Dell In2030m Users Guide

2. Select the  Settings  tab.   
3. Set the screen resolution to  1366 x 768  (for IN1930) or  1600 x 900  (for IN2030M).   
4. Click  OK .   
Windows Vista ®  or Windows ®  7:  
1. Right - click on the desktop and select  Personalization .   
2. Click  Change Display Settings .   
3. Move the slider - bar to the right by pressing and holding left - mouse button and adjust the screen resolution to  1366 x 768  (for IN1930) or  1600 x 900  
(for IN2030M).   
4. Click  OK .   
If you do not see 1366 x 768...

 
Back to Contents Page    NOTE:  The stand base is detached when the monitor is shipped from the factory.   

Back to Contents Page   
Setting Up Your Monitor   
 
IN1930/IN2030M  monitor   
Setting the display resolution to  1366 x 768 (for IN1930) or 1600 x 900 (for 
IN2030M) ( Maximum)  
For optimal display performance while using the Microsoft Windows operating systems, set the display resolution to 1366 x 768 (for IN1930) or 1600 x 900 (for 
IN2030M) pixels by performing the following steps:  
In Windows XP:  
1. Right - click on the desktop and click  Properties .  
2. Select the  Settings  tab.  
3. Move...

 IN1930/IN2030M  
Information in this document is subject to change without notice.  
2011 .  
Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.   is strictly forbidden.  
Trademarks used in this text:  Dell  and the  DELL  logo are trademarks of Dell Inc.;   Microsoft and Windows  are either registered trademarks or trademarks of Microsoft Corporation in 
the United States and/or other countries. ENERGY STAR  is a registered trademark of the U.S....

Back to Contents Page    
 
Setting Up the Monitor   
IN1930/IN2030M  Monitor Users Guide  
   Attaching the Stand  
   Connecting Your Monitor  
   Removing the Stand   
   Attaching the Dell Soundbar (Optional)  
   
Attaching the Stand  
1. Assemble the stand riser to stand base.   
 
2. Attach the stand assembly to the monitor:  
 
Connecting Your Monitor  NOTE:  The stand base is detached when the monitor is shipped from the factory.
a. Place the monitor stand base on a stable table top.
b. Slide...

To connect your monitor to the computer:  
1. Turn off your computer and disconnect the power cable.
2. Connect either the white (digital DVI - D) or the blue (analog VGA) display connector cable to the corresponding video port on the back of your 
computer. Do not use both cables on the same computer. Use both the cables only when they are connected to two different computers with 
appropriate video systems.   
Connecting the Blue VGA Cable  
 
   
Connecting the white DVI cable  (for IN2030M only)...

 
To attach the soundbar:  
Back to Contents Page    CAUTION:  Do not use with any device other than the Dell Soundbar. 
1.  Working from the back of the monitor, attach Soundbar by aligning the two slots with the two tabs along the bottom of the monitor.
2.  Slide the Soundbar to the left until it snaps into place.
3.  Connect the Soundbar with the DC power connector from the Soundbar Power Adapter.
4.  Insert the mini stereo plug from the back of the Soundbar into the computers audio output jack.  

Back to Contents Page    
 
Troubleshooting  
 
IN1930/IN2030M  monitor   
   Self - Test  
   Built - in Diagnostics  
   Common Problems    
   Product Specific Problems  
   Dell Soundbar Problems  
   
   
Self - Test  
Your monitor provides a self - test feature that allows you to check whether your monitor is functioning properly. If your monitor and computer are properly 
connected but the monitor screen remains dark, run the monitor self - test by performing the following steps:   
1. Turn off...

Built - in Diagnostics  
Your monitor has a built - in diagnostic tool that helps you determine if the screen abnormality you are experiencing is an inherent problem with your monitor, or 
with your computer and video card.  
 
To run the built - in diagnostics:  
1. Ensure that the screen is clean (no dust particles on the surface of the screen).   
2. Unplug the video cable(s) from the back of the computer or monitor. The monitor then goes into the self - test mode.   
3. Press and hold the  Button 1...

   
Product Specific Problems  
 Problems   l Auto Adjust via OSD.  
l Adjust brightness & contrast controls via OSD.    
NOTE: When using DVI - D, the positioning adjustments are not available.   
Horizontal/Vertical Lines Screen has one or more lines l Reset the monitor to Factory Settings.  
l Perform Auto Adjust via OSD.    
l Adjust Phase and Pixel Clock controls via OSD.  
l Perform monitor self - test feature check and determine if these lines are also in self - test 
mode.  
l Check for bent or...