Dell Alienware Aurora R2 Service Manual
Have a look at the manual Dell Alienware Aurora R2 Service Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 327 Dell manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
081081/ CHAPTER 16: RIGHT SIDE-PANEL(S) Replacing the Right Side-Panel(s) Follow the instructions in “Before You Begin” on page 1. 6. Align the right bottom-panel to the bottom of the computer and slide it into 2. position. Slide the lighting board into position and replace the two screws that secure 3. the lighting board to the chassis. Connect the lighting-board cable to the connector on the master I/O board. 4. Slide the right top-panel into position.5. Place the chassis on its side.6. Replace the three screws that secure the right side-panel(s) to the chassis.7. Replace the power-supply cover (see “Replacing the Power Supply“ on 8. page 59). Replace the hard-drive fan assembly (see “Replacing the Hard-Drive Fan 9. Assembly” on page 43). Replace the drive-bay shroud (see “Replacing the Drive-Bay Shroud” on 10. page 19). Close the PCI shroud (see “Closing the PCI Shroud“ on page 11. 18). Replace the left side-panel (see “Replacing the Left Side-Panel“ on page 12. 11). Connect your computer and devices to electrical outlets and then turn 13. them on. Slide and pull the right bottom-panel away from the chassis.13. 1 1right bottom-panel
CHAPTER 17: ACTIVE-VENTING ASSEMBLY 082082/ CHAPTER 17: ACTIVE VENTING ASSEMBLY CHAPTER 17: ACTIVE-VENTING ASSEMBLY
083083/ CHAPTER 17: ACTIVE-VENTING ASSEMBLY Active-Venting Assembly WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. WARNING: Do not operate your computer with any cover(s) (including computer covers, bezels, filler brackets, front-panel inserts, etc.) removed. WARNING: To guard against electrical shock, always unplug your computer from the electrical outlet before removing the side panel(s). CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is not covered by your warranty.
084084/ CHAPTER 17: ACTIVE-VENTING ASSEMBLY 1 1screw Removing the Active-Venting Assembly NOTE: Active-venting assembly is available only in Alienware Aurora ALX. Follow the instructions in “Before You Begin” on page 1. 6. Remove the left side-panel (see “Removing the Left Side-Panel“ on page 2. 11). Open the PCI shroud (see “Opening the PCI Shroud“ on page 3. 18). Remove the drive-bay shroud (see “Removing the Drive-Bay Shroud” on 4. page 19). Remove the screw that secures the right top-panel to the chassis.5.
085085/ CHAPTER 17: ACTIVE-VENTING ASSEMBLY Place the chassis in an upright position.8. Remove the right top-panel.9. 1 1right top-panel Remove the top lighting-board (see “Removing the Top Lighting-Board” on 6. page 76). Remove the ten screws that secure the active-venting assembly to the 7. chassis. 1 1screws (10)
086086/ CHAPTER 17: ACTIVE-VENTING ASSEMBLY Remove the two screws that secure the top panel to the chassis.10. Lift the top panel away from the chassis.11. Remove the three screws that secure the active-venting assembly to the 12. chassis. Disconnect the cables that connect the active-venting assembly to the 13. connectors on the master I/O board. Lift the active-venting assembly away from the chassis.14. 2 3 4 1 1screws (3) 2active-venting assembly 3top panel4top-panel screws (2)
087087/ CHAPTER 17: ACTIVE-VENTING ASSEMBLY Replace the screw that secures the right top-panel to the chassis.10. Replace the drive-bay shroud (see “Replacing the Drive-Bay Shroud” on 11. page 19). Close the PCI shroud (see “Closing the PCI Shroud“ on page 12. 18). Replace the left side-panel (see “Replacing the Left Side-Panel“ on page 13. 11). Connect your computer and devices to electrical outlets and then turn 14. them on. Replacing the Active-Venting Assembly Follow the instructions in “Before You Begin” on page 1. 6. Place the active-venting assembly on the top of the chassis.2. Connect the active-venting assembly cables to the connectors on the 3. master I/O board. Replace the three screws that secure the active-venting assembly to the 4. chassis. Align the top panel with the slots in the chassis and replace the two screws 5. that secure the top panel to the chassis. Replace the right top-panel.6. Lay the chassis on its side.7. Replace the ten screws that secure the active-venting assembly to the top 8. of the chassis. Replace the top lighting-board (see “Replacing the Top Lighting-Board” on 9. page 76).
CHAPTER 18: FRONT BEZEL 088088/ CHAPTER 18: FRONT BEZEL CHAPTER 18: FRONT BEZEL
089089/ CHAPTER 18: FRONT BEZEL Front Bezel WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. WARNING: Do not operate your computer with any cover(s) (including computer covers, bezels, filler brackets, front-panel inserts, etc.) removed. WARNING: To guard against electrical shock, always unplug your computer from the electrical outlet before removing the side panel(s). CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is not covered by your warranty.
090090/ CHAPTER 18: FRONT BEZEL 1 1screws (7) Removing the Front Bezel Follow the instructions in “Before You Begin” on page 1. 6. Remove the left side-panel (see “Removing the Left Side-Panel“ on page 2. 11). Open the PCI shroud (see “Opening the PCI Shroud“ on page 3. 18). Remove the drive-bay shroud (see “Removing the Drive-Bay Shroud” on 4. page 19). Remove the right side-panel(s) (see “Removing the Right Side-Panel(s)” on 5. page 79). Remove the seven screws that secure the front bezel to the chassis.6. Disconnect the front bezel cables from the connectors on the master I/O 7. board. Note the cable routing before disconnecting the cables.