dell inspiron 8200 User Manual

							Pin Assignments for I/O Connectors: Dell Inspiron 8200
45DOCK_+DC_IN 145SRDATA#
46 DOCK_+DC_IN 146SINDEX#
47 DOCK_+DC_IN 147GND
48 DOCK_+DC_IN 148NC
49 GND 149+5VALW
50 LOW_PWR 150NC
51 HSYNC 151GND
52 VSYNC 152CLK_SPCI
53 GND 153GND
54 DOCKED 154SAD0
55 USB_VD1+ 155SAD1
56 USB_VD1- 156SAD2
57 GND 157SAD3
58 USB_VD2+ 158SAD4
59 USB_VD2- 159SAD5
60 DOCKOCI# 160SAD6
61 RUN_ON# 161GND
62 GND 162SAD7
63 NC 163SAD8
64 DOCK_SCLK 164SC/BE0#
65 DOCK_LRCK 165SAD9
66 DOCK_MCLK 166SAD10
67 GND 167SAD11
68 +12V 168SAD12
69 AFD# 169GND
70 ERROR# 170SAD13
71 ACK# 171SAD14
file:///F|/Service%20Manuals/Dell/Inspiron/8200/pinouts.htm (8 of 10) \
[2/28/2004 7:40:21 AM] 
						

							Pin Assignments for I/O Connectors: Dell Inspiron 8200
72GND 172SAD15
73 INIT# 173SAD16
74 SLCT_IN# 174SC/BE1#
75 BUSY 175CD/BE2#
76 PE 176GND
77 SLCT 177SAD17
78 GND 178SAD18
79 DAT_SMB 179SAD19
80 DCLK_SMB 180SAD20
81 SMB_INIT# 181SAD21
82 GND 182GND
83 DAT_DOCKSM1 183SAD22
84 CLK_DOCKSM1 184SAD23
85 DAT_DOCKKBD 185SAD24
86 CLK_DOCKKBD 186SC/BE3#
87 GND 187SAD25
88 RI0 188GND
89 CTS0 189SAD26
90 RTS0 190SAD27
91 DSR0 191SAD28
92 GND 192SAD29
93 DTR0 193SAD30
94 TXD0# 194SAD31
95 RXD0# 195GND
96 DCD0 196NC
97 NC 197NC
98 +5VSUS 198NC
file:///F|/Service%20Manuals/Dell/Inspiron/8200/pinouts.htm (9 of 10) \
[2/28/2004 7:40:21 AM] 
						

							Pin Assignments for I/O Connectors: Dell Inspiron 8200
99NC 199NC
100 NC 200GND
IEEE 1394 Connector 
 
Pin Signal
1 TPB-
2 TPB+
3 TPA-
4 TPA+
Back to Contents Page
 
 
 
file:///F|/Service%20Manuals/Dell/Inspiron/8200/pinouts.htm (10 of 10)\
 [2/28/2004 7:40:21 AM] 
						

							Removing and Replacing Parts: Dell Inspiron 8200
Back to Contents Page 
Removing and Replacing Parts 
Dell™ Inspiron™ 8200
 Before You Begin
 System Components
 Hard Drive and Fixed Optical Drive
 System Upgrades
 Keyboard
 Display
 Microprocessor Thermal-Cooling Assembly
 Microprocessor Module
 Video Graphics Board
 Palm Rest
 Reserve Battery
 System Board
 Battery and Module Bay Latches
 Battery Charger Board
 LED Board
 Fan
 RJ-11/RJ-45 Module
Back to Contents Page
 
 
 
file:///F|/Service%20Manuals/Dell/Inspiron/8200/remove.htm [2/28/2004 7:\
40:21 AM] 
						

							Microprocessor Thermal-Cooling Assembly: Dell Inspiron 8200
Back to Contents Page 
Microprocessor Thermal-Cooling 
Assembly 
Dell™ Inspiron™ 8200
NOTICE: Disconnect the computer and attached devices from electrical outlets 
and remove any installed batteries. 
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by 
periodically touching unpainted metal on the computer. 
 
