Dell P2210 Users Guide

							 
Notes, Notices, and Cautions  
 
Information in this document is subject to change without notice.  
2009 -    
Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.  
Trademarks used in this text:  Dell  and the  DELL  logo are trademarks of Dell Inc;   Microsoft  and  Windows  are either trademarks or registered trademarks of Microsoft Corporation in 
the United States and/or other countries.ENERGY STAR is a registered trademark of the U.S. Environmental Protection Agency. As an ENERGY STAR partner, Dell Inc. has 
determined that this product meets the ENERGY STAR guidelines for energy efficiency.   
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any 
proprietary interest in trademarks and trade names other than its own.  
Model P2210f & P2210t   
January 2010  Rev. A03   About Your Monitor  
 
Setting Up the Monitor  
 
Operating the Monitor  
Troubleshooting   
Appendix  
     
NOTE:  A NOTE indicates important information that helps you make better use of your computer. 
CAUTION:   A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
  WARNING:  A WARNING indicates a potential for property damage, personal injury or death.  
						

							Back to Contents Page    
   
About Your Monitor   
 
Package Contents    
Your monitor ships with the components shown below. Ensure that you have received all the components and  contact Dell  if something is missing.  Package Contents
Product Features
Identifying Parts and Controls
Monitor Specifications
Plug and Play Capability
Universal Serial Bus (USB) Interface
LCD Monitor Quality and Pixel Policy
Maintenance Guidelines
  NOTE:  Some items may be optional and may not ship with your Monitor. Some features or media may not be available in certain countries.
NOTE:  Stand and cables are not included when purchased with OptiPlex™ USFF 780/OptiPlex SFF 980 AIO stands. 
  NOTE:  To set up with the respective AIO stand, please refer to the respective stand setup guide for setup instructions.
  l Monitor   
  l Stand  
  l Power Cable    
						

							   
Product Features  
The  P2210  flat panel display has an active matrix, thin - film transistor (TFT), liquid crystal display (LCD). The monitor features include:   
■  22 - inch (558.68 mm) viewable area display (Measured diagonally).   
■  1680 x 1050  resolution, plus full - screen support for lower resolutions.   
■  Wide viewing angle to allow viewing from a sitting or standing position, or while moving from side - to - side.   
■  Tilt, swivel, vertical extension and rotate adjustment capability.   
■  Removable pedestal and Video Electronics Standards Association (VESA) 100 mm mounting holes for flexible mounting solutions.   
■  Plug and play capability if supported by your system.   
■  Retractable label card allows convenient access to monitor serial number for technical support and easily hidden away providing label - free clean look.  
■  On - Screen Display (OSD) adjustments for ease of set - up and screen optimization.   
■  Software and documentation media includes an information file (INF), Image color Matching File (ICM), and product documentation.   
■  Energy Saver feature for Energy Star compliance.   
■  Security lock slot.  
■  Asset Management Capability.   
■  Capability to switch from wide aspect to standard aspect ratio while maintaining the image quality.   
■  EPEAT Gold Rating.  
■   Halogen Reduced .  
Identifying Parts and Controls  
Front View     l VGA Cable (attached to the monitor)   
  l DVI Cable   
    l USB up stream  cable (enables the USB ports on the monitor) 
    l Drivers and Documentation  media   
l Quick Setup Guide    
l Safety Information    
						

							   
Back View  
     
Front View   Front panel controls    
Label   Description  
1   Preset Modes (default, but configurable)
2   Brightness & Contrast (default, but configurable)
3   Menu
4   Exit
5   Power (with power light indicator)
Back view Back view with monitor stand
Label   Description   Use  
1   VESA mounting holes   (100 mm x 100 mm  -  
behind attached base plate) Wall mount monitor using VESA compatible wall mount kit (100 mm x 100 mm)   
2   Stand removal button    Release stand from monitor. 
3   Security lock slot   Secures monitor with security cable lock   
4   Dell Soundbar mounting brackets Attaches the optional Dell Soundbar.
5   Information mark  Help locating regulatory and barcode labels
6   Cable management slot Organizes cables by placing them through the slot.  
						

