or move mouse  
       
   
or       
1 : Auto Detect (Digital Input)  
   
In Power Save Mode  
   
Press computer power button  
   
or any key on keyboard or move mouse  
   
   
2: Analog Input  
   
In Power Save Mode  
   
Press computer power button  
   
or any key on keyboard or move mouse  
       
   
or       
3: Digital Input  
   
In Power Save Mode  
   
Press computer power button  
   
or any key on keyboard or move mouse  
This monitor is  ENERGY STAR ® - compliant as well as TCO 99 power management compatible.  
 
Pin Number   Monitor Side of the 15 - pin Side Signal Cable  
1   Video - Red  
2   Video - Green  
3   Video - Blue  
4   GND  
5   Self - test   
6   GND - R  
7   GND - G  
8   GND - B  
9   DDC +5V  
     
						

							24 - pin Digital - only DVI Connector  
 
Note: Pin 1 is at the top right.  
Plug and Play Capability  
You can install the monitor in any Plug and Play - compatible system. The monitor automatically provides the computer with its Extended Display Identification Data (EDID) 
using Display Data Channel (DDC) protocols so that the system can configure itself and optimize the monitor settings. Most monitor installations are automatic. You can 
select different settings if required.  10   GND - sync  
11   GND  
12   DDC data  
13   H - sync  
14   V - sync  
15   DDC clock  
Pin   Signal Assignment   Pin   Signal Assignment   Pin   Signal Assignment  
1   T.M.D.S. Data 2 -   9   T.M.D.S. Data 1 -   17   T.M.D.S. Data 0 -  
2   T.M.D.S. Data 2+   10   T.M.D.S. Data 1+   18   T.M.D.S. Data 0+  
3   T.M.D.S. Data 2 Shield   11   T.M.D.S. Data 1 Shield   19   T.M.D.S. Data 0 Shield  
4   No Pin   12   No Pin   20   No Pin  
5   No Pin   13   No Pin    21   No Pin  
6   DDC Clock   14   +5V Power   22   T.M.D.S. Clock Shield  
7   DDC Data   15   Ground (for +5V)   23   T.M.D.S. Clock +  
8   No Connect   16   Hot Plug Detect   24   T.M.D.S. Clock  -  
General      
Model number   S199WFP  
Flat Panel      
Screen type   Active matrix  -   TFT LCD  
Screen dimensions   19 inches wide(19 - inch wide viewable image size)  
Preset display area:  
   
Horizontal  
408 mm / 16.1inches  (minimum)  
Vertical  
255 mm / 10.0 inches  (minimum)  
Pixel pitch   ~ 0.2850mm   
Viewing angle   160° (verticalyfW\S
						

							Resolution  
Horizontal scan range   30 kHz to 83 kHz (automatic)  
Vertical scan range   56 Hz to 75 Hz (automaticyf  
Optimal preset resolution   1440 x 900 at 60 Hz  
Highest preset resolution 1440 x 900 at 75 Hz
Video Display Capabilities (DVI HD Playback)  480i/576i/1080i/480p/576p/720p/1080p(Supports HDCP) 
Preset Display Modes  
The following table lists the preset modes for which Dell guarantees image size and centering:    
    Display Mode   Horizontal Frequency (kHz)   Vertical Frequency (Hz)   Pixel Clock 
(MHz)   Sync Polarity 
(Horizontal/Vertical)  
VESA, 720 x 400   31.5   70.0   28.3   - /+  
VESA, 640 x 480    31.5   60.0   25.2   - / -  
VESA, 640 x 480   37.5   75.0   31.5   - / -  
VESA, 800 x 600   37.9   60.3   49.5   +/+  
VESA, 800 x 600   46.9   75.0   49.5   +/+  
VESA, 1024 x 768   48.4   60.0   65.0   - / -  
VESA, 1024 x 768   60.0   75.0   78.8   +/+  
VESA, 1152 x 864   67.5   75.0   108   +/+  
VESA, 1280 x 1024   64.0   60.0   135.0   +/+  
VESA, 1280 x 1024   80.0   75.0   135.0   +/+  
VESA, 1440 x 900    55.9   60.0   106.5   - /+  
Electrica l  
The following table lists the monitor electrical feature:  
    Video input signals Analog RGB, 0.7 Volts +/ - 5%, positive polarity at 75 ohm input impedance  
Digital DVI - D TMDS, 600mV for each differential line, positive polarity at 50 ohm input impedance
Synchronization input signals Separate horizontal and vertical synchronizations, polarity - free TTL level, SOG (Composite SYNC on 
green)
AC input voltage / frequency / 
current 100 to 240 VAC / 50 or 60 Hz  +  3 Hz / 2.0A (Max.)
Inrush current 120V:30A (Max.)  
240V:60A (Max.) 
Physical  Characteristics  
The following table lists the monitor physical characteristics:   
Connector type 15 - pin D - subminiature, blue connector; DVI - D, white connector
Signal cable type Digital: Detachable, DVI - D, Solid pins, shipped detached from the monitor   
Analog: Detachable, D - Sub, 15pins, shipped attached to the monitor  
Dimensions (with stand)
Height  14.42 inches (366.21 mm)
Width 17.59 inches (446.72 mm)
Depth 5.81 inches (147.65 mm)
Dimensions: (without stand)
Height  11.52 inches (292.5 mm)
Width 17.59 inches (446.72 mm)
Depth 2.32 inches (59.00 mm)  
						

							                  
Caring for your Monitor  
l To clean your antistatic screen, slightly dampen a soft, clean cloth with water. If possible, use a special screen - cleaning tissue or solution suitable for the antistatic 
coating. Do not use benzene, thinner, ammonia, abrasive cleaners, or compressed air.   
l Use a slightly dampened, warm cloth to clean the plastics. Avoid using detergent of any kind as some detergents leave a milky film on the plastics.    
l If you notice a white powder when you unpack your monitor, wipe it off with a cloth. This white powder occurs during the shipping of the monitor.   
l Handle your monitor with care as darker - colored monitor may scratch and show white scuff marks more than lighter - colored monitor.    
l To help maintain the best image quality on your monitor, use a dynamically changing screen saver and power off your monitor when not in use.   
     
