Dell In2020m Users Guide

							Dell IN2020/IN2020M Flat Panel Monitor Users Guide
file:///C|/Users/santhosh_v/Desktop/UG_en/about.htm[3/27/2013 12:20:59 PM]
(kHz)(MHz)
VGA,  720 x  40031.469 70.087 28.3 -/+
VGA,  640 x  480 31.469 59.940 25.2 -/-
VGA ,  640 x  480 37.500 75.000 31.5 -/-
VESA, 800 x  600 37.879 60.317 40.0 +/+
VESA, 800 x  600 46.875 75.000 49.5 +/+
VESA, 1024 x  768 48.363 60.004 65.0 -/-
VESA, 1024 x  768 60.023 75.029 78.8 +/+
VESA. 1152 x  864 67.50075.000108.0 +/+
VESA,  1280 x  1024 64.00060.000108.0 +/+
VESA,  1280 x  1024 79.97675.025135.0 +/+
VESA, 1600 x  900 55.54060.00097.75 +/ -
 
Electrical
Model IN2020/IN2020M
Video input signals Analog  RGB,  0.7 Volts +/ - 5%, positive polarity at 75  ohm input impedance  
D
igital  DVI-D  TMDS,  600mV for each  differential line, positive polarity at 50  ohm input
impedance  (for  IN2020M)
Synchronization input signals Separate  horizontal and  vertical  synchronizations,  polarity-free TTL level,  SOG
(Composite SYNC on green)
AC input voltage/frequency/current 100 to  240 VAC/50 or 60  Hz  +
 3 Hz/1.6A (Max.)
Inrush  iso surge current 120 V: 30  A  (Max.)
240 V: 60  A  (Max.)
 
Physical Characteristics
Model IN2020/IN2020M
Connector type
D -sub: Blue  connectorDVI-D: White connector  (for  IN2020M only)
D -sub: Detachable, Analog, 15  pin, shipped attached  to  the monitor
 
						

							Dell IN2020/IN2020M Flat Panel Monitor Users Guide
file:///C|/Users/santhosh_v/Desktop/UG_en/about.htm[3/27/2013 12:20:59 PM]
Signal cable typeDVI-D: Detachable, DVI-D, Solid pins (optional)
Dimensions (with  stand)
Height363 mm  (14.30 inches)
Width 481 mm  (18.95  inches)
Depth 152
 mm  ( 5.98  inches)
Dimensions (without stand)
Height   288.00 mm (11.34 inches)
Width 481 mm  (18.95  inches)
Depth 61  mm  ( 2.38  inches)
Stand dimensions
Height 290 mm (11.43  inches)
Width 251 mm  (9.86 inches)
Depth 152 mm  (5.98 inches)
Weight
Weight  with packaging 5.6 kg (12.32  lb)
Weight  with stand  assembly and
cables 4.2
 kg (9.22 lb)
Weight  without  stand  assembly
(f or wall mount or VESA  mount
considerations - no cables) 2.9 kg (6.28 lb)
Weight  of stand  assembly 1.1 kg (2.47  lb)
 
Environmental
Model IN2020/IN2020M
Temperature
Operating 0°  to  40° C  (32°  to  104°F)
Non-operating Storage: -20° to  60° C  (-4°  to  140° F)
Shipping: -20° to  60° C  (-4°  to  140° F)
Humidity
Operating 10%  to  80%  (non-condensing)
 
						

							Dell IN2020/IN2020M Flat Panel Monitor Users Guide
file:///C|/Users/santhosh_v/Desktop/UG_en/about.htm[3/27/2013 12:20:59 PM]
Non-operatingStorage: 5% to  90%  (non-condensing)Shipping: 5% to  90%  (non-condensing)
Altitude
Operating 4,485 m (14,700 ft) max
Non-operating 12,191 m (40,000 ft) max
Thermal dissipation 256.08 BTU/hour (maximum)
119.5 BTU/hour (typical)
 