1 microprocessor thermal-
cooling assembly
file:///F|/Service%20Manuals/Dell/Inspiron/8200/thermal.htm (1 of 3) [\
2/28/2004 7:40:31 AM] 
						

							Microprocessor Thermal-Cooling Assembly: Dell Inspiron 8200
2microprocessor retaining 
clip
Removing the Microprocessor Thermal-Cooling 
Assembly 
1.  Follow the instructions in Preparing to Work Inside the Computer. 
2.  Remove the 
keyboard. 
3.  Remove the 
hinge cover. 
4.  Insert a non-marring plastic scribe into the latch mechanism at the left\
 side of  the microprocessor retaining clip. Pry open the clip by pivoting the top\
 of the 
screwdriver toward the right side of the computer. 
 
1 microprocessor thermal-
cooling assembly
file:///F|/Service%20Manuals/Dell/Inspiron/8200/thermal.htm (2 of 3) [\
2/28/2004 7:40:31 AM] 
						

							Microprocessor Thermal-Cooling Assembly: Dell Inspiron 8200
NOTICE: To ensure maximum cooling for the microprocessor, do not touch the 
heat transfer areas on the microprocessor thermal-cooling assembly. The \
oils in 
your skin reduce the heat transfer capability of the thermal pads. 
5.  Lift out the thermal-cooling assembly. 
Back to Contents Page
 
 
 
file:///F|/Service%20Manuals/Dell/Inspiron/8200/thermal.htm (3 of 3) [\
2/28/2004 7:40:31 AM] 
						

							Before You Begin: Dell Inspiron 8200
Back to Contents Page 
Before You Begin 
Dell™ Inspiron™ 8200
  Preparing to Work Inside the Computer
  Recommended Tools
  Computer Orientation
  Screw Identification
Preparing to Work Inside the Computer
 CAUTION: Only a certified service technician should perform repairs on 
your computer. Damage due to servicing that is not authorized by Dell 
is not covered by your warranty. Read and follow applicable safety 
instructions in the Owners Manual that came with the computer.
 CAUTION: Allow the computer to cool to room temperature before 
working inside the computer.
NOTICE: To avoid damaging the computer, perform the following steps before 
you begin working inside the computer. 
1.  Ensure that the work surface is flat and clean to prevent scratching the\
  computer cover. 
2.  Save any work in progress and exit all open programs. 
3.  Turn off the computer and all attached devices. 
HINT: Before turning off the computer, ensure that the computer is not in a 
power-management mode. 
4.  Ensure that the computer is undocked. 
file:///F|/Service%20Manuals/Dell/Inspiron/8200/begin.htm (1 of 6) [2/\
28/2004 7:40:48 AM] 
						

							Before You Begin: Dell Inspiron 8200
5.  Disconnect the computer from the electrical outlet. 
6.  To avoid possible damage to the system board, wait 10 to 20 seconds and \
then disconnect any attached devices. 
7.  Disconnect all other external cables from the computer. 
8.  Remove any installed PC Cards or plastic blanks from the PC Card slot. 
9.  Close the display and turn the computer upside down on a flat work surfa\
ce. 
10.  Remove the battery from the battery bay. 
NOTICE: To avoid component damage, always remove any installed batteries 
before you service the computer. 
11.  Remove any device installed in the module bay. 
12.  To dissipate static electricity while you work, periodically touch an un\
painted  metal surface on the computer chassis. 
13.  Handle components and cards by their edges, and avoid touching pins and \
 contacts. 
Recommended Tools
The procedures in this document require the following tools:
l     #1 magnetized Phillips screwdriver
l     Small flat-blade screwdriver
l     Microprocessor extractor
l     Nonmarring plastic scribe
l     Flash BIOS update program floppy disk or CD (provided when needed to 
upgrade the BIOS)
file:///F|/Service%20Manuals/Dell/Inspiron/8200/begin.htm (2 of 6) [2/\
28/2004 7:40:48 AM] 
						

							Before You Begin: Dell Inspiron 8200
Computer Orientation
 
Screw Identification
When you are removing and replacing components, photocopy the placemat a\
s a tool 
to lay out and keep track of the component screws. The placemat provides\
 the 
number of screws and the sizes.
file:///F|/Service%20Manuals/Dell/Inspiron/8200/begin.htm (3 of 6) [2/\
28/2004 7:40:48 AM]