Dell G2410h Users Guide

							1. P ress and hold the stand release button.    
2. Lift the stand up and away from the monitor .   
Wall Mounting (Optional)  
 
(Screw dimension: M4 x 10mm).   
Refer to the instructions that come with the VESA compatible base mounting kit.   
1. Place the monitor panel on a soft cloth or cushion on stable flat table.    
2. Remove the stand   
3. Use a screwdriver to remove the four screws securing the plastic cover.    
4. Attach the mounting bracket from the wall mounting kit to the LCD.    
5. Mount the LCD on the wall by following the instructions that came with the base mounting kit.    
Back to Contents Page      NOTE:   For use only with UL Listed Wall Mount Bracket with minimum weight/load bearing capacity of 4.36kg .    
						

							Back to Contents Page    
 
Troubleshooting  
 
   Troubleshooting Your Monitor  
   Common Problems  
   Product - Specific Problems  
Troubleshooting Your Monitor  
Self - Test Feature Check  
Your monitor provides a self - test feature that allows you to check whether your monitor is functioning properly. If your monitor and computer are properly 
connected but the monitor screen remains dark, run the monitor self - test by performing the following steps:   
1. Turn off both your computer and the monitor.   
2. Unplug the video cable from the back of the computer. To ensure proper Self - Test operation, remove both Digital (white connector) and the Analog (blue 
connector) cables from the back of computer.   
3. Turn on the monitor. 
   
4. This box also appears during normal system operation, if the video cable becomes disconnected or damaged.   
5. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor.   
If your monitor screen remains blank after you use the previous procedure, check your video controller and computer, because your monitor is functioning 
properly.  
Built - in Diagnostics  
Your monitor has a built - in diagnostic tool that helps you determine if the screen abnormality you are experiencing is an inherent problem with your monitor, or 
with your computer and video card.  
To run the built - in diagnostics:  
1. Ensure that the screen is clean (no dust particles on the surface of the screen).    
2. Unplug the video cable(s) from the back of the computer or monitor. The monitor then goes into the self - test mode.    
3. Press and hold the  B  and  E  buttons on the front panel, simultaneously for 2 seconds. A gray screen appears.    CAUTION:  Before you begin any of the procedures in this section, follow the  Safety Instructions  
The floating dialog box should appear on - screen (against a black background) if the monitor cannot sense a video signal and is working correctly. 
While in self - test mode, the power LED remains blue. Also, depending upon the selected input, one of the dialogs shown below will continuously scroll 
through the screen.  
  or   
NOTE:  You can run the built - in diagnostics only when the video cable is unplugged and the monitor is in  self - test mode .  
						