Plug and Play Capability
You  can  install the monitor in any Plug and  Play-compatible system. The  monitor automatically provides  the computer  system  with its  Extended  Display Identification  Data (EDID)
using  Display Data Channel (DDC) protocols so that  the system  can  configure itself and  optimize  the monitor settings. If  required, the user  can  select different settings, but in most
cases  monitor installation is automatic.
LCD Monitor Quality & Pixel Policy
During  the LCD  Monitor manufacturing process,  it  is not uncommon for one  or more  pixels to  become fixed  in an unchanging state. The  visible result  is a  fixed  pixel  that  appears as
an extremely tiny dark or bright discolored spot.  When  the pixel  remains  permanently  lit, it  is known as a  bright  dot.  When  the pixel  remains  black, it  is known as a  dark dot.  
In almost every case,  these fixed  pixels are hard to  see and  do not detract from  display  quality or usability. A  display  with 1 to  5 fixed  pixels is considered  normal  and  within
competitive  standards.   For  more  information, see Dell Support site at:   support.dell.com.
Maintenance Guidelines
Caring for Your  Monitor
CAUTION: Read and follow the  Safety Instructions before cleaning the
monitor.  
CAUTION:  Before  cleaning the monitor, unplug the monitor  from the
electrical outlet.  
Fo r  best practices,  follow  the instructions in the list below  while  unpacking, cleaning,  or handling your  monitor:
To clean your  antistatic  screen, lightly dampen a  soft, clean cloth  with water. If  possible, use a  special screen-cleaning tissue  or solution  suitable for the antistatic  coating.  Do
not use benzene, thinner, ammonia,  abrasive cleaners, or compressed  air.
Use  a  lightly-dampened, warm cloth  to  clean the monitor.  Avoid  using  detergent of any kind as some  detergents leave a  milky film on the monitor.  If  you notice  a  white powder  when  you unpack  your  monitor,  wipe it  off with a  cloth.Handle your  monitor with care as dark-colored monitors  may scratch and  show white scuff marks  more  than  lighter-colored monitors.  To help maintain the best image quality on your  monitor,  use a  dynamically changing screen saver and  turn  off your  monitor when  not in use.
Back to  Contents Page
 
 
						

							Dell IN2020/IN2020M Flat Panel Monitor Users Guide
file:///C|/Users/santhosh_v/Desktop/UG_en/setup.htm[3/27/2013 12:21:01 PM]
Back to  Contents Page
Setting Up the Monitor
Dell™ IN2020/IN2020M monitor Users Guide
  Attaching  the Base
  Connecting  the Monitor
   Attaching  the Soundbar (Optional)
  Removing the Monitor Stand
 
Attaching the Base
NOTE:  The  stand  is detached  when  the monitor is shipped from  the factory.
 
After placing the monitor panel on a  soft cloth  or cushion,  complete  the following steps to  attach the base.
1.  Fit the groove on the back  of the monitor to  the two tabs on the upper part of the stand.
2 .  Lower  the monitor so that  the monitor mounting  area snaps on to  or locks  on to  the stand.
Connecting the Monitor
CAUTION:  Before  you begin any of the procedures in this section, follow  the  safety instructions.
To connect your  monitor to  the computer  perform  the following steps/instructions:
 
						

							Dell IN2020/IN2020M Flat Panel Monitor Users Guide
file:///C|/Users/santhosh_v/Desktop/UG_en/setup.htm[3/27/2013 12:21:01 PM]
1.  Turn off your  computer  and  disconnect the power cable.2 .  Connect the white (digital  DVI-D),  or blue (analog VGA)  display  connector  cable  to  the corresponding  video  port on the back  of your  computer.  Do not use all the cables on the
same  computer.  Use all  of  the cables only  when  they are connected to  different computers with appropriate video  systems.
 
