Daewoo Dwd Fd1411 Instruction Manual

INSTRUCTION MANUAL
DWD-FD1411
Washing Machine Instruction Manual
CONTENTSPage
A NOTE TO YOU
Thank you for buying a DAEWOO appliance.
DAEWOO washing machines are easy to use, save time, and help you manage your home better.
This manual contains valuable information about how to operate and maintain your machine properly and safely.
Please read it carefully.
Economic wash system
Using artificial intelligence, the washer uses minimum energy and
water by selecting optimal water level and washing time.
Low...

2
PARTS AND FEATURES
The parts and features of your washer are illustrated on the page.
Become familiar with all parts and features before using your washer.
Accessories
NOTE
The drawings in the book may vary from your model model.
They are designed to show the different features of all models covered by this book,
therefore your model may not include all the features that are available.
Hose drain Inlet hose Manual Cap holder
ADJUSTABLE LEGS
CONTROL PANEL
DOOR
DETERGENT COMPARTMENT
INLET HOSE
PUMP...

3
Save these instructions
Your safety is important to us.
To reduce the risk of fire, electrical shock, or injury when using your machine adhere to the
following basic precautions.
Understanding your responsibilities
• Do not use chlorine bleach and ammonia or acid(such as vinegar or rust remover) in the same
wash. Hazardous fumes can form.
• Unplug power supply cord before attempting to service your machine.
• Do not wash fibreglass material.
Small particles can stick to fabrics washed in subsequent...

4
Removing transit bolts
1. Before operating the washer, remove the
transit bolts(3ea) along with the rubber.
• If the bolts are not removed, it may cause
heavy vibration, noise and malfunction.2. Unscrew the 3 bolts with the 10mm hex   
wrench or spanner or cross-tip screwdriver.
Keep the 3 bolts for a later time.
• When the appliance is transported, transit
bolts will be re-used.
3. Close the holes with the cap holders supplied.
Location of washer
• Check location where the machine will be installed....

5
The machine should be connected to the water mains using the the new hose sets supplied.
NEVER reuse old hoses.
If using only one water tap or if there is only one water inlet valve, connect the inlet hose to the
cold water inlet valve.
Caution: Be careful not to confuse hot water inlet and cold water inlet.
For Ordinary Tap
For Screw-Shaped Tap
INLET HOSE CONNECTION
1Pull down the collar of the
inlet hose to separate it
from the water tap
adapter.2Loosen the four screws
properly in order to fit into...

6
ELECTRICAL REQUIREMENTS
• An electrical earth is required on this machine
• If it does not fit the outlet, have a proper outlet
installed by a qualified electrician.• Don’t earth to a gas pipe.
• Don’t change the power supply cord plug.
• Check with a qualified electrician if you are not
sure the machine is properly earthed.
WARNING
Recommended earthing method Electrical shock hazard : Failure to follow these instructions could result in
death or serious injury.
For your personal safety, this machine...

7
OPERATING YOUR WASHING MACHINE
2Adjust the level of the washing machine using the adjustable legs.
• Please check if there is any gap between the
four adjustable legs and the floor.
• Turn the adjustable legs. adjust the level of the
machine and make sure that is stable.
• Adjust the fixing nuts tightly so that the washer
maintains the adjustment.
3Make it sure that the washing machine does not move when
you press down the four corners of the washers top plate.
adjustable legFixing Nut
NOTE
There...

8
• For best cleaning and wrinkle-free results, put clothes
into the machine loosely so that they move easily in
the water.
• Load machine properly and select correct load size
setting.
Overloading and selecting a setting too small for the
wash load can :
- Cause poor cleaning
- Increase wrinkling
- Create excessive lint
- Wear out items faster (because of damage to fibres)• Mix large and small items in each load. Load evenly to
maintain washer balance.
An unbalanced load can make the washer vibrate...

9
Press this switch to turn the power on or off.
Operation and temporary stop is repeated as it is pressed.
When you want to change program in operating;
press the “Start/Hold” button #Select the program that you want to change #press the
“Start/Hold” button again.
You can select the course you want, and each lamp is turned on when that course is selected.For the more detailed information, please refer to the page 11~18.
It can be used to adjust temperature of water according to types of the load to be...

10
1. COTTON IS AUTOMATICALLY SELECTED WHEN THE POWER BUTTON IS PRESSED.
• Press the Power button to start.
• Press the Start/Hold button
• Initial cycle:
- Programme : Cotton
- Wash : main wash
- Rinse : 3 times
- Spin : 800 rpm
- Water temperature : 40˚C
WASHING PROCEDURE AND PROGRAMME SELECTION
2. MANUAL SELECTION
• Press the Power button to start
• Select the cycle you want by turning the programme dial and pressing each button.
• Press the Start/Hold button.
3. TIME DELAYED WASHING
• A washing cycle...