Comdial Dxp Non-LCD Telephone Reference Manual

9.2 Storing Speed Dial Numbers
·
To store an outside number as a speed dial number, proceed
as follows:
NOTE: Programming overwrites existing speed dial numbers at button
locations.
1. PressINTERCOM.
2. DialSS1.
3. Press programmable button or dial pad button to choose
storage location (remember, to access second level storage at a
programmable button, pressSHIFTfirst).
4. Make your speed dial route selection choice from the
following list:
•press line button to select outside line,
•dial00to select...

9.3 Storing DSS Numbers
·
To store an intercom number as a DSS number,
NOTE: Storing DSS numbers at button locations will overwrite any
previously stored numbers.
1. PressINTERCOM.
2. DialSS3.
3. Press programmable button to choose DSS location.
4. Dial extension number.
5. Press next location button and store next DSS number.
6. Repeat the previous step until all DSS numbers are stored,
—OR—
pressSPEAKERto end.
Write Your DSS Numbers On This Chart
Programming Your Telephone GCA70–249
9 – 4 Non-LCD...

9.4 Storing The Feature Buttons
If you find that you are using certain features often, you can create
feature access buttons to make operations easier. Some features that you
may want to use frequently are defined as follows:
Account Code Button (ACCT)—allows you to enter an account code
for call record purposes.
Automatic Call-Back Button (CAMP)—arranges the system to ring
your telephone and another person’s telephone as soon as the other
telephone becomes idle.
Call Forward Button (CFWD)—allows you to...

You can store feature access codes at programmable buttons to provide
yourself with one-button access to features that you use quite often. To
find your feature codes of interest, turn to theQuick Reference Guide
located at the end of this publication.
·
To create these feature access buttons, proceed as follows:
1. PressINTERCOM.
2. DialSS3.
3. Press programmable button to choose storage location.
4. Dial the access code for the feature.
5. Press next location button and store next feature code.
6....

9.5 Storing The Response Message Button
You may program a RESPONSE MESSAGE button, which allows you
to send an LCD message to a caller who has initiated a SOHVA or
intercom call from another LCD telephone, or to send an LCD message
to another LCD telephone that you call and receive a busy signal or no
answer.
A fixed RESPONSE MESSAGE button sends the same preselected
message every time; you can program multiple fixed response message
buttons at your station. If, for example, you know that you want to...

This page remains blank intentionally. 

Operating Your Telephone
With A DSS/BLF Console
10.1 Operating Your Telephone
With A DSS/BLF Console
The IB24X, IB48X, and IB64X consoles have additional buttons and
status lights that extend the memory button capability of your telephone.
You can program the buttons for automatic dialing (speed dial) or direct
station selection (DSS) with busy lamp field (BLF) using instructions
provided in chapter 9,Programming Your Telephone.
When the installer assigns a DSS/BLF console to a station port, the
system...

10.1.1 Accessing The Button Levels
The IB24X and IB48X DSS/BLF consoles have four levels of buttons,
quadrupling the consoles’ button capacity. The four buttons at the bottom
of each console allow you to select which button level is currently active.
To change button levels, press one of the buttons at the bottom of the
console. The leftmost button activates level 1, the next button activates
level 2, etc. A light beside the appropriate button lights to indicate which
level is currently active.
ib48x...

Troubleshooting
Your Telephone
Symptom Possible Cause
INTERCOM light flashing. Your messaging is set. Press
INTERCOM,thendial#02and
hang up.
Station is ringing with ringer off.
HOLD light flashing with no line
on hold.Another telephone has activated
your message waiting light. Press
INTERCOMandthenpress
HOLDto retrieve message. This
action will call call party who
activated light. Once you have
received message, party who
activated light (while still talking
to you) must pressINTERCOM
to turn off the...

This page remains blank intentionally.