compaq armada 110 User Manual

Removal and Replacement Procedures
Maintenance and Service Guide5–17
2. Remove the four M2.5 × 7 screws 1 and the M2.5 × 4.5 
screw 2 securing the heat sink to the base enclosure 
(Figure 5-10).
Figure 5–10: Removing the Heat Sink Screws 

5–18Maintenance and Service Guide
Removal and Replacement Procedures
3. Lift the front edge of the heat sink and swing it up and back 
until the shield rests at a 45-degree angle 1 (Figure 5-11).
4. Pull the heat sink away from the base enclosure at a 
45-degree angle 2 and remove it from the base enclosure.
Figure 5–11: Removing the Heat Sink
A thermal pad 3 is installed on the heat sink and makes contact 
with the processor. Any time the heat sink is removed, inspect the 
thermal pad for damage. 

Removal and Replacement Procedures
Maintenance and Service Guide5–19
Follow these steps to replace a damaged thermal pad:
a. Carefully peel the old thermal pad from the heat 
sink area.
b. Use a plastic straight edge tool (such as a credit card) to 
remove any thermal pad residue. Glue residue does not 
need to be totally removed. The glue used on the thermal 
pad has thermal conducting properties and will flow 
together with the glue from the new thermal pad.
Ä
CAUTION: Do not use any metal tools when...

5–20Maintenance and Service Guide
Removal and Replacement Procedures
5.10 Processor
1. Prepare the computer for disassembly (Section 5.3) and, in 
the order below, remove the following components:
❏LED cover (Section 5.5)
❏Keyboard (Section 5.6)
❏Optical drive (Section 5.7)
❏Heat sink (Section 5.9)
Processor
Spare Part Number Information
800 MHz Intel Pentium III
700 MHz Intel Celeron233551-001
233549-001 

Removal and Replacement Procedures
Maintenance and Service Guide5–21
2. Slide the processor lever to the left 1 and then swing it up 
and forward 2 until it is vertical (Figure 5-12).
3. Lift the outside edges of the processor straight up to remove it 
from the system board 3.
✎When replacing the processor, make sure the processor is seated 
in the processor socket with the gold triangle in the rear left 
corner 4.
✎If there is any thermal pad residue on the processor 5, use a 
plastic straight edge tool...

5–22Maintenance and Service Guide
Removal and Replacement Procedures
5.11 Top Cover
1. Prepare the computer for disassembly (Section 5.3) and, in 
the order below, remove the following components:
❏LED cover (Section 5.5)
❏Keyboard (Section 5.6)
❏Optical drive (Section 5.7)
❏Display (Section 5.8)
❏Heat sink (Section 5.9)
2. Turn the computer bottom side up with the front facing you.
✎The top cover is secured to the base enclosure by 15 screws that 
are two different sizes. Be sure to carefully note the...

Removal and Replacement Procedures
Maintenance and Service Guide5–23
3. Remove the 10 M2.5 × 7 screws 1 and the three M2.5 × 4.5 
screws 2 securing the top cover to the base enclosure 
(Figure 5-13).
Figure 5–13: Removing the Top Cover Screws 

5–24Maintenance and Service Guide
Removal and Replacement Procedures
4. Turn the computer top side up with the front facing you.
5. Disconnect the diskette drive cable from the low insertion 
force (LIF) connector on the system board 1 (Figure 5-14).
6. Disconnect the TouchPad cable from the LIF connector on 
the system board 2.
7. Remove the two M2.5 × 4.5 screws securing the top cover to 
the base enclosure 3.
8. Lift the top cover straight up to remove it from the base 
enclosure 4.
Figure 5–14:...

Removal and Replacement Procedures
Maintenance and Service Guide5–25
5.12 Diskette Drive
1. Prepare the computer for disassembly (Section 5.3) and, in 
the order below, remove the following components:
❏LED cover (Section 5.5)
❏Keyboard (Section 5.6)
❏Optical drive (Section 5.7)
❏Display (Section 5.8)
❏Heat sink (Section 5.9)
❏Top cover (Section 5.11)
2. Turn the top cover bottom side up with the front facing you.
Diskette Drive
Spare Part Number Information
Diskette drive 233553-001 

5–26Maintenance and Service Guide
Removal and Replacement Procedures
3. Remove the two M2.5 × 4.5 screws securing the diskette 
drive to the top cover 1 (Figure 5-15).
4. Remove the tape adhering the diskette drive and TouchPad 
cables to the top cover 2.
5. Remove the diskette drive from the top cover 3.
Figure 5–15: Removing the Diskette Drive
Reverse the above procedure to install the diskette drive.
✎When installing the diskette drive in the top cover, make sure the 
tab in the front right corner of...