Dell Projector 1510X User Manual

Using Your Projector51
Projector Status and Control Page
•Projector Status: There are 5 status: Lamp On, Standby, Power Saving, 
Cooling and Warming up. Click the Refresh button to refresh the status and 
control settings.
•Po w e r  S a v i n g: Power Saving can be set to Off, 30, 60, 90, or 120 minutes. 
Refer to page 43.
•Alert Status: There are 3 error status: Lamp warning, Low lamp life, and 
Temperature warning. Your projector might lock up in protection mode if 
any of the alerts is activated. To...

52Using Your Projector
 - Bright: Maximum brightness and contrast.
 - 
Movie: For viewing movie & photo.
 - 
sRGB: Provide a more accurate color representation.
 - 
Custom: User preferred settings.
•Blank Screen: You can select On or Off.
•Aspect Ratio: Allows you to select the aspect ratio to adjust how the image 
appears.
•Brightness: Select value 
to adjust the brightness of the image.
•Contrast: Select value to adjust the display contrast.
•Audio Input: You can select Audio-A, Audio-B, HDMI and...

Using Your Projector53
E-mail Alert
• E-mail Alert: You can set whether to be notified by email (Enable) or not 
(Disable).
•To/CC/From: You can enter email address of sender (From) and recipients 
(To/Cc) to receive notification when an abnormality or warning occurs.
• Alert Condition: You can select the abnormalities or warnings to be notified 
by email. When any of the alert conditions occur, an email will be sent to 
the recipients (To/Cc).
•Out going SMTP server, User name and Password should be...

54Using Your Projector
Password Setting
Use Password Setting to set up an administrator password to access the We b  
Management. When enabling password for the first time, set the password before 
enabling it. When the password function is enabled, the administrator password 
will be required for accessing the Web Management.
•New Password: Enter new password
•Confirm Password: Enter password again and submit
•Write Community: Set security for SNMP. Enter password and submit.
 
NOTE: Contact Dell if you...

Using Your Projector55
Login Page
•Administrator Password: Enter the Administrator Password and click Login. 

56Using Your Projector
Firmware Update
Use the Firmware Update page to update your projector’s firmware. Press Update 
to start.
• Please wait till the count reaches 0. 

Using Your Projector57
• Wait for 3 seconds and it will proceed to the next step automatically.
• Select the file to upgrade and click the Upgrade button. When upgrading is 
in progress, the Cancel button is disabled. 

58Using Your Projector
• Please wait till the count reaches 0.
• When upgrade is complete, please click the ReLogin button to go back to 
the Web Management Home Page. 

Using Your Projector59
TIPS:
I would like remote access the 
projector via Internet. What is 
the better setting for the 
browser?To have a better setting for the browser, please 
follow the steps below:
1Open Control Panel  Internet Options  
General tab   Te m p o r a r y  I n t e r n e t  F i l e s  
Settings  Select Every visit to the pages.
2Some firewall or anti-virus may block the 
HTTP application, if possible turn off the 
firewall or anti-virus.
I would like to remote access the 
projector via...

60Using Your Projector
Why am I unable to access the 
SMTP server?1Check with your MIS or network 
administrator whether the SMTP server 
function is open for the projector and the IP 
assigned to the projector is allowed to access 
the SMTP server. The projector’s SMTP 
socket port number is 25, this cannot be 
changed.
2Check if the out going SMTP server, user 
name, and password are set correctly.
3Some SMTP servers will check whether the 
mail address of From correlates with the 
User name and...