Creative 2 Owners Manual
Have a look at the manual Creative 2 Owners Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 28 Creative manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
9:11 Embroidery mode - stitch-out C D 3. To line up the design on the screen with the previously embroidered, select matching point (C) to be the corner. Use the touch function - move or the corner icons. 4. Select the next function, rotate design (D) to move the matching point to the right position in the hoop. Use the touch function - rotate to line up the designs. Check that the needle is at the exact position. 5. Close precise positioning and start embroidering.
9:12Embroidery mode - stitch-out How to embroider with Inspira ™ Cutwork Needles 1. Hoop you fabric with heavy-weight water soluable stabilizer. 2. Look in your PFAFF ® creative sensation™ pro II Embroidery Collection and follow the instructions for your embroidery design. Start embroidering according to stitch-out order. 3. When your Embroidery Collection indicates it is time for the Cutwork Needle, remove the needle and top thread. 4. Each Inspira ™ Cutwork Needle has its own color. Match the color of the needle with the color of the needle shown in the Embroidery Collection. Replace the embroidery needle with the Inspira ™ Cutwork Needle. (illustration 1) 5. Complete all the needle blocks according to the Embroidery Collection. Two or four needles will be used depending on the embroidery design. 6. Thread your machine and add a heavy-weight water soluable stabilizer underneath the hoop. The next color block will baste the new stabilizer together with the hooped fabric. 7. Trim any remaining threads and remove the cut fabric. (Illustration 2) 8. Finish your embroidery. &OHDQWKHEREELQDUHDDIWHU
9:13 Embroidery mode - stitch-out 4 Common (PEURLGHU\VWLWFKRXW pop-ups (PEURLGHU\XQLWFDOLEUDWLRQ When the embroidery unit is attached, a pop-up asks you to slide off the hoop and clear the machine area for calibrating the embroidery arm. You will also be reminded to disengage the IDT ™ system and attach the Dynamic spring foot 6D for embroidery. Note: It is very important to remove the hoop, otherwise the hoop or the embroidery unit may be damaged while calibrating. Attach correct hoop If the size of the hoop attached to the machine does not match the size displayed on screen, the machine will not embroider. You must change the hoop to the displayed size or change the hoop setting to the hoop size attached. To change hoop settings, re-enter Embroidery edit and go to select hoop. %REELQWKUHDGORZPRYHWREREELQSRVLWLRQ When the bobbin thread is running low, a pop-up message appears giving you an indication that the bobbin needs to be changed soon. This gives you an opportunity to plan where to stop embroidering and change the bobbin. It is possible to embroider until the thread completely runs out. Press Start/Stop button to continue embroidering, without closing the bobbin thread low pop-up. Touch cancel to remain at the current stitch position. Touch OK to move the hoop to bobbin position. The hoop position tab opens. Replace the empty bobbin with a full one. Touch Current position and pull back excess needle thread. Move a few stitches backwards using the current stitch icons (4). Press start/stop or press your foot control to continue embroidering.
9:14Embroidery mode - stitch-out \QDPLFVSULQJIRRWLVUHFRPPHQGHG For regular embroidery it is always recommended to use the Dynamic spring foot 6D for best result. If you have deselected Dynamic spring foot 6D for embroidery in the Settings menu, the machine displays a pop-up when switching to Embroidery stitch-out, allowing you to select Dynamic spring foot 6D without opening the Settings menu. If foot 6A is selected, the ActivStitch ™ Technology feature will automatically select thread tension. Check needle thread The machine stops automatically if the needle thread runs out or breaks. Re-thread the needle thread, close the pop-up, step back a few stitches and start embroidering again. &KDQJHWKUHDGFRORU When it is time to change the needle thread, the machine stops and the upper thread is cut. Change the spool and re-thread the machine. The next recommended color is shown in the pop-up. Cut thread end If Cut jump stitches is not activated in Machine settings in the Settings menu, the machine will stop after stitching a few stitches. Cut the thread and press start/stop to continue embroidering. (PEURLGHU\LV
9:15 Embroidery mode - stitch-out &KDQJHWR&XWZRUN1HHGOH Some cutwork designs can be stitched out using the INSPIRA ™ Cutwork Needle. These designs are marked with a cutwork needle symbol in the creative sensation ™ pro II Embroidery Collection. When the machine stops and this pop-up message is shown, insert the corresponding cutwork needle. Touch OK and press the Start/Stop button to resume. Note: These cutwork designs can also be stitched out without the cutwork needles, but will then have to be cut manually. Machine needs to rest If the machine stops and this pop-up appears on the screen, the machine needs to rest. When the OK icon is enabled you can resume embroidery. The embroidery results will not be affected.
10:2Files & Folders 13 18 14 19 15 20 16 21 17 6 9 7 10 8 11 24 12 22 23 12345 Files & Folders - overview Parts of the selection bar 1. Stitches 2. Fonts 3. Designs 4. Files & Folders 5. Quick help Parts of Files & Folders /RDG
10:3 Files & Folders 1314151617 10 8 45 HVLJQÀOH (PEURLGHU\IRQWÀOH 6WLWFKÀOH 7H[WÀOH 6RXQGÀOH 8QUHFRJQL]HGÀOH File formats
10:4Files & Folders 1314151617 2 3HUVRQDOGHVLJQV 6WRUHGHVLJQÀOHVLQ3HUVRQDOGHVLJQV