Dell Inspiron 3000 Service Manual
Here you can view all the pages of manual Dell Inspiron 3000 Service Manual. The Dell manuals for Notebook are available online for free. You can easily download all the documents as PDF.
Page 81
Removing and Replacing Parts 4-45 Base Assembly The base assembly consists of the following components: •IR lens •Processor board •LVDS board (13.3-inch LCD only) •USB board •Main board •Audio bezel •Audio board •PC Card cage •Latch assembly •BIOS door •Rubber feet The following subsections provide removal and replacement procedures for most of the components of the base assembly. Procedures for the BIOS door, rubber feet, and 13.3-inch bumpers are not shown because they are obvious. The procedures...
Page 82
4-46 Dell Inspiron 3000 Series Service Manual Figure 4-29. Base Assembly base assembly main board audio board LVDS board(13.3-inch LCD only) IR lens processor board audio bezel PC Card cage USB boardconnector JP16
Page 83
Removing and Replacing Parts 4-47 IR Lens Figure 4-30. IR Lens Removal Remove the IR lens by gently pulling straight up on the lens with the fingers of one hand. IR lens
Page 84
4-48 Dell Inspiron 3000 Series Service Manual Processor Board Figure 4-31. Processor Board Removal Remove the processor board from the main board. The processor board is held in place on the main board by connectors JP18 and JP19. Using the fingers of one hand, gently remove the processor board from the main board by pulling straight up. Do not rock the processor board to remove it. This may damage the two connectors on the processor board or the main board. There is a rubber bumper on the upper...
Page 85
Removing and Replacing Parts 4-49 LVD S B o a rd The LVDS board is present on computers with a 13.3-inch LCD. If you have a 12.1-inch LCD, skip this subsection. Figure 4-32. LVDS Board Removal To remove the LVDS board, follow these steps: 1. Remove LVDS board screw G2. This is the other screw that you left in place when you removed the 13.3-inch LCD cable harness from connector JP1 on the LVDS board. 2. Remove the LVDS board from the main board. The LVDS board is held in place on the main board by...
Page 86
4-50 Dell Inspiron 3000 Series Service Manual USB Board Figure 4-33. USB Board Removal To remove the USB board, follow these steps: 1. Remove USB board screw U1. 2. Disconnect the USB board from connector JP9 on the main board. With the fingers of one hand, gently pull the USB board straight up about 1/4-inch to free it from connector JP9. Then turn the board slightly to the right to remove it from the corner of the main board and the base assembly. (screw U1is 5 mm) 5 mm U1 connector JP9 USB board
Page 87
Removing and Replacing Parts 4-51 Main Board Figure 4-34. Main Board Removal To remove the main board, follow these steps: 1. Remove the processor board. 2. If one is installed, remove the LVDS board. Otherwise, go to step 3. 3. Remove the USB board. 4. Remove main board screws M1, M2, and M3. 5. Remove standoff nuts ST1, ST2, and ST3. 6. Remove the main board from the base assembly. Lift the end of the board nearest the front of the computer, and pull the board up and out of the computer. Remove the...
Page 88
4-52 Dell Inspiron 3000 Series Service Manual Audio Bezel Figure 4-35. Audio Bezel Removal Remove the audio bezel by gently pulling it from the three audio jacks on the left side of the main board. This bezel usually drops out when the main board is removed from the computer. audio bezel
Page 89
Removing and Replacing Parts 4-53 Audio Board Figure 4-36. Audio Board Removal To remove the audio board, follow these steps: 1. Remove the main board. 2. Remove the audio board from the bottom of the main board. The audio board is held in place by two connectors on the main board (JP26 and JP22) and two connectors on the audio board (JP1 and JP2). The con- nectors are different sized to ensure correct placement when reinstalling the audio board. Ensure that you reinstall the audio board when you...
Page 90
4-54 Dell Inspiron 3000 Series Service Manual PC Card Cage Figure 4-37. PC Card Cage Removal To remove the PC card cage, follow these steps: 1. Remove the main board. Use a support for the main board to prevent the board from flexing when the card cage screws are removed 2. Remove PC Card cage screws P1, P2, P3, and P4. Screws P2 and P4 have ground springs attached. There are plastic insulators on the main board, below the ground springs. 3. Remove the top of the card cage. Disconnect the top from...