Dell 3007wfp Users Guide

							 
Using the Front Panel Buttons  
Use the buttons on the front of the monitor to adjust the image settings.   
Using the OSD  
  
   
 
Down ( - )  and Up (+)  Touch  -   or + to activate the on - screen display (OSD).
Use these buttons to decrease/increase the brightness ranges.  
 
Power Button and 
Indicator Use the  power button to turn the monitor on and off. 
The blue light  indicates the monitor is on and fully functional. An amber light indicates power save mode.  
   
NOTE:  If  you make an adjustment, the monitor automatically saves any adjustments you have made. 
1. Touch  -   or + to activate the on - screen display (OSD).
2.  Touch  -   and + button to select the desired parameter.  
Icon Brightness bar Description
  Brightness   Brightness adjusts the  luminance of the monitor. 
Press  the  +  button to increase luminance and press  the  -  button to decrease luminance (min 0 ~ max 20).   
   
NOTE:  OSD generate from PC application F/W through the upstream port of USB to make sure the USB cable connect well.  
						

							Using the Dell Soundbar (Optional)  
The Dell Soundbar is a four - speaker, two - channel speaker that can be attached to your monitor.  Located on the Soundbar are a: Rotary volume and on/off 
control to adjust the overall system level, a green LED for power indication, and two audio headset jacks.  
 
Soundbar Attachment to the Monitor  
 
Back to Contents Page  
    1. Attach mechanism 
2.   Power/volume control 
Power indicator 
4.   Headphone connectors 
NOTICE: Do not use the soundbar power connector with any other device.
1. Attach the Soundbar by aligning the two slots on the Soundbar with the two tabs on the bottom of the monitor.
2.   Slide the Soundbar to the left until it snaps in to place.
Plug in the power cord from the Soundbar in to the connector on the back of the monitor.
4.   Insert the green stereo plug from the Soundbar in to your computers audio output connector.  
						

							Back to Contents Page    
 
Solving Problems   
- HC Flat Panel Monitor Users Guide  
   General Problems  
   Product Specific Problems  
   USB Problems  
   Troubleshooting Your Soundbar  
   
   
General Problems  
The following table contains general information about common monitor problems you might encounter.   
Product Specific Problems  CAUTION:  Before you begin any of the procedures in this section, follow the  safety instructions .  
COMMON SYMPTOMS   WHAT YOU EXPERIENCE   POSSIBLE SOLUTIONS  
No Video/ Power LED off No picture or monitor is dead l Check connection integrity at both ends of the video cable.   
l Ensure the monitor and computer are plugged in to a working electrical outlet. 
Connecting Your Monitor    
l Ensure power button is depressed fully.   
No Video/ Power LED on No picture or no brightness l Increase brightness controls.   
l Perform monitor self - test feature check.   
l Check for bent or broken pins.   
l Re - boot your computer and monitor.   
Poor Focus Picture is fuzzy, blurry, or ghosting l Eliminate video extension cables.   
l Perform monitor reset.   
l Lower video resolution or increase font size.   
Shaky/Jittery Video Wavy picture or fine movement l Perform monitor reset.   
l Check environmental factors.   
l Relocate and test in other room.   
Missing Pixels LCD screen has spots l Cycle power on - off.   
l These are pixels that are permanently off and is a natural defect that occurs in 
LCD technology.   
Brightness Problems Picture too dim or too bright l Perform monitor reset.  
l Adjust brightness controls.   
Horizontal/Vertical Lines Screen has one or more lines l Perform monitor reset.   
Sync Problems Screen is scrambled or appears torn l Perform monitor reset.  
l Start in the safe mode.   
LCD Scratched Screen has scratches or smudges l Turn monitor off and clean the screen.   
l For cleaning instruction, see  Caring for Your Monitor .   
Safety Related Issues Visible signs of smoke or sparks l Do not perform any troubleshooting steps.   
l Monitor needs to be replaced.   
Intermittent Problems Monitor malfunctions on & off l Ensure monitor is in proper video mode.   
l Ensure video cable connection to computer and to the panel is secure.   
l Perform monitor reset.  
Image Retention (from a 
static imageyf  Faint Shadow from the static image 
displayed appears on the 
screen             l Use the Power Management feature to turn off the monitor at all times when not 
in use. Alternatively, use a dynamically changing screensaver left on the 
monitor for a long period of time.   
SPECIFIC SYMPTOMS WHAT YOU EXPERIENCE POSSIBLE SOLUTIONS
Unable to view any image / Only 
2560 x 1600 resolution is  Blank image or low 
resolution display l Ensure that the recommended graphics card that supports Dual DVI out is 
installed.     
						

