Comdial Executech 32 Button Adjunct User Guide

							l Press specific telephone lineckey for line. 
-or- 
e Press 
1 m 4 on the telephone dial pad for line 
group. 
-or- 
e Press 0 on the telephone dial pad for no 
selection. (When 0 is stored and automatic 
dialing is used, system will pick line as- 
signed to telephone or last line used.) 
. Dial the number sequence to be stored from 
the telephone dial pad (up to 16 digits). 
l To store a pause, press HOLD on 
telephone. 
. To store a flash, press 
RECALL on 
telephone. 
To store another number for automatic 
dialing, 
l Press SAVE on telephone. 
. Press next Module key (or press 
HOLD plus 
Module key if DSS/BLF is programmed). 
l Select line, group or none as described 
above. 
e Dial number sequence as described above. 
. Repeat this procedure for each desired key. 
HINT: Store often-used, host system PBX or 
CENTREX feature access codes at Module key 
locations. This will provide one-key access to 
those host system features. 
To end programming, 
l Press MONITOR on telephone. 
To dial numbers automatically, 
0 Press desired Module key. 
-or- 
. If desired key is also programmed for 
DSS/BLF operation, 
e Press HOLD on telephone and then press 
desired key on Module. 
. When party answers, lift handset of 
telephone. 
OFF-HOOK VOICE ANNOUNCE 
AND HANDSFREE ANSWER- 
BACK 
The Adjunct Feature Module can receive a voice 
signalled intercom call (voice announce) at the 
same time that the paired station is active on 
another call. You can answer the voice sig- 
nalled intercom call in a handsfree manner 
without interrupting your currently active call. 
To answer voice announce in a 
COMDIAL 
Made rJ&t in the USA 
handsfree manner, 
. Hear voice signalling (voice announce) over Executech 
Module speaker, 
l Respond to voice announce by speaking 
toward Module (handsfree answerback). 32-Button Adjunct 
Feature Module 
Adjust the audio level of the voice signalling with 
the speaker volume control located on the right 
(With Voice Announce Capability) 
side of the Module. 
USER GUIDE 
For use with following hybrid/key system models: 
l 1432 Series 
0 22xx Series 
COMDWL 
Charlottesville, VA 22906 
GCA 70-096.01 
II June 1988 
~@w&i0~.  
						

							OVERVIEW 
The 32Button Adjunct Feature Module extends 
the memory keys of your Executech II multiline 
telephone by an additional thirty-two keys and 
status lights. The keys can be programmed for 
automatic dialing and/or direct station selection 
(DSS) with busy lamp field (BLF). 
This Module also provides an off-hook voice an- 
nounce and handsfree answerback features. 
With this capability, a second call can be an- 
nounced to you while you are engaged on a call. 
You can respond to the announcement, if neces- 
sary, in a handsfree manner. 
AuM DIAL & 
DSS KEYS 
7 
DIRECT STATION SELECTION 
BUSY LAMP FIELD (DSS/BLF) 
OPERATION 
DSS/BLF provides one-key intercom calling with 
visual indication of station status. 
To program DSS numbers, 
l Press ITCM on telephone. Listen for tone. 
l Dial 85 from telephone dial pad. Tone will 
stop. 
l Press desired key on Module. 
l Dial extension number from telephone dial 
pad. 
l Repeat previous two steps for all desired sta- 
tions. 
l Press MONITOR on telephone when 
programming is complete. 
. Record DSS names or locations on supplied 
reference card and install card on Module 
faceplate. 
l Lift out plastic reference card cover from 
Module faceplate. 
0 Write or type names in squares on 
reference card. 
0 Install card under cover and snap cover 
back into place on Module. 
NOTE: An autodial number also can be 
programmed as a secondary function at every 
DSSBLF memory location. See Automatic Dial- 
ing instructions for details. 
l%;$e announce a call to a DSS 
, 
l Lift telephone handset. 
l Press key on Module. 
l Voice announce. 
NOTE: If you are transferring a call, the outside 
line is automatically placed on hold when a DSS 
key is pressed. 
To tone signal a call to a DSS number, 
0 Lift telephone handset. 0 Press key on Module. 
. Press ITCM on telephone. When station 
answers, two-way conversation can take 
place. 
The BLF lights that are adjacent to the DSS 
keys on the Module indicate the status of the sta- 
tions programmed at the keys. Status condi- 
tions are as follows: 
BLF STATUS STATION STATUS 
Light Off 
Light Flashing Station Idle 
Station calling you on 
intercom line. 
Light On Steady Station busy. 
Station in do not dis- 
turb mode. 
Light Flutters Station has left call- 
back message. 
AUTOMATIC DIALING 
Auto dialing provides one-key calling of often 
used numbers and access codes. 
To store a number for automatic 
dialing, 
l Press ITCM on telephone. Listen for tone. 
l Press SAVE on telephone. Tone will stop. 
. Press desired key on Module. Listen for fast 
tone bursts. 
-or- 
. If desired key is also programmed for 
DSS/BLF operation (as described pre- 
viously), 
l Press HOLD on telephone and then press 
desired Module key. 
l Listen for fast tone bursts. 
l Select specific line, line group, or no selection 
as required.