Dell Projector S500/S500wi User Manual

Using Your Projector61
•Rear Projection-Wall Mount — The projector reverses and turns the 
image upside down. You can project from behind a translucent screen with 
a wall-mounted projection. 
•Front Projection-Desktop — This is the default option.
•Front Projection-Wall Mount — The projector turns the image upside 
down for wall-mounted projection.
SPEAKER—Select On to enable the speaker. Select  Off to the disable 
speaker.
CLOSED CAPTION—Select  On to enable close caption and activate the 
closed...

62Using Your Projector
FACTORY RESET—Select and press   to reset all settings to its factory 
default. The below warning message appears:
Reset items include both computer  sources and Video source settings. 
WIRELESS/LAN SETTINGS (IN LAN MODE)—Select and press   to activate 
Wireless/LAN settings. The Wireless/LAN  settings menu provides the following 
options:
Test Pattern 1:
Test Pattern 2: 

Using Your Projector63
WIRELESS/LAN—Select On to activate the Wireless/LAN function. You 
can also set the Wireless/LAN module to on/off while the projector is in the 
standby status.
WIRELESS SETTINGS—Select and press   to activate the Wireless Settings 
menu. See Wireless/LAN Settings (in Wireless Mode) on page 64.
DHCP—If a DHCP server exists in the  network to which the projector is 
connected, the IP address will automatically be acquired when you select 
DHCP On. If DHCP is Off, manually  set the...

64Using Your Projector
4. If you select  Store without pressing the  Enter button, the system will 
keep the original settings.
RESET—Press   to reset network configuration.
WIRELESS/LAN SETTINGS (IN WIRELESS MODE)—Select and press   to activate 
wireless settings. The wireless settings  menu provides the following options:
WIRELESS—Default option is Connected. Select Disconnected  to disable 
the wireless connection.
 
NOTE: It is recommended to use the de fault settings for Wireless 
Connect.
DHCP...

Using Your Projector65
c After the setup is complete, press the   button to exit.
3. After the IP Address, Subnet Ma sk, Gateway, and DNS is set up, 
select  Store and press   button to store the settings.
4. If you select  Store without pressing the  Enter button, the system will 
keep the original settings.
MENU SETTINGS—Select and press   to activate the menu settings. The menu 
settings consists of the following options:
MENU POSITION—Allows you to change the position of the OSD menu on 
the screen....

66Using Your Projector
aGo to  Menu Settings , press   and then select  Pa s s w o r d to Enabled 
the password settings.
b
Enabling the Password function will  pop up a change screen. Key in a 
4-digit number from the screen and press  .
cTo confirm, enter the password again. 
dIf the password verification is succ essful, you may resume with accessing 
the projectors functions and its utilities.
2If you have entered an incorrect password, you will be given another two 
chances. After three invalid...

Using Your Projector67
CHANGE PASSWORD—Key in the original password. Then, enter the new 
password and confirm the new password again.
POWER SETTINGS—Select and press   to activate power settings. The power 
settings menu provides the following options:
S500 Change Password screen S500wi Change Password screen 

68Using Your Projector
QUICK SHUTDOWN—Select On to turn off the projector with a single press of 
the Power button. This function allows the projector to quickly power off 
with an accelerated fan speed. Slightly  higher acoustic noise is expected 
during quick power off.
 
NOTE: Before you turn on the projector  again, wait for 60 seconds to 
allow the internal temperature to  stabilize. The projector will take a 
longer time to turn on if you try  to power on immediately. Its cooling fan 
will run at...

Using Your Projector69
1. Ensure that the Interactive P en is connected. See Connecting With 
Your Interactive Pen (for S500wi only) on page 27.
2. Interactive Pen cannot be used in the following circumstances: a In extend mode.
b When the 3D display function is  enabled, and there is a 120 Hz 
input source connected to the projector.
3. Interactivity is supported only in  the following input modes: VGA and 
HDMI from a Computer, and Wireless  Display, LAN Display, or USB 
Display.
C
HANNEL—Allows you to...

70Using Your Projector
CLICK SPEED—Allows you to set the mouse pause time. This function is 
only available in Normal mode. The available options are: Fast, 
Medium, and Low.
•Fast 
— Set the pointer motion freeze time to the minimum amount 
of time, 0.5 seconds.
•Medium 
— Set the pointer motion freeze time to the middle value, 
1.0 seconds.
•Low 
— Set the pointer motion freeze time to the maximum amount 
of time, 1.5 seconds
S
ET FUNCTION—Allows you to set the function of the Function button 
on the...