							Label  Card View  
 
Side View    NOTE:  Monitor shipped with label card fully inserted in USB compartment. Pull out the label card to access the barcode serial number label and regulatory rating label.
Back View with label card pulled out   
Front View with label card pulled out   
Label   Description   Use  
1   Regulatory label  Lists the regulatory approvals.
2   Barcode serial number label T o contact Dell for technical support.
   
						

							   
Bottom View    
   
Monitor Specifications  
Flat Panel Specifications    
Left view   R ight view  
Label Description Use
1 USB downstream ports Connect your USB devices.
2 Label card  Provide clean monitor back view when reference to labels is not required. 
Bottom view    Bottom view with monitor stand  
Label Description   Use  
1 AC power cord connector Connect the power cable 
2 DC power  connector  for Dell Soundbar. Connect the power cord for the soundbar (optional)
3 DisplayPort connector  Connect your computer DP cable 
4 DVI connector Connect your computer DVI cable 
5 VGA connector Connect your computer VGA cable   
6 USB upstream port Connect the USB cable that came with your monitor to the monitor and the 
computer. Once this cable is connected you can use the USB connectors on 
the side and bottom of the monitor.
7 USB downstream ports Connect your USB devices. You can only use this connector after you have 
connected the USB cable to the computer and USB upstream connector on 
the monitor.
Screen type Active matrix  -   TFT LCD
Panel type  TN  
						

							*[P2210] color gamut (typical) is based on CIE1976 ( 83% ) and CIE1931 (72%) test standards.   
Resolution  Specifications  
Supported Video Modes  
Preset Display Modes  
Electrical  Specifications  Screen dimensions 22 inches (22 - inch viewable 
image size)
Preset display area: 473.76(H)X296.1(V)
Horizontal 473.76 mm (18.7 inches)
Vertical 296.1 mm (11.7 inches)
Pixel pitch 0.282 mm
Viewing angle 160° (verticalyfW\SLFDl
170° (horizontalyfW\SLFDl  
Luminance output 250 CD/m ² ( typical)
Contrast ratio 1000 to 1 (typical), 10000 to 1 
(typical Dynamic Contrast On)  
Faceplate coating Antiglare with hard - coating 3H
Backlight 2 - CCFL edgelight system
Response Time 5ms panel typical
Color depth 16.7 million colors
Color Gamut 83%*
Horizontal scan range 30 kHz to 83 kHz (automatic)
Vertical scan range 56 Hz to 75 Hz (automaticyf
Maximum preset resolution 1680 X 1050 at 60 Hz
Video display capabilities (DVI & DP playback) 480p, 576p, 720p ,  1080p 
Display Mode   Horizontal Frequency (kHz)   Vertical Frequency (Hz)   Pixel Clock (MHz)   Sync Polarity (Horizontal/Vertical)  
VESA, 720 x 400 31.5   70.0   28.3   - /+  
VESA, 640 x 480  31.5   60.0   25.2   - / -  
VESA, 640 x 480 37.5   75.0   31.5   - / -  
VESA, 800 x 600 37.9   60.3   40.0   +/+  
VESA, 800 x 600 46.9   75.0   49.5   +/+  
VESA, 1024 x 768 48.4   60.0   65.0   - / -  
VESA, 1024 x 768 60.0   75.0   78.8   +/+  
VESA, 1152 x 864 67.5   75.0   108.0   +/+  
VESA, 1280 x 1024  64.0   60.0   108.0   +/+  
VESA, 1280 x 1024  80.0   75.0   135.0   +/+  
VESA, 1680 x 1050   65.2   60.0   146.0   - /+  
Video input signals Analog RGB, 0.7 Volts +/ -  5%, positive polarity at 75 ohm input 
impedance   
Digital DVI - D TMDS, 600mV for each differential line, positive polarity at 
50 ohm input impedance  
DP 1.1a signal input support
Synchronization input signals TTL levels required and separate syncs (including Trigger points), SOG 
(Composite SYNC on green)
AC input 
voltage/frequency/current 100 to 240 VAC/50 or 60 Hz  +  3 Hz/1.5A (Typical)  
						