							4. Carefully inspect the screen for abnormalities.    
5. Press the  E  button on the front panel again. The color of the screen changes to red.    
6. Inspect the display for any abnormalities.    
7. Repeat steps 5 and 6 to inspect the display in green, blue, and white colored screens.    
The test is complete when the white screen appears. To exit, press the  E  button again.  
If you do not detect any screen abnormalities upon using the built - in diagnostic tool, the monitor is functioning properly. Check the video card and computer.  
Common Problems  
The following table contains general information about common monitor problems you might encounter and the possible solutions.   A Ambient light Sensor Lens
B Shortcut Key 1 / Up button
C Shortcut Key 2 / Down button
D OSD menu / OK button
E Back / Exit  button  
F Power button (with power light indicator)
Common Symptoms   What You 
Experience   Possible Solutions  
No Video/ Power LED off No picture l Ensure that the video cable connecting the monitor and the computer is properly connected and secure.    
l Verify that the power outlet is functioning properly by using any other electrical equipment.    
l Ensure that the power button is depressed fully .    
No Video/ Power LED on No picture 
or no 
brightness l Increase brightness & contrast controls using the OSD.    
l Perform monitor self - test feature check.    
l Check for bent or broken pins in the video cable connector.    
l Run the built - in diagnostics.   
Poor Focus Picture is 
fuzzy, 
blurry, or 
ghosting l Perform Auto Adjust using the OSD.    
l Adjust the Phase and Pixel Clock controls using the OSD.    
l Eliminate video extension cables.    
l R eset the monitor to Factory Settings.    
l Change the video resolution to the correct aspect ratio (16:10) for G2210, (16:9) for G2410    
Shaky/Jittery Video Wavy 
picture or 
fine 
movement l Perform Auto Adjust using the OSD.    
l Adjust the Phase and Pixel Clock controls using the OSD.    
l R eset the monitor to Factory Settings.    
l Check environmental factors.    
l Relocate the monitor and test it in another room.    
Missing Pixels LCD screen 
has spots l Cycle power on - off.    
l Pixel that is permanently off is a natural defect that can occur in LCD technology .    
l Run the built - in diagnostics.   
Stuck - on Pixels LCD screen 
has bright 
spots l Cycle power on - off.    
l Pixel that is permanently off is a natural defect that can occur in LCD technology .    
l Run the built - in diagnostics.   
Brightness Problems Picture too 
dim or too 
bright l Reset the monitor to Factory Settings.    
l Auto Adjust using the OSD.    
l Adjust brightness & contrast controls using the OSD.    
l Keep any object clear from the intelligent ambient light sensor.   
Geometric Distortion Screen not 
centered 
correctly l Reset the  monitor to Factory Settings.    
l Auto Adjust using the OSD.    
l Adjust brightness & contrast controls using the OSD.    
NOTE:  When using 2: DVI - D, the positioning adjustments are not available.  
Horizontal/Vertical Lines Screen has 
one or more 
lines l Reset the monitor to Factory Settings.    
l Perform Auto Adjust using the OSD.    
l Adjust Phase and Pixel Clock controls using the OSD.    
l Perform monitor self - test feature check and determine if these lines are also in self - test mode.    
l Check for bent or broken pins in the video cable connector.    
l Run the built - in diagnostics.   
NOTE:  When using 2: DVI - D, the Pixel Clock and Phase adjustments are not available.  
Synchronization Problems Screen is  l Reset the monitor to Factory Settings.      
						

							scrambled 
or appears 
torn l Perform Auto Adjust using the OSD.    
l Adjust Phase and Pixel Clock controls using the OSD.    
l Perform monitor self - test feature check to determine if scrambled screen appears in self - test mode.    
l Check for bent or broken pins in the video cable connector.    
l Restart the computer  in the  safe mode .    
Safety Related Issues Visible signs 
of smoke or 
sparks l Do not perform any troubleshooting steps.   
l Contact Dell immediately.   
Intermittent Problems Monitor 
malfunctions 
on & off l Ensure that the video cable connecting the monitor to the computer is connected properly and is secure.    
l Reset the monitor to Factory Settings.    
l Perform monitor self - test feature check to determine if the intermittent problem occurs in self - test mode.    
Missing Color Picture does 
not have 
color l Perform monitor self - test feature check.    
l Ensure that the video cable connecting the monitor to the computer is connected properly and is secure.    
l Check for bent or broken pins in the video cable connector.    
Wrong Color Picture color 
is not good l Change the Color Setting Mode in the Color Settings OSD to Graphics or Video depending to the 
application.   
l Try different Color Preset Settings in Color Settings OSD. Adjust R/G/B value in Color Settings OSD if the 
Color Management is turned off.   
l Change the Input Color Format to PC RGB or YPbPr in the Advance Setting OSD.   
l Run the built - in diagnostics.   
Image retention  from a static 
image left on the monitor for a 
long period of time Faint 
shadow 
from the 
static image 
displayed 
appears on 
the screen l Use the Power Management feature to turn off the monitor at all times when it is not in use  (for more 
information, see Power Management Modes).   
l Alternatively, use a dynamically changing screensaver.