Dell E1910h Users Guide

 
 
Back to Contents Page  NOTE:   The stand is detached when the monitor is shipped from the factory.   

Back to Contents Page   
Setting Up Your Monitor   
 
E1910H  Flat Panel Monitor   
Setting the display resolution to  1366X768 ( Maximum)  
For optimal display performance while using the Microsoft Windows operating systems, set the display resolution to 1366 x 768 pixels by performing the 
following steps:  
1. Right - click on the desktop and click  Properties .  
2. Select the  Settings  tab.  
3. Move the slider - bar to the right by pressing and holding left - mouse button and adjust the screen...

E1910H  
Information in this document is subject to change without notice.  
2009  
Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.   is strictly forbidden.  
Trademarks used in this text:  Dell  and the  DELL  logo are trademarks of Dell Inc.;   Microsoft and Windows  are either registered trademarks or trademarks of Microsoft Corporation in 
the United States and/or other countries. ENERGY STAR  is a registered trademark of the U.S. Environmental...

Back to Contents Page    
 
Setting Up the Monitor   
E1910H  Flat Panel Monitor Users Guide  
   Attaching the Stand  
   Connecting Your Monitor  
   Removing the Stand Base     
   Attaching the Dell Soundbar (Optional)  
   Removing the Stand for VESA wall mount  
   
Attaching the Stand  
 
 
   
Connecting Your Monitor  
To connect your monitor to the computer:  
1. Turn off your computer and disconnect the power cable.   
2. Connect the blue display connector cable to the corresponding video port...

 
Removing the Stand Base   
   
Attaching the Dell Soundbar(Optional)  CAUTION:  The Graphics are used for the purpose of illustration only. Appearance of the computer may vary.
   
 
To remove the base of the stand from the monitor:  
1. Place  the monitor panel on soft cloth or cushion on a stable flat table.  
2. Press and hold the release latch, while pulling the base of the stand away from the 
monitor.  

 
To attach the soundbar:  
   
   
Removing the Stand for VESA Wall Mount  
 
Back to Contents Page    
    NOTICE:  Do not use with any device other than the Dell Soundbar. 
1.  Working from the back of the monitor, attach Soundbar by aligning the two slots with the two tabs along the bottom of the monitor.
2.  Slide the Soundbar to the left until it snaps into place.
3.  Connect the Soundbar with the DC power connector from the Soundbar Power Adaptor.
4.  Insert the mini stereo plug from the back of...

Back to Contents Page    
 
Troubleshooting  
 
E1910H  Flat Panel Monitor   
   Self - Test  
   Common Problems  
   Product Specific Problems  
   
Self - Test  
Your monitor provides a self - test feature that allows you to check whether your monitor is functioning properly. If your monitor and computer are properly 
connected but the monitor screen remains dark, run the monitor self - test by performing the following steps:   
1. Turn off both your computer and the monitor.   
2. Unplug the video...

To run the built - in diagnostics:  
1. Ensure that the screen is clean (no dust particles on the surface of the screen).   
2. Unplug the video cable from the back of the computer or monitor. The monitor then goes into the self - test mode.   
3. Press and hold the 1st and 4th buttons on the front panel, simultaneously for 2 seconds. A gray screen appears.   
4. Carefully inspect the screen for abnormalities.   
5. Press the 4th button on the front panel again. The color of the screen changes to red....

   
Product Specific Problems  
Back to Contents Page  Wrong Color Picture color not good l Change the Color Setting Mode in the Color Settings OSD to Graphics or Video 
depending on the application.   
l Try different Color Preset Settings in Color Settings OSD. Adjust R/G/B value in Color 
Settings OSD if the Color Management is turned off.  
l Change the Input Color Format to PC RGB or YPbPr in the Advance Setting OSD.  
l Run the built - in diagnostics.   
Image retention from a static 
image left on...