							Physical  Characteristics  
Environmental  Characteristics  
Power Management Modes  
If you have VESA's DPM™ compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in 
use. This is referred to as  Power Save Mode *. If the computer detects input from keyboard, mouse, or other input devices, the monitor automatically resumes 
functioning. The following table shows the power consumption and signaling of this automatic power saving feature:   Inrush current 120 V: 30 A (Max.)  
240 V: 60 A (Max.) 
Connector type 15 - pin D - subminiature, blue 
connector; DVI - D, white 
connector;DP,black connector.
Signal cable type Digital: Detachable, DVI - D, Solid 
pins, shipped detached from the 
monitor  
Analog:attachable, D - Sub, 15pins, 
shipped attached to the monitor  
Dimensions (with stand)
Height (extended)  461.91 mm (18.18 inches) 
Height (compressed) 361.91 mm (14.24 inches )  
Width 511.77 mm (20.15 inches) 
Depth 184.12 mm  ( 7.25 inches) 
Dimensions (without stand)
Height  334.17 mm  ( 13.16 inches) 
Width 511.77 mm  ( 20.15 inches) 
Depth 65.00 mm (2.56 inches )  
Stand dimensions
Height (extended)  363.82 mm  ( 14.32 inches) 
Height (compressed) 323.52mm (12.74 inches )  
Width 279.92 mm  ( 11.02 inches) 
Depth 184.12 mm  ( 7.25 inches) 
Weight
Weight with packaging 18.2 lb (8.25 kg)
Weight with stand assembly and cables 14.22 lb (6.45 kg)
Weight without stand assembly  
(For wall mount or VESA mount considerations  -  
no cables) 9.97 lb (4.52kg)
Weight of stand assembly 3.88 lb (1.76 kg) 
Temperature  
Operating 0° to 40 ° C 
Non - operating Storage:  - 20° to 60° C ( - 4° to 140° Fyf  
Shipping:  - 20° to 60° C ( - 4° to 140° Fyf
Humidity
Operating 10% to 80% (non - condensing)
Non - operating Storage: 5% to 90% (non - condensing)  
Shipping: 5% to 90% (non - condensing)
Altitude
Operating 3,657.60 m (12,000 ft) max
Non - operating 12,192 m (40,000 ft) max
Thermal dissipation 88.77 BTU/hour (maximum)  
75.12 BTU/hour (typical)
VESA Modes Horizontal Sync Vertical Sync  Video Power Indicator Power Consumption
Normal  Active Active Active  Blue 22 W (typical)  
						

							The OSD will only function in the normal operation mode. When any button is pressed in Active - off mode, one of the following messages will be displayed:   
 
Activate the computer and the monitor to gain access to the  OSD.  
* Zero power consumption in OFF mode can only be achieved by disconnecting the main cable from the monitor.  
Pin Assignments  
VGA Connector  
 
 operation
Active - off mode Inactive Inactive Blanked Amber Less than  0.3  W
Switch off     -        -       -   Off Less than  0. 3 W
 
   
  NOTE:  This monitor is  ENERGY STAR ®
- compliant as well as TCO 03 power management compatible.  
Pin 
Number 15 - pin Side of the Co nnected Signal Cable
1   Video - Red  
2   Video - Green
3   Video - Blue
4   GND
5   Self - test
6   GND - R
7   GND - G
8   GND - B
9   Computer 5V/3.3V
10   GND - sync
11   GND
12   DDC data
13   H - sync
14   V - sync
15   DDC clock  
						

							 
DisplayPort Connector  
 Pin 
Number 24 - pin Side of th e C o nnected  Signal Cable
1   TMDS RX2 -
2   TMDS RX2+
3   TMDS Ground
4   Floating
5   Floating
6   DDC Clock
7   DDC Data
8   Floating
9   TMDS RX1 -
10   TMDS RX1+
11   TMDS Ground
12   Floating
13   Floating
14   +5V/+3.3V power
15   Self test 
16   Hot Plug Detect
17   TMDS RX0 -
18   TMDS RX0+
19   TMDS Ground
20   Floating
21   Floating
22   TMDS Ground
23   TMDS Clock+
24   TMDS Clock -
Pin 
Number 20 - pin Side of the Connected Signal Cable  
1   ML0(p)
2   GND
3   ML0(n)
4   ML1(p)
5   GND
6   ML1(n)
7   ML2(p)
8   GND
9   ML2(n)