Back to Contents Page  Stand dimensions:
Height 11.04 inches (280.31 mm)
Width 10.43 inches (264.84 mm)
Depth 5.81 inches (147.65 mm)
Weight with packaging 15.66lbs (7.1 kg) 
Weight with stand assembly and 
cables 12.79 lbs (5.8 kg) 
Weight without stand assembly  
(For wall mount or VESA mount 
considerations  -  no cables) 8.16 lbs (3.7 kg) 
Weight of stand assembly 2.87 lbs (1.3 kg) 
Environmental  
The following table lists the environmental condition for monitor:  
Temperature
Operating 5° to 35°C (41° to 95°Fyf
Nonoperating Storage:  - 20° to 60°C ( - 4° to 140°Fyf  
Shipping:  - 20° to 60°C( - 4° to 140°Fyf
Humidity
Operating 10% to 80% (noncondensing)
Nonoperating Storage: 5% to 90% (noncondensing)  
Shipping: 5% to 90%(noncondensing)
Altitude  
Operating 3,657.6m (12,000 ft) max
Nonoperating 12,192 m (40,000 ft) max
Thermal dissipation 256.08 BTU/hour (maximum)  
119.5 BTU/hour (typical)
  CAUTION: Read and follow the  safety instructions  
     
						

							Back to Contents Page  
Appendix   
Dell™ S199WFP Flat Panel Monitor User's Guide  
  FCC Notice (U.S. Only)  
  CAUTION: Safety Instruction  
  Contacting Dell  
  Your Monitor Set - up Guide  
FCC Notice (U.S. Only)  
FCC Class B   
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturers instruction manual, may 
cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 
15 of the FCC Rules.   
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:  
1 This device may not cause harmful interference.   
2 This device must accept any interference received, including interference that may cause undesired operations:  
NOTICE:  The FCC regulations provide that changes or modifications not expressly approved by Dell Inc. could void your authority to operate this equipment.   
These limits are designed to provide reasonable protection against harmful interference in a residential installation. However, there is no guarantee that interference will 
not occur in a particular installation. If this equipment does cause harmful interference with radio or television reception, which can be determined by turning the 
equipment off and on, you are encouraged to try to correct the interference by one or more of the following measures:   
l Reorient the receiving antenna.    
l Relocate the system with respect to the receiver.    
l Move the system away from the receiver.    
l Plug the system into a different outlet so that the system and the receiver are on different branch circuits.   
If necessary, consult a representative of Dell Inc. or an experienced radio/television technician for additional suggestions.   
   
The following information is provided on the device or devices covered in this document in compliance with the FCC regulations:  
l Product Name : S199WFP   
l Model number : S199WFP   
l Company Name :    
Dell Inc.   
Worldwide Regulatory Compliance & Environmental Affairs  
One Dell Way Round Rock, TX 78682 USA 512 - 338 - 4400  
CAUTION: Safety Instruction  
For information on safety instructions, see the  Product Information Guide .  
Contacting Dell  
For Customers in the United States, call 800 - WWW - DELL (800 - 999 - 3355)  
   NOTE:  If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog.         
						

							Dell provides several online and telephone - based support and service options. Availability varies by country and product, and more services may not be available in 
your area. To contact Dell for sales, technical support, or customer service issues:  
1. Visit  support.dell.com   
2. Verify your country or region in the  Choose A Country/Region  drop - down menu at the bottom of the page.  
3. Click  Contact Us  on the left side of the page.  
4. Select the appropriate service or support link based on your need.  
5. Choose the method of contacting Dell that is convenient for you.   
Your Monitor Set - up Guide  
To view PDF files (files with an extension of . pdf ), click the document title. To save PDF files (files with an extension of . pdf ) to your hard drive, right - click the 
document title, click  Save Target As  in Microsoft ®  Internet Explorer or  Save Link As  in Netscape Navigator, and then specify a location on your hard drive to 
which you want to save the files.   
Setup Guide  ( .pdf ) (3.32 MB)  
Back to Contents Page   NOTE:  PDF files require Adobe ®  Acrobat ®  Reader ® ,  which can be downloaded from the Adobe website at to view a PDF 
file, launch Acrobat Reader. Then click File - > Open and select the PDF file.     
						

							Back to Contents Page    
 
Setting Up Your Monitor   
 
   Connecting Your Monitor  
   Using the Front Panel  
   Using the OSD Menu  
   Setting the Optimal Resolution  
   Using the Dell Soundbar (Optional)  
Connecting Your Monitor  
 
 
Using the Front Panel  
Use the buttons on the front of the monitor to adjust the image settings.   CAUTION:  Before you begin any of the procedures in this section, follow the  safety instructions .  
or  
1. Turn off your computer and disconnect the power cable. 
2.  Connect either the white DVI or the blue VGA cable to the connectors on the computer and the monitor. 
3. Connect the power cable.
4. Turn on your monitor and computer. If you do not see an image, press the input select button and ensure the correct input source is selected. If you still do not 
see an image, see  Troubleshooting your monitor .