Dell E2310h Users Guide

   
   
   
   
See  Solving Problems  for more information.  
Setting the Maximum Resolution  
To set the Maximum resolution for the monitor:  
1. Right - click on the desktop and select  Properties .   
2. Select the  Settings  tab.   
3. Set the screen resolution to 1600 x 900 (for E2010H) or 1920 x 1080 (for E2210H/E2310H).   
4. Click  OK .   
If you do not see 1600 x 900 (for E2010H) or 1920 x 1080 (for E2210H/E2310H)as an option, you may need to update your graphics driver. Depending on your...

Tilt  
With the built - in pedestal, you can tilt the monitor for the most comfortable viewing angle.  
 
 
Back to Contents Page  NOTE:   The stand is detached when the monitor is shipped from the factory.   

Back to Contents Page   
Setting Up Your Monitor   
 
E2010H/E2210H/E2310H  Flat Panel Monitor   
Setting the display resolution to1600 x 900 (for E2010H) or 1920 x 1080 (for 
E2210H/E2310H) (Maximum)  
For optimal display performance while using the Microsoft Windows operating systems, set the display resolution to 1600 x900 (for E2010H) or 1920 x 1080 
(for E2210H/E2310H)pixels by performing the following steps:  
1. Right - click on the desktop and click  Properties .  
2. Select the  Settings  tab....

E2010H/E2210H/E2310H  
Information in this document is subject to change without notice.  
2009  
Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.   is strictly forbidden.  
Trademarks used in this text:  Dell  and the  DELL  logo are trademarks of Dell Inc.;   Microsoft and Windows  are either registered trademarks or trademarks of Microsoft Corporation in 
the United States and/or other countries. ENERGY STAR  is a registered trademark of the U.S....

Back to Contents Page    
 
Setting Up the Monitor   
E2010H/E2210H/E2310H  Flat Panel Monitor Users Guide  
   Attaching the Stand  
   Connecting Your Monitor  
   Attaching the Dell Soundbar (Optional)  
   Removing the Stand Base    
  Wall mounting (Optionalyf   
   
Attaching the Stand  
 
   
Connecting Your Monitor  
To connect your monitor to the computer:  
1. Turn off your computer and disconnect the power cable.   
2. Connect either the white (digital DVI - D) or the blue (analog VGA)...

 
Attaching the Dell Soundbar(Optional)  
 
To attach the Soundbar:  
Removing the Stand  
To remove the stand:  
 
1. P ress and hold the stand release button.    
2. Lift the stand up and away from the monitor .   CAUTION:  The Graphics are used for the purpose of illustration only. Appearance of the computer may vary.
NOTICE:  Do not use with any device other than the Dell Soundbar. 
1.  Working from the rear of the monitor, attach Soundbar by aligning the two slots with the two tabs along the bottom...

Wall Mounting (Optional)  
 
(Screw dimension: M4 x 10mm).   
Refer to the instructions that come with the VESA compatible base mounting kit.   
1. Place the monitor panel on soft cloth or cushion on stable flat table.    
2. Remove the stand   
3. Use a screwdriver to remove the four screws securing the plastic cover.    
4. Attach the mounting bracket from the wall mounting kit to the LCD.    
5. Mount the LCD on the wall by following the instructions that come with the base mounting kit.    
Back to...

Back to Contents Page    
 
Troubleshooting  
 
E2010H/E2210H/E2310H  Flat Panel Monitor   
   Self - Test  
   Common Problems  
   Product Specific Problems  
   
Self - Test  
Your monitor provides a self - test feature that allows you to check whether your monitor is functioning properly. If your monitor and computer are properly 
connected but the monitor screen remains dark, run the monitor self - test by performing the following steps:   
1. Turn off both your computer and the monitor.   
2....

A. Ensure that the screen is clean (no dust particles on the surface of the screen).   
B. Unplug the video cable from the back of the computer or monitor. The monitor then goes into the self - test mode.   
C. Press and hold the 1st and  4th  buttons on the front panel, simultaneously for 2 seconds. A gray screen appears.   
D. Carefully inspect the screen for abnormalities.   
E. Press the  4th  button on the front panel again. The color of the screen changes to red.   
F. Inspect the display for any...

   
Product Specific Problems  
Back to Contents Page   Settings OSD if the Color Management is turned off.  
l Change the Input Color Format to PC RGB or YPbPr in the Advance Setting OSD.  
l Run the built - in diagnostics.   
Image retention from a static 
image left on the monitor for a 
long period of time Faint shadow from the static 
image displayed appears on 
the screen l Use the Power Management feature to turn off the monitor at all times when not in use  
(for more information, see  Power...