							USB Problems  
Troubleshooting Your Soundbar  
Back to Contents Page  
    available. 
Unable to view Brightness OSD 
while adjusting brightness of the 
monitor Monitor brightness changes 
however no OSD appears l If you are using a Microsoft ®  Windows ®  operation system, install application tool 
provided in the CD. See installing the Utility Tool (Microsoft ®  Windows ®  Operation 
System) for more information.   
Cannot adjust the monitor with 
the buttons on the front panel No change in monitor 
brightness settings l Turn the monitor off and unplug the power cord. Then plug the power cord back 
and turn the power on.   
SPECIFIC SYMPTOMS WHAT YOU EXPERIENCE POSSIBLE SOLUTIONS
USB port is not working USB peripherals are not working l Check that your monitor is powered ON.   
l Reconnect the upstream cable to your computer.   
l Reconnect the USB peripherals to downstream 
connector.    
l Turn off and then turn on the monitor again.   
High Speed USB 2.0 interface is 
slow. High Speed USB 2.0 peripherals working slowly or not 
at all. l Check that your computer is USB 2.0 compatible.   
l Verify USB 2.0 source on your computer.   
l Reconnect the upstream cable to your computer.   
l Reconnect the  USB peripherals to downstream 
connector.    
COMMON 
SYMPTOMS   WHAT YOU EXPERIENCE   POSSIBLE SOLUTIONS  
No Sound No power to Soundbar  -  the 
power indicator is off.   
(built - in DC power supply. i.e. 
3007WFP - HC ) l Turn the Power/Volume knob on the Soundbar clockwise to the middle position; check if the 
power indicator (green LED) on the front of the Soundbar is illuminated.   
l Confirm that the power cable from the Soundbar is plugged into the monitor.   
l Confirm that the monitor has power.   
No Sound Soundbar has power  -  power 
indicator is on. l Plug the audio line - in cable into the computers audio out jack.   
l Set all Windows volume controls to their maximum.   
l Play some audio content on the computer (i.e. audio CD, or MP3).   
l Turn the Power/Volume knob on the Soundbar clockwise to a higher volume setting.   
l Clean and reseat the audio line - in plug.   
l Test the Soundbar using another audio source (i.e. portable CD player).   
Distorted Sound Computers sound card is used 
as the audio source. l Clear any obstructions between the Soundbar and the user.   
l Confirm that the audio line - in plug is completely inserted into the jack of the sound card.   
l Set all Windows volume controls to their midpoints.   
l Decrease the volume of the audio application.   
l Turn the Power/Volume knob on the Soundbar counter - clockwise to a lower volume setting.   
l Clean and reseat the audio line - in plug.   
l Troubleshoot the computers sound card.   
l Test the Soundbar using another audio source (i.e. portable CD player).   
Distorted Sound Other audio source is used. l Clear any obstructions between the Soundbar and the user.   
l Confirm that the audio line - in plug is completely inserted into the jack of the audio source.   
l Decrease the volume of the audio source.   
l Turn the Power/Volume knob on the Soundbar counter - clockwise to a lower volume setting.   
l Clean and reseat the audio line - in plug.   
Unbalanced Sound 
Output Sound from only one side of 
Soundbar l Clear any obstructions between the Soundbar and the user.   
l Confirm that the audio line - in plug is completely inserted into the jack of the sound card or 
audio source.   
l Set all Windows audio balance controls (L - R) to their midpoints.   
l Clean and reseat the audio line - in plug.   
l Troubleshoot the computers sound card.   
l Test the Soundbar using another audio source (i.e. portable CD player).   
Low Volume Volume is too low. l Clear any obstructions between the Soundbar and the user.   
l Turn the Power/Volume knob on the Soundbar clockwise to the maximum volume setting.   
l Set all Windows volume controls to their maximum.   
l Increase the volume of the audio application.   
l Test the Soundbar using another audio source (i.e. portable CD player).     
						

							Back to Contents Page    
 
Using Your Adjustable Monitor Stand   
- HC Flat Panel Monitor Users Guide  
   Organizing Your Cables  
   Using the Tilt, Swivel, and Height Adjustment   
Organizing Your Cables  
 
After attaching all necessary cables to your monitor and computer, (See  Connecting Your Monitor  for cable attachment,) use the cable holder to neatly 
organize all cables as shown above.   
Using the Tilt, Swivel, and Height Adjustment  
You can adjust your monitor to best fit your viewing needs using the Tilt, Swivel, and Height Adjustment options.  
 
You can adjust the stand vertically, up to 3.54 inches (90mm) using the stand lock/release button. Press the stand lock/release button on the back of the 
monitor and then lift or lower the stand to the desired position.  
Back to Contents Page  
    NOTE:  Before you move the monitor to a new location, lock the stand by lowering monitor until in clicks in to place.