compaq evo notebook n1000 series User Manual

Removal and Replacement Procedures
Maintenance and Service Guide5–39
6. Release the ZIF connector 1 to which the diskette drive cable 
is connected and disconnect the diskette drive cable 
2 from 
the drive (Figure 5-31).
7. Remove the diskette drive cable.
Figure 5-31. Removing the Diskette Drive Cable
Reverse the preceding procedures to install the diskette drive.
279372-001.book  Page 39  Friday, July 19, 2002  11:50 AM 

5–40Maintenance and Service Guide
Removal and Replacement Procedures
5.16 TouchPad Components
1. Prepare the computer for disassembly (Section 5.3).
2. Remove the palm rest (Section 5.14).
3. Remove the diskette drive (Section 5.15).
4. Turn the palm rest bottom side up with the speaker grilles 
facing away from you.
TouchPad Components
Spare Part Number Information
The TouchPad components for TouchPad notebook models consist of the 
TouchPad, TouchPad bracket, and TouchButton board. These components are...

Removal and Replacement Procedures
Maintenance and Service Guide5–41
5. Disconnect both ends of the TouchPad-to-TouchButton board 
cable 
1 from the low insertion force (LIF) connectors on the 
TouchPad 
2 and TouchButton board 3 (Figure 5-32).
6. Remove the TouchPad-to-TouchButton board cable.
Figure 5-32. Removing the TouchPad-to-TouchButton 
Board Cable
279372-001.book  Page 41  Friday, July 19, 2002  11:50 AM 

5–42Maintenance and Service Guide
Removal and Replacement Procedures
7. Remove the four TM2.5 × 5.0 screws 1 that secure the 
TouchPad, TouchButton board, and TouchPad bracket to the 
palm rest (Figure 5-33).
8. Remove the TouchPad bracket 
2, TouchButton board 3, and 
TouchPad 
4 from the palm rest.
Figure 5-33. Removing the TouchPad Components on 
TouchPad Models
279372-001.book  Page 42  Friday, July 19, 2002  11:50 AM 

Removal and Replacement Procedures
Maintenance and Service Guide5–43
✎Dual Stick notebook models have a different TouchPad 
configuration. An additional cable, screw, and board must be 
removed. Steps 9 through 13 apply to Dual Stick models only.
9. Release the ZIF connector 
1 on the pointing stick board to 
which the TouchButton board-to-pointing stick board cable is 
attached and disconnect the cable 
2 (Figure 5-34).
10. Release the ZIF connector 
3 on the TouchButton board to 
which the TouchButton...

5–44Maintenance and Service Guide
Removal and Replacement Procedures
12. Remove the five TM2.5 × 5.0 screws 1 that secure the 
TouchPad, TouchButton board, TouchPad bracket, and 
pointing stick board to the palm rest (Figure 5-35).
13. Remove the TouchPad bracket 
2, pointing stick board 3, 
To u c h P a d
4, and TouchButton board 5 from the palm rest..
Figure 5-35. Removing the TouchPad Components on Dual 
Stick Models
Reverse the preceding procedures to install the TouchPad 
components.
279372-001.book...

Removal and Replacement Procedures
Maintenance and Service Guide5–45
5.17 Display Release Assembly
✎The display release assembly is included in the Miscellaneous 
Plastics/Hardware Kit, spare part number 285541-001.
1. Prepare the computer for disassembly (Section 5.3).
2. Remove the palm rest (Section 5.14).
3. Turn the palm rest bottom side up with the speaker grilles 
facing forward.
4. Remove the two TM2.5 × 5.0 screws 
1 that secure the 
display release assembly to the palm rest (Figure 5-36).
5....

5–46Maintenance and Service Guide
Removal and Replacement Procedures
5.18 Charger Board
1. Prepare the computer for disassembly (Section 5.3).
2. Remove the palm rest (Section 5.14).
3. Remove the three TM2.5 × 5.0 screws 
1 that secure the 
charger board to the base enclosure (Figure 5-37).
4. Lift the front edge of the charger board shield 
2 until it clears 
the base enclosure, then slide the shield forward to remove it.
Charger Board
Spare Part Number Information
Charger board
The charger board...

Removal and Replacement Procedures
Maintenance and Service Guide5–47
5. Lift up on the back edge of the charger board 3 to disconnect 
it from the system board.
6. Remove the charger board 
4 from the base enclosure.
Figure 5-37. Removing the Charger Board
Reverse the preceding procedures to install the charger board.
5.19 Speaker Assembly
1. Prepare the computer for disassembly (Section 5.3).
2. Remove the palm rest (Section 5.14).
3. Remove the charger board (Section 5.18).
Speaker Assembly
Spare Part...

5–48Maintenance and Service Guide
Removal and Replacement Procedures
4. Disconnect the speaker cable 1 from the system board 
(Figure 5-38).
5. Swing the battery bay support bracket 
2 to the right until it 
clears the right edge of the speaker assembly.
6. Lift the front edge of the speaker assembly until it rests at an 
angle 
3.
7. Slide the speaker assembly forward and remove it 
4 from the 
base enclosure.
Figure 5-38. Removing the Speaker Assembly
Reverse the preceding procedures to install the...