Connecting the blue VGA cable
Connecting the White DVI Cable* (for IN2020M only)
NOTE:  *Optional purchase item.  To purchase a  DVI cable, please visit Dell.com
NOTE: The  Graphics are used for the purpose  of illustration only. Appearance of the the computer  may vary.
After you have  completed connecting  the VGA/DVI cable, follow  the procedure below  to  complete  your  monitor setup: 1.  Plug the power cables  for your  computer  and  monitor into a  nearby outlet.
2 .  Turn on the monitor and  the computer.
If  your  monitor displays  an image,  installation is complete.  If  it  does  not display  an image,  see  Solving  Problems
.
Attaching the Soundbar (Optional)
 
						

							Dell IN2020/IN2020M Flat Panel Monitor Users Guide
file:///C|/Users/santhosh_v/Desktop/UG_en/setup.htm[3/27/2013 12:21:01 PM]
1.Working from  the rear of the monitor,  attach the Soundbar by aligning  the two slots with the two tabs along the bottom  rear of the monitor.
2. Slide the Soundbar to  the left  until it  snaps into place.
3.  Connect the S oundbar with the DC power connector.
4. Insert the mini stereo plug from  the rear of the Soundbar into the computers audio output jack or the monitors audio output jack.
NOTICE:  Do  not  use with any  device  other  than the Dell  Soundbar.
Removing the Monitor Stand
 
						

							Dell IN2020/IN2020M Flat Panel Monitor Users Guide
file:///C|/Users/santhosh_v/Desktop/UG_en/setup.htm[3/27/2013 12:21:01 PM]
After placing the monitor panel on a  soft cloth  or cushion,  complete  the following steps to  remove the base.1.  Press  and  hold the Stand  release  button.
2 .  Lift the stand  up  and  away  from  the monitor.
 
Back to  Contents Page
 
 
						

							Dell IN2020/IN2020M Flat Panel Monitor Users Guide
file:///C|/Users/santhosh_v/Desktop/UG_en/operate.htm[3/27/2013 12:21:03 PM]
Back to  Contents Page
Operating the MonitorDell™ IN2020/IN2020M monitor Users Guide  Using the Front Panel Controls  Using the On -Screen Display (OSD) Menu   Setting  the Maximum Resolution  Using the Dell Soundbar (Optional)  Using the Tilt 
Using the Front PanelUse  the control buttons on the side  of the monitor to  adjust  the characteristics of the image being displayed.  As you use these buttons to  adjust  the controls,  an OSD shows  the numeric values of the characteristics as they change.
  
1-2 Shortcut keys Use  this button for direct  access  to  the control menu  that  you define in the personalize  menu.
*The default settings are Preset Modes  Select and  Brightness/Contrast Select.
1
Preset  Modes  Select Use  this button for different display  preset modes on your  monitor.
2
Brightness/Contrast Use  this button to  access  the Brightness/Contrast control menu.
3
OSD Menu Use  this button to  open the On -Screen Display (OSD).  See 
Using the OSD Menu.
4
Exit Use  this button to  exit  the OSD menu.
5
Power button Use  the
 power button to  turn  the monitor on and  off.
The  white light  indicates  that  the monitor is on and  fully functional. An amber light  indicates  power save mode.
 
Using the On-Screen Display (OSD) MenuNOTE:  If you change  the settings and  then  either  proceed to  another menu,  or exit  the OSD menu,  the monitor automatically saves the changes.  The  changes are also  saved  if you change  the settings and  then  wait  for the OSD menu  to  disappear.
1. Press  any key  to  launch the OSD menu  and  press  
 to  display  the main menu.
Main Menu for Analog (VGA) Input
Or
Main Menu for non Analog (non VGA) Input
 
 
						

							Dell IN2020/IN2020M Flat Panel Monitor Users Guide
file:///C|/Users/santhosh_v/Desktop/UG_en/operate.htm[3/27/2013 12:21:03 PM]
 NOTE: Auto Adjust  is only  available  when  you are using  the analog  (VGA) connector.
2.  Press  the  and   buttons to  move  between  the setting  options.  As you move  from  one  icon to  another,  the option name is highlighted.  See the table for a  complete  list of all the options available  for the monitor.
3.  Press  the  button once  to  activate the highlighted option.  
4.  Press  the  and   buttons to  select the desired parameter.
5. Press  the    button  to  enter the slide bar and  then  use the    and   buttons,  according to  the indicators on the menu,  to  make  your  changes.  
6. Press  the 
 button  to  return  to  the main menu  or exit  the OSD menu.
Icon Menu and Submenus Description
 
