Comdial Dsu II Digital Telephone System Instructions Manual

2.18.5 Supporting The Tracker Paging System
The optional Tracker paging system allows you to send alpha/numeric or numeric-only messages
to the Tracker Pagers assigned to a station extension number. The type of message that the
system delivers is dependent on the Tracker Pager model being used. Tracker’s paging option
requires only one connection to the digital telephone system; however, you will need to take
several programming steps to make it operational.
·If you use station 10 programming to...

Power
On/Off
SwitchPower-In
JackON
OFF
POWERALARMEXTERNAL TRANSMITTER
TELEPHONE
EIA RS-232CANTENNA
Modular To EIA Adapter
With Male DB25 Connector
(Supplied In
Installation Kit) Kit-supplied
Line CordTo Serial Data Port
(COM1 for J0408,
COM4 for J0816 and J1632)
Tracker
Power
Supply
dsu262.cdr
TAB001–page6
IMI66–132 DSU II Digital Telephone System
2 – 80B Installing The DSU II Digital Telephone System 

3.4.15 Call Forward Outside System
Description:Call Forward Outside System (CFOS) gives station users the ability to forward line calls
to a location outside the DSU II Digital Telephone System. Be sure to set the abandon
hold release time on all lines that you use for CFOS to match the C.O. abandon hold
release time.
To Program:1. PressITCM,dialS#746S.“CONFIG MODE”
2. Dial17for system features.“SYSTEM FEATURES”
3. Dial14for system CFOS.“CFOS XXXXXXX”
4. PressA1key to toggle between enable and disabled...

Call Forward Outside System For Station Ports
Description:Use this procedure to enable or disable the CFOS (Call Forward Outside System) feature
for the station ports you select.
To Program:1. PressITCM,dialS#746S.“CONFIG. MODE”
2. Dial53for station features.“STATION FEATURES”
3. Dial42for station CFOS.“CFOS STATIONS”
4. Select station ports for programming to toggle status
Station 10–57 = Dial10–57
—OR—
Press DSS keysC10–C57on DSS console to enable or disable (LED On = Enable).
5. DialSfor station...

3.11.6 DCD Type Ring All Stations
Description:Enabling the system-wide ring all DCD feature causes a transferred call to ring at all idle
stations in a department until it is answered. The answering station gets the call while the
remaining stations retain their original status.
Default = disabled
To Program:1. PressITCM,dialS#746S.“CONFIG MODE”
2. Dial17for system features.“SYSTEM FEATURES”
3. Dial15for Ring All.“RING ALL XXX”
4. PressA1key to toggle between enable and disable (LED On = Enable)
—OR—...

3.17.7 SRA Alternate Line Groups
Description:The alternate line groups feature enables the system to try an alternate line group if no
lines are available in the original group. Each line group can have one alternate line
group. No alternate line groups are assigned by default. SRA alternate line groups are
included in database printouts.
If digit insertion is programmed, it will be done for the actual line group the call is being
routed over.
To Program:1. EnterIS746Sfor Main menu.
2. Enter1for system...

Station Monitoring
Visual Ring Indication Enable Disable
Audible Ring Indication Stations (10–57)
Default = Visual indication disabled, no audible indication assigned.
Tandem Attendant
Enable Disable
Default = Disable
Tone or Voice Signaling
Voice Tone
Default = Tone
SOHVA Tone Bursts123456
Default = 6
PA Options
Direct Ringing Lines
(1–24)
Delayed Ringing
Lines (1–24)
Night Ringing Lines
(1–24)
Zone Paging Enabled Zone 1 Zone 2 Zone 3 All-Call
Relay Port Relay
TrackingStation 17 Paging Port
PA Port...

4.4 Recording The Station Configurations
Use this sheet as an individual station record or as a record for a block of similarly programmed stations.
Make copies of this blank sheet as needed to meet system capacity.
Feature Choice Default Enter Station Port Numbers
Access Denied Lines 1–24 None
All-Call and Zone Paging Receive All/1–3 All
Originate All/1–3 All
Audible Monitoring None/Dir/Delay None
Automatic Hold Yes/No No
Automatic Hold - Intercom Yes/No No
Automatic Privacy
Privacy ReleaseNone/1–24...

Overflow Line Group
Default = None
Line Group Alternate Line Group
1
2
3
4
Default = None
SRA Wait Time 2 seconds 3 seconds 4 seconds
Default = 4 seconds
Line
GroupInsert Digits
12345678
1
2
3
4
Default = None
TAB001–page19
DSU II Digital Telephone System IMI66–132
Recording The System Settings 4 – 37 

4.7 Direct Department Calling Records
Enable/Disable DCD Type Ring All Stations
Enabled Disabled
Enable/Disable DCD Type Longest Idle Distribution
Enabled Disabled
Department 1
Access Code 10–7999
Line Ports 1–24
Station Ports 10–57
Department 2
Access Code 10–7999
Line Ports 1–24
Station Ports 10–57
Department 3
Access Code 10–7999
Line Ports 1–24
Station Ports 10–57
Department 3
Access Code 10–7999
Line Ports 1–24
Station Ports 10–57
Default = No access code assigned, no line ports assigned, and no...