Dell 2007fp Users Guide

   
 
 
  
Back  
Wide Mode  
H Position  
V Position  
Sharpness  
Zoom  
Horizontal Pan  
 
Pixel Clock  
Phase  
Audio Option  
Display Info  
Display  Reset  
Exit Menu  
   Push    to select Back to go back to the main menu.
Adjust the image ratio as 1:1, aspect or full screen.  
    
  NOTE:   Wide Mode adjustment is not required at optimal preset resolution 1600 x 1200.    
When making changes to either the Horizontal or Vertical settings, no changes will occur to the size of the viewing area: the...

   
   
   
   
    
Back  
Language  
Menu Horizontal Position  
 
Menu Vertical Position  
Menu Timer  
Transparency  
Menu Rotation  
Menu Lock  
Factory Reset  
DCC/CI  
Exit Menu   Push    to select Back to go back to the main menu.
Language option to set the OSD display to one of five languages (English, Espanol, Francais, Deutsch, Japanese).
and    buttons move OSD to the left and right.  
and    buttons move OSD up and down.  
OSD Hold Time: Sets the length of time the OSD will remain active...

   
OSD Warning Messages     
   
   
   
      
Back  
Mode  
When selected PIP
PIP Source  
PIP Position  
PIP Size  
PIP Contrast  
PIP Hue/Tint  
PIP Saturation  
Exit Menu        
 
   
  NOTE:   When using DVI source, the contrast adjustment is not 
available.  
Push    to select Back to go back to the main menu.
There is one mode: PIP (Picture in Picture)    
Use   and   to browse and   to select Off or PIP.  
When PIP on, choose SWAP  to switch the main - screen and sub - screen in PIP mode....

   
                    
   
   
         
   
 
   
See  Solving Problems  for more information.   
   message:  
 
 
 
This means that the monitor cannot synchronize with the signal that it is receiving from the 
computer. Either the signal is too high or too low for the monitor to use.  See  Monitor 
Specifications  for the Horizontal and Vertical frequency ranges addressable by this monitor. 
Recommended mode is 1600 X 1200 @ 60Hz. 
 
You will see the following message before the DDC/CI function is...

Setting the Optimal Resolution   
1. Right - click on the desktop and select  Properties .   
2. Select the  Settings  tab.   
3. Set the screen resolution to  1600 x 1200.    
4. Click  OK .    
If you do not see 1600 x 1200 as an op tion, you may need to update your graphics driver. Depending on your computer, complete one of the following 
procedures.  
 
If you have a Dell™ desktop or portable computer:   
Go to  support.dell.com , enter your service tag, and download the latest driver for your...

 
Back to Contents Page  NOTE: Soundbar Power Connector  -  12V DC output is for optional Dell™ Soundbar only. 
NOTICE:  DO NOT USE WITH ANY DEVICE OTHER THAN DELL Soundbar. 
1. Working from the rear of the monitor, attach Soundbar by aligning the two slots with the two tabs along the bottom rear of the monitor.
2.   Slide the Soundbar to the left until it snaps into place.
Connect the  S oundbar with the DC power connector.
4.   Insert the mini stereo plug from the rear of the Soundbar into the...

Back to Contents Page  
Solving Problems    
 
   Monitor Specific Troubleshooting  
   Common Problems  
   Video Problems  
   Product Specific Problems  
   Universal Serial Bus (USB) Specific Problems  
   Dell™ Soundbar (Optionalyf7URXEOHVKRRWLQg  
   
   
Monitor Specific Troubleshooting  
Self - Test Feature Check  
Your monitor provides a self - test feature that allows you to check whether your monitor is functioning properly. If your monitor and computer are properly 
connected but the monitor...

   
Video Problems  
    Missing Pixels LCD screen has 
spots l Cycle power on - off    
l These are pixels that are permanently off and is a natural defect that occurs in LCD technology    
Stuck - on Pixels LCD screen has 
bright spots l Cycle power on - off    
l These are pixels that are permanently on and is a natural defect that occurs in LCD technology    
Brightness Problems Picture too dim 
or too bright l Perform monitor reset on Factory Reset    
l Auto Adjust via OSD  
l Adjust brightness &...

Product Specific Problems  
   
   
Universal Serial Bus (USB) Specific Problems  
   
 SPECIFIC SYMPTOMS WHAT YOU EXPERIENCE POSSIBLE SOLUTIONS
Screen image is too small Image is centered on screen, but does not fill entire 
viewing area l Perform monitor reset on Factory Reset    
Cannot adjust the monitor with 
the buttons on the front panel OSD does not appear on the screen l Turn the monitor off and unplug the power 
cord and then plug back and power on    
The monitor will not go into 
power saving...

   
Back to Contents Page   l Turn the Power/Volume knob on the Soundbar counter - clockwise to a lower volume setting.   
l Clean and reseat the audio line - in plug.   
l Troubleshoot the computers sound card.   
l Test the Soundbar using another audio source (i.e. portable CD player).   
Distorted Sound Other audio source is used. l Clear any obstructions between the Soundbar and the user.   
l Confirm that the audio line - in plug is completely inserted into the jack of the audio source.   
l...