compaq lte elite User Manual

NOTE: The first time you dock the computer in the convenience base, you
may be prompted to run Computer Setup to configure optional
devices. The computer automatically detects and configures many
optional devices. In some instances you will be prompted to
accept or reject a configuration change or to run Computer Setup.
Follow the instructions on the screen to change the system
configuration when required. Refer to Section 6.7 for more
information on running Computer Setup.
12. To turn off the computer...

following steps:
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION >>>>>>

5. Slide the computer toward you to remove it from the convenience base. 

Appendix E - Electrostatic Discharge 
 
Introduction 
This appendix covers the proper methods for grounding and the use of
recommended materials and equipment for preventing damage from
electrostatic discharge (ESD).
A sudden discharge of static electricity from a finger or other conductor
can destroy static-sensitive devices or micro circuitry. Often the spark is
neither felt nor heard, but damage occurs. An electronic device exposed to
electrostatic discharge may not be affected at all and will work...

o To avoid hand contact, transport products in static-safe containers such
as tubes, bags, or boxes.
o Protect all electrostatic parts and assemblies with conductive or
approved containers or packaging.
o Keep electrostatic sensitive parts in their containers until they arrive
at static-free stations.
o Place items on a grounded surface before removing them from their
container.
o Always be properly grounded when touching a sensitive component or
assembly.
o Place reusable electrostatic-sensitive parts...

Grounding Workstations
To prevent static damage at the workstation, use the following precautions:
o Cover the workstation with approved static-dissipative material. Provide
a wrist strap connected to the work surface and properly grounded tools
and equipment.
o Use static-dissipative mats, heel straps, or air ionizers to give added
protection.
o Handle electrostatic sensitive components, parts, and assemblies by the
case or PCB laminate. Handle them only at static-free workstations.
o Avoid contact with...

o Antistatic tape
o Antistatic smocks, aprons, or sleeve protectors
o Conductive bins and other assembly or soldering aids
o Conductive foam
o Conductive table-top workstations with ground cord of 1 megohm resistance
o Static dissipative table or floor mats with hard tie to ground
o Field service kits
o Static awareness labels
o Wrist straps and footwear straps providing 1 megohm +/-10% resistance
o Material handling packages
o Conductive plastic bags
o Conductive plastic tubes
o Conductive tote boxes
o...

Appendix F - Connecting and Configuring Optional  
SCSI-2 Devices 
 
Introduction 
This appendix contains guidelines for using SCSI-2 (small computer system
interface-2) devices, and explains how to connect external SCSI-2 devices,
install an internal SCSI-2 drive in the Compaq SmartStation, and install
SCSI-2 device drivers.
The expansion base has a built-in SCSI-2 controller, which allows you to
daisy-chain up to seven (one internal) SCSI-2 devices, such as hard drives,
CD-ROM drives, tape drives, WORM...

must install or remove according to your configuration.
4. External cables must be a minimum of 1 foot in length (0.3 meters). The
combined length of SCSI-2 cables in a chain must not be longer than
approximately 20 feet (6 meters).
5. Generally, each SCSI-2 device requires a software driver.
6. Most SCSI-2 drivers require that their associated device be turned on
during startup to recognize the device. Therefore, turn on external
SCSI-2 devices before turning on the expansion base.
F.2 Sample SCSI-2...

F.3 Changing The SCSI-2 Ddefault Configuration 
By default, the integrated SCSI-2 controller has the configuration settings
listed in Table F-1. To adjust the default settings, refer to the Compaq
EZ-SCSI Software Reference Guide.
Table F-1. SCSI Default Configuration
===========================================================================
Parameter Value
===========================================================================
SCSI ID 7
Parity Disabled
Disconnect Disabled (no disconnect)...