Comdial Digitech Multiline Telephone Instructions Manual

							GCA70-280 DigiTeoh Station User’s Guide 
Making a Paging Announcement 
l To page through an external paging amplifier (if your 
system provides this feature), 
i . lit handset, 
2. press paging line select button and dial page access code (see your 
attendant for code) -- if paging is connected to a dedicated paging 
j:. 
port, dial ITCY 69, 
3. make announcement. 
l To page through system telephones (all- call and zone 
wing), 
1. lift handset, 
2. press ITCM and dial all-call or zone number: 
64,85, or 86 = zones 1.2, or 3 
67 = all-call, 
3. make announcement. 
4. hang up handset or waft for an answer. 
l To answer telephone paging from any station, 
1. lift handset, 
2. press ITCM, dial 66, and meet paging party on line. 
Switching Between Pulse and Tone 
l To convert to tone while dialing - If the local telephone 
service Is pulse (rotary) 
press # at point in dialing sequence where conversion to tone is 
required. 
NOTE: 
Pulse/Tone switching can be programmed into memory keys by pressing 
#during number storage. 
Forwarding Calls 
l To forward personal calls to another telephone, 
1. press ITCM and dial m 05, 
2. dial extension number of telephone to which calls are to be for- 
warded. 
l To cancel personal call forward, 
press ITCM and dial # 05. 
:  
						

							DigiTech Station User’s Guide GCA70-280 
l 
To forward all calls to another telephone, 
1. 
press ITCM and dial +K 5, 
2. dial extension number of station to which calls are to be forwarded. 
l 
To cancel allcall forward, 
press ITCM and dial t 5. 
NOTE: For each personal call received during call forward, you will hear a ring 
reminder (short tone burst) to remind you that calls are being forwarded. 
Using Automatic Call-Back 
l To arrange for the system to call back when a busy 
station becomes idle or rings with no answer, 
1. make intercom call and hear busy signal or ring-back tone, 
2. dial * 6, 
3. hang up. (When called station becomes idle or is operated by its 
user, your station will ring. Call-back is canceled if you do not lift your 
handset when you hear this tinging). 
l 
To answer call-back ring, 
lift handset (called station will ring; call-back is canceled if you do 
not lift your handset). 
l 
To cancel automatic call back, 
press ITCM and dial W 6, 
Using Call Waiting 
l To activate call waiting, 
1. make intercom call and hear busy signal, 
2. dial * 0 1 (called party hears tone), 
3. watt on line for an answer. 
l 
To cancel call waiting, 
hang up handset. 
l 
To answer a call-waiting tone at your telephone, 
1. hear short tone burst in handset receiver, 
2. complete present call, and hang up (waiting call will begin ringing), :. 
:, 
3. lift handset to answer. .  
						

							Engaging Automatic Set Relocation 
NOTE: If this feature has been enabled by your system programmer, the mes- 
sage-waiting light will flash for several seconds when you corinect your 
telephone to another location. This means that the system Is waiting to 
automatically relocate your extension number and other programmed 
features to the new location. 
If you do not want your telephone to have all of fts old programming after 
relocation, reject the automatic relocation. 
l To accept automatic relocation, 
do nothing and wait for the light to turn off on its own, or press the 
HOLD button to immediately accept the relocation (light immediately 
turns off). 
l To reject the automatic relocation, 
press the I button while the message waiting light is flashing. 
Programming Your Telephone 
l 
To store autodial numbers, 
1. presslTCManddial**l, 
2. press programmable button, 
3. press line button, or dial 1,2,3, or 4, to select line groups 1 - 4, or 
dial 0 for system to select line, 
4. dial number to be stored (16 digits max.) 
l to store hookflash in an autodial sequence, press TAP; press 
HOLD to store pause (only if needed), 
5. press TRANSICONF, then press next programmable button, and 
dial another number to be stored, 
6. repeat previous step until finished then press SPKR. 
NOTEr You can store an autodial number at a second level at a 
DSS button if you wish. 
l To store extension numbers at DSS buttons, 
1. press ITCM and dial +k * 3, 
2. press programmable button, 
3. dial extension number, 
4. press next programmable button and dial another extension num- 
ber, 
5. repeat previous step until finished then press SPKR. 
13  
						

							DigiTech Station User’s Guide GCA78280 
l 
To store personal speed dial numbers, 
1. press ITCM and dial * 4 2, 
2. dial memory location (l-0). 
3. press line button, or dial 1,2,3, or 4 to select line groups i- 4, 
or dial 0 for system to select line, 
4. dial number to be stored (16 digits max.) press TAP to store 
hookfiash and press HOLD to store pause (if needed), 
5. press TRANYCONF, dial next location, select line, and dial another 
number to be stored, 
6. repeat previous step until finished, then press SPKR. 
l 
To store special purpose feature buttons, 
1. press ITCM and dial Y * 1, 
2. press programmable button, 
3. dial feature code: 
5 = response messaging button (then dial O-9 for message) 
6 = transfer to voice mail button (then dial extension number) 
7 = assist button (than dlal O-9 or l for message) 
8 subdued off-hook voice announce button 
96 = group listen button 
# = auto redial button 
4. press TRANYCONF then next programmable button and dial an- 
other feature code, 
5. repeat step 5 untfl finished, then press SPKR. 
*. 
L. 
;,:. 
.:  
						

							GCA7Cb280 ulgl 1 ecn sitatlon users tiu~aa 
1 
Index 
Answering Calls.. ................................... 5 
Answering SOHVA.. 5, 6 / 
.............................. 
Automatic Call Back .............................. 12 
Automatic Set Relocation.. 
.................... 13 
Call Waittng.. 
......................................... 12 
Conferencing.. ....................................... 9 
DigiTech Telephone , ............................. 2 
FlashiRecall........................................... 10 
Forwarding Calls.. .................................. 11, 12 
Holding Calls.. 
........................................ 7, 6 
Introduction.. .......................................... 2 
Lights, Telephone.. 
................................ 3, 4 
Making a Call.. ....................................... 6, 7 
Messaging.. ........................................... 10 
Paging.. .................................................. 10, 11 
Programming your Telephone.. .............. 13, 14 
Pulse/Tone Telephones.. 
....................... 11 
RecalVflash ........................................... 10 
SOHVA Calls.. 
....................................... 5, 6 
Speakerphone, Using the.. .................... 5 
Telephone Lights ................................... 
394 
Transferring Calls .................................. 9 
15  
						

							This manual has been developed by Com- 
dial Corporation (the ‘Company’) and is 
intended for the use of its customers and 
service personnel. The information in this 
manual is subject to change without notice. 
While every effort has been made to elimi- 
nate errors, the Company disclaims liability 
for any difftculties arising from the interpre- 
tation of the information contained herein. 
The information contained herein does not 
purport to cover all details or variations in 
equipment or to provfde for every possible 
contingency to be met in connection with 
installation, operation, or maintenance. 
Should further information be desired, or 
should particular problems arise which are 
not covered sufficiently for the purchaser’s 
purposes contact, Comdial, Inside Sales 
Department, P.O. Box 7266, Chartottes- 
ville, Virginia 22906. 
COMDIAL Charlottesville, VA 22906-7266 
I- 
Jrt&-*‘b 
Printed In U.S.A. GCA 70-280.01 
6m