Dell 1100MP Projector Owners Manual

Using Your Projector21
Language Menu
Press the   or   button on the control 
panel or the 

 or   button on the remote 
control to select the preferred language for 
the OSD. 
Presss the 
 on the control panel or the 
Menu button on the remote control to 
confirm the language selection.
Factory Reset Menu
Select Ye s to reset the projector to its 
factory default settings. Reset items 
include both computer image and video 
image settings.
Computer Image Menu
 NOTE: This menu is only availabl e...

www.dell.com | support.dell.com
22Using Your Projector
HOR. POSITION—Press the  button on the control panel or the 
 button on the 
remote control to adjust the horizontal posi tion of the image to the left and press the 
 button the control panel or the 
 button on the remote control to adjust the 
horizontal position of the image to the right.
VER. POSITION—Press the  button on the control panel or the 
 button on the 
remote control to adjust the vertical po sition of the image down and press the...

Troubleshooting Your Projector23
Troubleshooting Your Projector
If you experience problems with your pr ojector, see the following troubleshooting 
tips. If the problem persists, contact Dell. 
Problem Possible Solution
No image appears on the 
screen
 Ensure that the lens cap is removed and the  projector turned on. 
 Ensure the external graphics port is enabled.  If you are using a Dell portable computer, 
press  . For other computers, see your 
documentation. 
 NOTE: Allow the projector some time...

www.dell.com | support.dell.com
24Troubleshooting Your Projector
Partial, scrolling, or 
incorrectly displayed image1Press the Resync button on the remote 
control or the control panel. 
2If you are using a Dell portable computer, set 
the resolution of the computer to XGA 
(1024 x 768): 
aRight-click the unused portion of your 
Windows desktop, click 
Properties and 
then select 
Settings tab.
bVerify the setting is  1024 x 768 pixels for 
the external monitor port.
cPress . 
If you experience...

Troubleshooting Your Projector25
Self-diagnostic for Video
Dell 1100MP Projector provides self-diagnost ic test of the projector video display 
(for Video, S-video, Component-i). Use thi s advanced feature for preliminary self-
diagnostic on your projector when en countering a display problem for video. 
1After turning on the projector, press the  and  buttons on the control panel 
simultaneously and release the bu ttons when screen goes blank. 
2Press the  and  buttons again to exit the diagnostic...

www.dell.com | support.dell.com
26Troubleshooting Your Projector
Changing the Lamp
Replace the lamp when the message  Lamp is approaching the 
end of its useful lif e. Replacement suggested! 
www.dell.com/lamps  appears on the screen. If this problem persists 
after replacing the lamp, contact Dell.
 
CAUTION: The lamp becomes very hot when  in use. Do not attempt to replace 
the lamp until the projector has bee n allowed to cool down for at least 
30 minutes. 
 
CAUTION: Do not touch the bulb  or the...

Specifications27
Specifications
5
Light Valve Single-chip DLP™ DDR 
(double data rate) technology
Brightness 1400 ANSI Lumens (Max) 
Contrast Ratio 2000:1 Typical (Full On/Full Off) 
Uniformity 80% Typical (Japan Standard - JBMA)
Lamp 200-watt user-replaceable UHP 2000- hour lamp(up to 2500 hours in 
eco mode)
Number of Pixels 800 x 600  (SVGA)
Displayable Color 16.7M colors
Color Wheel Speed 100~127.5Hz  (2X)
Projection Lens F/2.44~2.69, f=28.8~34.5mm with  1.2x manual zoom lens
Projection Screen Size...

www.dell.com | support.dell.com
28Specifications
Audio  1 speaker, 2 Watts RMS
Noise Level 34dB(A) Full-on mode, 
32dB(A) Eco-mode 
Weight 4.85 lbs (2.2 kgs)
Dimensions (W x H x D) External  9.9 x 3.96 x 8.4 ± 0.04 inches 
(251 x 101 x 213 ± 1mm)
Environmental Operating temperature: 0
oC–35oC 
(32oF–95oF)
Humidity: 80% maximum
Storage temperature: –20
oC to 60oC 
(–4oF to 140oF)
Humidity: 80% maximum
Regulatory FCC, CE, VCCI, UL, cUL, TüV- GS,  ICES-003, MIC, C-Tick, GOST, CCC, 
PSB, NOM,...

Specifications29
RS232 Pin Assignment
RS232 Protocol 
 Communication Settings 
 Control command Syntax (From PC to Projector) 
[H][AC][SoP][CRC][ID][SoM][COMMAND]
 Example: power on the projector  Enter the following code: 0xBE 0x EF 0x10 0x05 0x00 0xC7 0xBF 0x11 
0x11 0x01 0x00 0x02 
Connection settingsValue
Baud Rate: 19200
Data Bits: 8
Parity None
Stop Bits 1 

www.dell.com | support.dell.com
30Specifications
 Control Commands List 
Control 
Commands 
List  Address 
Code 
(BYTE)Size of the 
Pa y l o a d  
(WORD)CRC16 for 
the entire 
packet 
(WORD) MsG ID 
(WORD)
MsG size 
(WORD)Command 
code 
(BYTE) Command 
Description
0xefbe 0x10 0x0005 0xffc6 0x1111 0x0001 0x01 Power
0xbfc7 0x02 Menu
0x7e07 0x03 Up 0x3fc5 0x04 Down
0xfe05 0x05 Left
0xbe04 0x06 Right 0x7fc4 0x07 Resync
0x3fc0 0x08 Source
0xfe00 0x09 Volume+
0xbe01 0x0A Volume- 0xffc3 0x0D Mute
0xbfc2 0x0E...