 
 
 
 Brightness/Contrast
 
BrightnessContrast
Back
   
 Allows  you to  adjust  the brightness and  contrast.
Brightness adjusts the luminance of the backlight.
Press  the  
 button to  increase  the brightness and   Press  the  button to  decrease the brightness (min  0 ~ max 100).
Adjust  the Brightness first, and  then  adjust  the Contrast  only  if further adjustment is necessary.
Press  the 
 button to  increase  contrast  and  press  the   button to  decrease contrast  (min  0 ~ max 100). 
The  Contrast  function adjusts the degree of difference between  the darkest  and  lightest areas on the monitor screen.
Press  the 
 button  to  go back  to  or exit  the main menu.
 
 
  Auto Adjust
 
 Even though  your  computer  recognizes your  monitor on startup, the Auto Adjustment function optimizes the display  settings for use with your  particular  setup.
 
NOTE:
 In most cases,  Auto Adjust  produces the best image for your  configuration.   
  Input Source
  Auto SelectThe  Input Source menu  is to  used to  select between  different video  signals  that  may be connected to  your  monitor.
Scan for Sources. Push  to  scan  for available  input signals.
 
						

							Dell IN2020/IN2020M Flat Panel Monitor Users Guide
file:///C|/Users/santhosh_v/Desktop/UG_en/operate.htm[3/27/2013 12:21:03 PM]VGA
DVI-DBack
     Select VGA input when  you are using  the analog  (VGA) connector. 
Push 
 to  select the VGA input source.
Select DVI-D  input when  you are using  the Digital (DVI) connector.  Push 
 to  select the DVI input source.
Push  the
 button   to  go back  to  or exit  the main menu.
 
 
 
  Color  Settings
Input Color  FormatMode Selection
Preset  Modes
VGA  input Standard
Multimedia
Game
Warm
Cool
Custom (RGB)
Video input MovieGame
Sports
Nature Hue
Saturation
Demo Mode Use  the color  settings to  adjust  the Image mode and  color  format.
Allows  you to  set  the color  format.
Allows  you to  set  the display  mode to  Graphics or Video. If  your  computer  is connected to  your  monitor,  choose Graphics. If  a  DVD,  STB,  or VCR is connected to  your  monitor,  choose Video.
 
Mode  suitable for desktop applications.
Mode  for multimedia  applications, e.g., video  playback.
Mode  suitable for gaming applications.
Select warm mode to  obtain a  red tint. This color  setting  is typically used for color -intensive  applications  (photograph image editing,  multimedia, movies,  etc.).
Select cool  mode to  obtain a  bluish tint. This color  setting  is typically used for text based applications  (spreadsheets, programming, text editors, etc.).
Use  the 
 or  buttons to  increase  or decrease each  of the three colors (R,  G, B) independently, in single -digit  increments,  from  0 to  100.
 
Mode  suitable for movie playback.
Mode  suitable for game applications.
Mode  suitable for sports  scenes.
Mode  suitable for nature scenes.
This feature  can  make  the video  image color  shift  from  green to  purple. Use  this feature  to  adjust  the skin  tone.  Use  
 or  buttons to  adjust  the hue  from  0  to  100. increases  the green hue  in the image increases  the purple  hue  in the image
NOTE:  Hue adjustment is only  available  for video  input.
Allows  you to  adjust  the color  saturation  of the video  image.  Use  
 or  buttons to  adjust  the saturation  from  0  to  100 makes video  image looks  monochrome makes video  image looks  colorful
NOTE:  Saturation adjustment is only  available  for video  input.
Vertically splits  the screen into two segments. The  left  half  of the screen in the normal  mode and  the right  half  of the screen is displayed in the color  enhanced  mode.