Home > Dell > System > Dell Drac 5 User Guide

Dell Drac 5 User Guide

Here you can view all the pages of manual Dell Drac 5 User Guide. The Dell manuals for System are available online for free. You can easily download all the documents as PDF.

Page 311

RACADM Subcommand Overview311
Restrictions
The Hostname and OS Name fields in the getsysinfo output display accurate 
information only if Dell OpenManage is installed on the managed system. If 
OpenManage is not installed on the managed system, these fields may be blank 
or inaccurate. 
getractime
 NOTE: To use this command, you must have Log In DRAC 5 permission. 
Table A-16 describes the getractime subcommand.
Synopsis
racadm getractime [-d]
Description
With no options, the getractime subcommand...

Page 312

312RACADM Subcommand Overview
Supported Interfaces
•Local RACADM
• Remote RACADM
• Telnet/SSH/Serial RACADM
ifconfig
 NOTE: To use this command, you must have Execute Diagnostic Commands or 
Configure DRAC 5 permission.
Table A-17 describes the ifconfig subcommand.
Synopsis
racadm ifconfig
netstat
 NOTE: To use this command, you must have Execute Diagnostic Commands 
permission.
Table A-18 describes the netstat subcommand.
Synopsis
racadm netstat
Table A-17. ifconfig
Subcommand Definition...

Page 313

RACADM Subcommand Overview313
Supported Interfaces
• Remote RACADM
• Telnet/SSH/Serial RACADM
ping
 NOTE: To use this command, you must have Execute Diagnostic Commands or 
Configure DRAC 5 permission.
Table A-19 describes the ping subcommand.
Synopsis
racadm ping 
Supported Interfaces
• Remote RACADM
• Telnet/SSH/Serial RACADM
Table A-19. ping
Subcommand Definition
pingVerifies that the destination IP address is reachable from the 
DRAC 5 with the current routing-table contents. A destination 
IP...

Page 314

314RACADM Subcommand Overview
setniccfg
 NOTE: To use the setniccfg command, you must have Configure DRAC 5 
permission.
Table A-20 describes the setniccfg subcommand.
 NOTE: The terms NIC and Ethernet management port may be used 
interchangeably.
Synopsis
racadm setniccfg -d 
racadm setniccfg -s [  ]
racadm setniccfg -o [  ]
Description
The setniccfg subcommand sets the controller IP address.
•The 
-d option enables DHCP for the Ethernet management port (default 
is DHCP enabled).
•The 
-s option...

Page 315

RACADM Subcommand Overview315
Output
The setniccfg subcommand displays an appropriate error message if the 
operation is not successful. If successful, a message is displayed. 
Supported Interfaces
•Local RACADM
• Remote RACADM
• Telnet/SSH/Serial RACADM
getniccfg
 NOTE: To use the getniccfg command, you must have Log In To DRAC 5 permission.
Table A-21 describes the setniccfg and getniccfg subcommands.
Synopsis
racadm getniccfg
Description
The getniccfg subcommand displays the current Ethernet...

Page 316

316RACADM Subcommand Overview
Gateway = 192.168.0.1
Supported Interfaces
•Local RACADM
• Remote RACADM
• Telnet/SSH/Serial RACADM
getsvctag
 NOTE: To use this command, you must have Log In To DRAC 5 permission.
Table A-22 describes the getsvctag subcommand.
Synopsis
racadm getsvctag
Description
The getsvctag subcommand displays the service tag of the host system.
Example
Ty p e  getsvctag at the command prompt. The output is displayed as follows: 
Y76TP0G
The command returns 0 on success and nonzero on...

Page 317

RACADM Subcommand Overview317
racdump
 NOTE: To use this command, you must have Debug permission. 
Table A-23 describes the racdump subcommand.
Synopsis
racadm racdump
Description
The racdump subcommand provides a single command to get dump, status, 
and general DRAC 5 board information.
The following information is displayed when the 
racdump subcommand is 
processed:
• General system/RAC information
•Coredump
• Session information
• Process information
• Firmware build information
Supported Interfaces...

Page 318

318RACADM Subcommand Overview
racreset
 NOTE: To use this command, you must have Configure DRAC 5 permission. 
Table A-24 describes the racreset subcommand.
 CAUTION: When you issue a racreset subcommand, the DRAC may require up to 
one minute to return to a usable state. 
Synopsis
racadm racreset [hard | soft]
Description
The racreset subcommand issues a reset to the DRAC 5. The reset event is 
written into the DRAC 5 log.
A hard reset performs a deep reset operation on the RAC. A hard reset should...

Page 319

RACADM Subcommand Overview319
Examples
•racadm racreset
Start the DRAC 5 soft reset sequence.
•racadm racreset hard
Start the DRAC 5 hard reset sequence.
Supported Interfaces
•Local RACADM
• Remote RACADM
• Telnet/SSH/Serial RACADM
racresetcfg
 NOTE: To use this command, you must have Configure DRAC 5 permission. 
Table A-26 describes the racresetcfg subcommand.
Synopsis
racadm racresetcfg
Supported Interfaces
•Local RACADM
• Remote RACADM
• Telnet/SSH/Serial RACADM
Table A-26. racresetcfg
Subcommand...

Page 320

320RACADM Subcommand Overview
Description
The racresetcfg command removes all database property entries that have been 
configured by the user. The database has default properties for all entries that 
are used to restore the card back to its original default settings. After resetting 
the database properties, the DRAC 5 resets automatically.
 CAUTION: This command deletes your current RAC configuration and resets the 
RAC and serial configuration to the original default settings. After reset, the...
Start reading Dell Drac 5 User Guide

Related Manuals for Dell Drac 5 User Guide

All Dell manuals