D-Link Router DIR-600 User Manual

11
D-Link DIR-600 User Manual
Section 2 - Installation
If you are connecting the router to a cable/DSL/satellite modem, please follow the steps below:
1.  Place the router in an open and central location. Do not plug the power adapter into the router. 
2.  Turn  the  power  off  on  your  modem.  If  there  is  no  on/off  switch,  then  unplug  the  modem’s  power  adapter.  Shut  down 
your computer.
3.  Unplug  the  Ethernet  cable  (that  connects  your  computer  to  your  modem)  from  your...

12
D-Link DIR-600 User Manual
Section 2 - Installation
If  you  are  connecting  the  D-Link  router  to  another  router  to  use  as  a  wireless  access  point  and/or  switch,  you  will  have 
to do the following before connecting the router to your network:
• Disable UPnP
™
• Disable DHCP
•  Change  the  LAN  IP  address  to  an  available  address  on  your  network.  The  LAN  ports  on  the  router  cannot accept a DHCP address from your other router.
To connect to another router, please follow...

13
D-Link DIR-600 User Manual
Section 2 - Installation
6.  Disconnect the Ethernet cable from the router and reconnect your computer to your network. 
7.  Connect  an  Ethernet  cable  in  one  of  the  LAN  ports  of  the  router  and  connect  it  to  your  other  router.  Do  not  plug 
anything into the WAN port of the D-Link router. 
8.  You  may  now  use  the  other  three  LAN  ports  to  connect  other  Ethernet  devices  and  computers.  To  configure  your 
wireless  network,  open  a  web...

14
D-Link DIR-600 User Manual
Section 3 - Configuration
Configuration
This  section  will  show  you  how  to  configure  your  new  D-Link  wireless  router  using  the  web-based  configuration 
utility.
Web-based Configuration Utility
To  access  the  configuration  utility,  open  a  web-browser 
such  as  Internet  Explorer  and  enter  the  IP  address  of 
the router (192.168.0.1).
Enter  the  user  name  (admin)  and  your  password.  Leave 
the password blank by default.
If  you  get  a  Page...

15
D-Link DIR-600 User Manual
Section 3 - Configuration
Setup	 Wizard
You  may  run  the  setup  wizard  from  the  opening 
Internet  Setup  window  to  quickly  set  up  your  router. 
Click Internet  Connection  Setup	Wizard,  you  will 
be directed to the first window of the wizard.
Click Next to continue.
Create  a  new  password  and  then  click  Next  t o 
continue. 

16
D-Link DIR-600 User Manual
Section 3 - Configuration
Select  your  time  zone  and  NTP-ser ver  from  the  drop-down  menu 
and then click Next to continue.
Select  the  type  of  Internet  connection  you  use  and  then  click  Next 
to continue.
If  you  selected  Dynamic,  you  may  need  to  enter  the  MAC  address  of  the 
computer that was last connected directly to your modem. If you are currently 
using  that  computer,  click  Clone Your  PC’s  MAC  Address  and  then  click 
Next to...

17
D-Link DIR-600 User Manual
Section 3 - Configuration
If  you  selected  PPPoE,  enter  your  PPPoE  username  and  password.  Click 
Next to continue.
Select  Static  i f   yo u r   I S P   a s s i gn e d   yo u   t h e   I P   a d d re s s,   s u b n e t   m a s k , 
gateway, and DNS server addresses.
Note:  Make  sure  to  remove  your  PPPoE  software  from  your  computer.  The 
software is no longer needed and will not work through a router.
I f   yo u   s e l e c te d   P P T P,   e nte r   yo u...

18
D-Link DIR-600 User Manual
Section 3 - Configuration
If  you  selected  Static,  enter  your  network  settings  supplied  by  your  Internet 
provider. Click Next to continue.
Click Connect to save your settings.  
Please  allow  1-2  minutes  for  rebooting.  When  the  router  has  finished 
rebooting, the opening window will be displayed. 

19
D-Link DIR-600 User Manual
Section 3 - Configuration
Enter the IP address assigned by your ISP.
Enter the Subnet Mask assigned by your ISP.
Enter the Gateway assigned by your ISP.
Th e   d e f a u l t   MAC   Ad d re s s   i s   s e t   to   t h e   WA N’s   p hys i c a l 
interface  MAC  address  on  the  Broadband  Router.  It  is  not 
recommended  that  you  change  the  default  MAC  address 
unless required by your ISP.
Th e   d e f a u l t   MAC   a d d re s s   i s   s e t   to   t h e   WA...

20
D-Link DIR-600 User Manual
Section 3 - Configuration
The  Host  Name  is  optional  but  may  be  required  by  some 
ISPs.  The  default  host  name  is  the  device  name  of  the 
Router and may be changed.
Th e   d e f a u l t   MAC   Ad d re s s   i s   s e t   to   t h e   WA N’s   p hys i c a l 
interface  MAC  address  on  the  Broadband  Router.  It  is  not 
recommended  that  you  change  the  default  MAC  address 
unless required by your ISP.
Th e   d e f a u l t   MAC   a d d re s s   i...