Dell 1708fp Users Guide
Here you can view all the pages of manual Dell 1708fp Users Guide. The Dell manuals for Monitor are available online for free. You can easily download all the documents as PDF.
Page 11
NOTE: If locked in the down position, 1.Push the monitor down, 2.Press the Lock down / release button on the bottom rear of stand to unlock the monitor. 3.Lift the monitor up and extend the stand to the desired height. NOTICE: Before relocating or moving the monitor to a different location, make sure that the stand is LOCKED DOWN. To lock it down, lower the height of the panel until it clicks and is locked into place.
Page 12
Removing the Stand NOTE: After placing the monitor panel on a soft cloth or cushion, complete the following steps to remove the stand. 1 . Rotate the stand to allow access to the stand release button. 2 . Press the stand release button and lift up the stand and away from the monitor. Back to Contents Page
Page 13
Back to Contents Page Setting Up Your Monitor Dell™ 1708FP Flat Panel Monitor Users Guide Connecting Your Monitor Using the Front Panel Using the OSD Menu Setting the Optimal Resolution Using the Dell Soundbar (Optional) Connecting Your Monitor CAUTION: Before you begin any of the procedures in this section, follow the safety instructions. or
Page 14
1.Turn off your computer and disconnect the power cable. 2. Connect either the white DVI or the blue VGA cables to the connectors on the computer and the monitor. 3. Connect the USB cable that was included with your monitor to the computer and the upstream USB connector on the monitor. Once this cable is connected to the computer and the monitor, you can use the USB connectors on the monitor. 4. Connect any USB devices. 5. Connect the power cables. 6. Turn on your monitor...
Page 15
NOTE: The floating Dell Self-test Feature Check dialog appears on a black background if the monitor cannotsense a video signal. Using the input select button, select the desired input to be tested either Analog Input or Digital Input. Disconnect the video cable from the video card and the Dell Self-test Feature Check dialogue box will appear if the display is operating correctly. or or OSD menu / select The Menu button is used to open and exit the on-screen...
Page 16
Auto Adjust Auto Adjustment button allows the monitor to self-adjust to the incoming video signal. After using Auto Adjustment, you can further tune your monitor by using the Pixel Clock (Coarse), Phase (Fine) controls in the OSD. NOTE: Auto Adjust does not occur if you press the button while there are no active video input signals or attached cables. Power Button and Indicator Use the power button to turn the monitor on and off. The green light indicates the monitor is on...
Page 17
Main Menu for Analog (VGA) Input Main Menu for Digital (DVI) Input or NOTE: Auto Adjust, Positioning and Image Settings are only available when you are using the analog (VGA) connector. 2 . Push the - and + buttons to move between the setting options. As you move from one icon to another, the option name is highlighted. See the table below for a complete list of all the options available for the monitor. 3 . Push the MENU button once to activate the highlighted option....
Page 18
Push the + button to increase luminance and push the - button to decrease luminance (min 0 ~ max 100). Contrast adjusts the degree of difference between darkness and lightness on the monitor screen. Push the + button to increase the contrast and push the - button to decrease the contrast (min 0 ~ max 100). Positioning: Horizontal Vertical Positioning moves the viewing area around on the monitor screen. When making changes to either the Horizontal or Vertical settings, no...
Page 19
Phase (Fine) If satisfactory results are not obtained using the Phase adjustment, use Pixel Clock (Coarse) and then use Phase (fine), again. NOTE: This function may change the width of the display image. Use the Horizontal function of the Position menu to center the display image on the screen. NOTE: When using DVI source, the Image Settings option is not available. Color Settings Normal Preset Blue Preset Red Preset User...
Page 20
Horizontal Position Vertical Position OSD Hold Time OSD Rotation OSD Lock To adjust the horizontal position of the OSD, use the - and + buttons, and move OSD to the left and right. To adjust the vertical position of the OSD, use the - and + buttons, and move OSD down and up. OSD Hold Time: The OSD stays active for as long as it is in use. Adjusting the hold time, sets the length of time the OSD remains active after the last time you pressed a button. Use the...