Dell Projector 1510X User Manual

Using Your Projector41
SUBNET MASK—Configure the Subnet Mask of the network connection.
G
ATEWAY—Check the Gateway address with your network/system administrator if 
you configure it manually.
DNS—Check the DNS Server IP address with your network/system administrator 
if you configure it manually.
S
TORE—Press   on the control panel or press Enter button on the remote control 
to save the changes made in network configuration settings.
R
ESET NETWORK—Select Ye s  to reset network configuration....

42Using Your Projector
MENU SETTINGS—Select and press   on the control panel or press Enter button 
on the remote control to activate menu settings. The menu settings consists of the 
following options:
MENU POSITION—Allows you to change the position of the OSD menu on 
the screen.
MENU TRANSPARENCY—Select to change the transparency level of the OSD 
background.
MENU TIMEOUT—Allows you to adjust the time for an OSD timeout. By 
default, the OSD disappears after 20 seconds of non-activity.
MENU...

Using Your Projector43
SCREEN—Select Dell to use the Dell logo as wallpaper. Select Captured to 
set the captured image as wallpaper.
RESET—Select and press   on the control panel or press Enter button on 
the remote control to delete the captured picture and set back to the 
default setting.
AUDIO SETTINGS—Select and press   on the control panel or press Enter button 
on the remote control to change audio settings. The audio settings menu consists 
of the following options:
AUDIO INPUT—Select the Audio...

44Using Your Projector
If an input signal is not detected during the delay period, the projector 
turns off the lamp and goes into power saving mode. If an input signal is 
detected within the delay period, the projector automatically turns on. If 
an input signal is not detected within two hours during power saving mode, 
the projector switches from Power Saving mode to Power Off mode. To 
turn on the projector press the Power button.
Q
UICK SHUTDOWN—Select Ye s to turn off the projector with a single...

Using Your Projector45
aGo to Others menu, press   on the control panel or press Enter 
button on the remote control and then select 
Pa s s w o r d to Enable 
the password setting.
bEnabling the Password function will pop up a character screen, key 
in a 4-digit number from the screen and press   on the control 
panel or press 
Enter button on the remote control.
cTo confirm, enter the password again. 
dIf the password verification is successful, you may resume with 
accessing the projectors functions...

46Using Your Projector
4To delete the password, select Delete.
CHANGE PASSWORD—Key in the original password, then enter the new 
password and confirm the new password again.
CLOSED CAPTION—Select On to enable close caption and activate the closed 
caption menu. Select an appropriate closed captions option: CC1, CC2, CC3, and 
CC4. 

Using Your Projector47
 NOTE: Closed caption option is available for NTSC only.
TEST PATTERN—Test Pattern is used to test focus and resolution.
You can enable or disable the Te s t  Pa t t e r n by selecting Off, 1 or 2. You can also 
invoke the Te s t  Pa t t e r n  1 by pressing and holding down   and   buttons on the 
control panel simultaneously for 2 seconds. You can also invoke the test pattern 2 
by pressing and holding down   and   buttons on the control panel 
simultaneously for 2 seconds....

48Using Your Projector
Managing the Projector From Web 
Management
Configuring the Network Setting
If the projector is connected to a network, you can access the projector using a web 
browser by configuring the network setting (TCP/IP). When using the network 
function, the IP address should be unique. For configuring the network setting, 
refer to Network on page 40.
Accessing Web Management
Use Internet Explorer 5.0 and above or Netscape Navigator 7.0 and above and 
enter the IP address. You can now...

Using Your Projector49
Managing Properties
Home
• Access the Web Management Home page by entering the projector’s IP 
address at the web browser. See Network on page 40.
•Language: Allows you to set the language for web management. 

50Using Your Projector
Network Settings
See OSD section on page 40.
•Set up the Model Name, Projector Name, Location and Contact 
information (up to 21 characters for each field). Press Save to store the 
settings.
• Choose DHCP to assign an IP address to the projector from a DHCP server 
automatically, or Manual to assign an IP address manually.
•Set up the IP Address, Device ID and Po r t information on the Crestron 
function.