compaq evo notebook n1020v series User Manual

Removal and Replacement Procedures
Maintenance and Service Guide5–15
7. Spread the memory expansion slot retaining tabs 1 to release 
the memory expansion board. The board tilts up at a 
45-degree angle (Figure 5-11).
8. Remove the board by pulling it away from the connector at a 
45-degree angle 
2.
Figure 5-11. Removing a Memory Expansion Board
Reverse the preceding procedures to install a memory 
expansion board.
5.6 Mini PCI Communications Board
Mini PCI Communication Boards
Spare Part Number...

5–16Maintenance and Service Guide
Removal and Replacement Procedures
1. Prepare the computer for disassembly (Section 5.3).
2. Turn the computer bottom side up with the rear panel facing 
forward.
3. Remove the PM2.5 × 4.0 screw 
1 that secures the mini PCI 
compartment cover to the base enclosure (Figure 5-12).
4. Slide the cover to the left 
2.
5. Lift the left edge of the cover and swing it to the right 
3.
6. Remove the cover.
Figure 5-12. Removing the Mini PCI Communications 
Slot Cover
✎Mini PCI...

Removal and Replacement Procedures
Maintenance and Service Guide5–17
7. Disconnect the modem cable from the mini PCI 
communications board 
1 (Figure 5-13).
8. Spread the retaining tabs 
2 on each side of the mini PCI 
communications board. The board releases and rests at an 
angle.
9. Remove the board by pulling it away from the socket at an 
angle 
3.
Figure 5-13. Removing a Mini PCI Communications Board
Reverse the preceding procedures to install a mini PCI 
communications board. 

5–18Maintenance and Service Guide
Removal and Replacement Procedures
5.7 Disk Cell RTC Battery
1. Prepare the computer for disassembly (Section 5.3).
2. Remove the mini PCI compartment cover (Section 5.6).
3. Remove the RTC battery from its socket on the system board 
(Figure 5-14).
Figure 5-14. Removing the Disk Cell RTC Battery
✎The computer uses a CR1220 lithium disk cell battery. When 
replacing the RTC battery, insert the battery with the “+” sign 
facing up.
Disk Cell RTC Battery
Spare Part Number...

Removal and Replacement Procedures
Maintenance and Service Guide5–19
5.8 Connector Cover
✎The connector cover is available with carbon finish for Evo 
Notebook N1020v and N1000v models and silver finish for 
Presario 1500 models, and are included in the Miscellaneous 
Plastics/Hardware Kit, spare part number 285541-001.
1. Prepare the computer for disassembly (Section 5.3).
2. Turn the computer bottom side up with the rear panel facing 
forward.
3. Remove the two TM2.5 × 5.0 screws 
1 that secure the...

5–20Maintenance and Service Guide
Removal and Replacement Procedures
5.9 LED Cover
1. Prepare the computer for disassembly (Section 5.3).
2. Turn the computer bottom side up with the rear panel facing 
forward.
3. Remove the two TM2.5 × 8.0 screws that secure the LED 
cover to the base enclosure (Figure 5-16).
Figure 5-16. Removing the LED Cover Screws
LED Cover
Spare Part Number Information
LED cover
for use only with Evo Notebook N1020v models and Presario 
1500 models with config. codes beginning with...

Removal and Replacement Procedures
Maintenance and Service Guide5–21
4. Turn the computer top side up with the front facing forward.
5. Open the computer.
6. Press down and hold the 
F1 and F2 keys.
7. Insert a pointed tool into the notch in the LED cover 
1 
between the 
F1 and F2 keys and lift up (Figure 5-17).
8. Press down and hold the 
Pause and Scroll keys.
9. Insert a pointed tool into the notch in the LED cover 
2 
between the 
Pause and Scroll keys and lift up.
10. Remove the LED cover 
3....

5–22Maintenance and Service Guide
Removal and Replacement Procedures
5.10 Keyboard
Keyboards
Spare Part Number Information
For use only with TouchPad notebook models
Arabic
Belgian
Brazilian
Chinese
Czech
Danish
French
French Canadian
German
Hebrew
Hungarian
International
Italian
Japanese285530-171
285530-181
285530-201
285530-AA1
285530-221
285530-081
285530-051
285530-121
285530-041
285530-BB1
285530-211
285530-002
285530-061
285530-291Korean
Latin American Spanish
Norwegian
Portuguese
Russian...

Removal and Replacement Procedures
Maintenance and Service Guide5–23
1. Prepare the computer for disassembly (Section 5.3).
2. Remove the LED cover (Section 5.9).
3. Lift the back edge of the keyboard and swing it forward until 
it rests on the palm rest (Figure 5-18).
Figure 5-18. Releasing the Keyboard 

5–24Maintenance and Service Guide
Removal and Replacement Procedures
4. Release the ZIF connector 1 to which the keyboard cable is 
connected and disconnect the keyboard cable 
2 from the 
system board (Figure 5-19).
✎Dual Stick notebook models have an additional cable that must 
be disconnected. Release the ZIF connector 
3 to which the 
keyboard-to-TouchPad cable is attached and disconnect the 
cable4 from the keyboard.
Figure 5-19. Disconnecting the Keyboard-to-TouchPad Cable
5. Remove the keyboard....