dell latitude cpt vcpt s series series User Manual

24 Dell Latitude CPt V/CPt S Series and CPx H/CPx J Series Service Manual
	
()!
+,

NOTE: Use a magnetic screwdriver to reassemble the LCD panel in the dis-
play. Secure the right side first.
1. Place the bottom edge of the LCD panel in the bottom of the top cover and 
elevate the top of the panel with your hand.
2. Carefully connect the LCD flex cable to the connector on the left edge of 
the LCD panel.
Do not force the LCD flex cable into the connector. If you have trouble, 
check...

support.dell.comDell Latitude CPt V/CPt S Series and CPx H/CPx J Series Service Manual 25
)30
	 +4/+*1


	
8)30
	 +4/+
	
.)!
	
$#

$
*
1. Remove the four 5-mm screws securing the LCD panel to the top cover.
2. Disconnect the two-wire back-light plug from the connector on the inverter.
3. Lift the LCD panel and carefully disconnect the flex cable from the 
connector on the left edge of the LCD panel. 
4. Remove the LCD...

26 Dell Latitude CPt V/CPt S Series and CPx H/CPx J Series Service Manual
	
.)!
+,


1. Disconnect the LCD flex cable from the ZIF connector on the inverter.
2. Remove the three 3-mm screws securing the inverter to the top cover.
3. Remove the inverter from the top cover.
	
.)!
+-
1. Remove the 4-mm screw securing the metal cable clip to the left hinge of 
the display-assembly top cover.
2. Remove the cable out from under the plastic strain relief...

support.dell.comDell Latitude CPt V/CPt S Series and CPx H/CPx J Series Service Manual 27
7. Fold the LCD flex cable at the crease as shown in Figure 17, so that the 
name of the LCD panel manufacturer faces up. The manufacturer is either 
Torisan (T-Sanyo) or Sharp. 
The connectors are identical on the Torisan and Sharp LCD panels, but they 
are mounted reverse with respect to each other. This means that pin 1 on 
the Torisan panel connector is at the opposite end when compared to pin 1 
on the Sharp...

28 Dell Latitude CPt V/CPt S Series and CPx H/CPx J Series Service Manual
	
>)30

3. Place the inverter in the cover top.
4. Reinstall the three 3-mm screws that secure the inverter to the top cover.
5. Connect the LCD flex cable to the ZIF connector on the inverter.
	
.)!
+,

1. Find the manufacturer’s name on the back of the LCD panel that is to be 
installed. The manufacturer is either Torisan or Sharp.
2. Make sure that the LCD flex cable is folded...

support.dell.comDell Latitude CPt V/CPt S Series and CPx H/CPx J Series Service Manual 29
7. Connect the two-wire back-light plug to the connector on the inverter.
When the plug is all the way in the connector, the key slot in the center of 
the plug should 
not be visible. If you can see the key slot, the plug is not in 
the connector correctly. Pull the plug out, turn the plug over, and reinsert it 
into the connector. 
8. Reinstall the four 5-mm screws to secure the LCD panel to the top cover.

	...

30 Dell Latitude CPt V/CPt S Series and CPx H/CPx J Series Service Manual

4/+
The palmrest assembly consists of the touch pad and the palmrest.

%




&
(

*(!+

 (
#


%


















*(!+ 
%
$






%


...

support.dell.comDell Latitude CPt V/CPt S Series and CPx H/CPx J Series Service Manual 31

+
$

$




#

 
5. Turn the computer upside down on a flat work surface.
6. Remove the five 20-mm screws that secure the palmrest to the computer.
These screws, labeled with a “circle P,” are located underneath the front 
edge of the computer (see Figure 19).
7. Turn the computer right-side up on the work surface.
8. Disconnect the palmrest...

32 Dell Latitude CPt V/CPt S Series and CPx H/CPx J Series Service Manual
*+

%




&(


*(!+

 (
#%

















*(!+ 
%
$






%


%
 
	


$
1. Remove the main battery and secondary battery (if...

support.dell.comDell Latitude CPt V/CPt S Series and CPx H/CPx J Series Service Manual 33
4/+
The modem assembly is optional. The modem (if present) must be removed 
before the main system board can be removed (see Figure 21).






##%





%
%


 
	
%#

$
1. Remove the main battery and secondary battery (if present).
2. Remove the keyboard assembly.
3. Remove the display assembly.
4....