Comdial Digitech 32 Button Dss Blf Console User Guide

							l Press desired storage location button on 
Console. Listen for fast tone bursts. 
0 Select specific line, line group, or no selec- 
tion as required. 
l Press specific telephone line button for 
line. 
-or- 
0 Press 1 - 4 on the telephone dial pad for 
line group. 
-or- 
. Press 0 on the telephone dial cad for no 
selection. (When 0 is stored and automatic 
dialing is used, system will pick line as- 
signed to telephone or last line used.) 
l Dial the number sequence to be stored from 
the telephone dial pad (up to 16 digits). 
l To store a pause, press HOLD on 
telephone. 
l To store a flash, press TAP on telephone. 
To store another number for automatic dial- 
W, 
l Press TRANSICONF on telephone. 
l Press next Console button. 
o Select line, group or none as described 
above. 
0 Dial number sequence as described above. 
. Repeat procedure for each desired button. 
HINT: Store often-used, host system PBX or 
CENTREX feature access codes at Console but- 
ton locations. This willprovide one-button access 
to those host system features. 
To end programming, 
. Press MNTR (SPKR) on telephone. 
DIALING NUMBERS 
To dial numbers automatically, 
. Press desired Console button. 
-or- 
0 If desired button also provides DSS/BLF 
operation, 
l Press HOLD on telephone and then press 
desired button on Console. 
l When party answers, lift handset of 
telephone. 
I 
FREQUENTLY 
CALLED NUMBERS 
COMDIAL 
Charlottesville, VA 22906-7266 
Printed in U.S.A. GCA70-187.02 
-m 4’g1 
DIGITECH 
32-Button DSS/BLF 
Console 
User’s Guide 
DigiTech system models:  
						

							OVERVIEW DSS/BLF OPERATION 
The 32-Button DSS/BLF Console extends the 
memory button capability of an adjacent com- 
panion DigiTech telephone by an additional 32 
buttons and status lights. The buttons can be 
programmed for automatic dialing (autodial) 
and/or direct station selection (DSS) with busy 
lamp field (BLF). 
OS BUTTONS - 
BLF 
STATUS 
LIGHTS h 
REFERENCE 1 
CARD 1 
/ - 
- ass BUT-I 
‘ON 
L OS BUTTON FOR FOR STATION 
STATION PORT 10 PORT 41 
When a DSSiBLF console is initially connected at 
a station port, the system recognizes it as such, 
and automatically assigns the station intercom 
numbers to the console buttons for the maximum 
numberof stations connected to the system. (The 
maximum coverage is limited by the 32 available 
buttons.) DSS/BLF provides one-button intercom calling 
with visual indication of station status. 
STORING DSS NUMBERS 
To program DSS numbers, 
Press ITCM on telephone. Listen for tone. 
Dial +@ t 3 from telephone dial pad. Tone 
will stop. 
Press desired button on Console. 
Dial extension number from telephone dial 
pad. 
Repeat previous two steps for all desired 
stations. 
Press MNTR (SPKR) on telephone when 
programming is complete. 
Record DSS names or locations on supplied 
reference card and install card on Console 
faceplate. 
. Lii out plastic reference card cover from 
Console faceplate. 
l Write or type names in squares on refer- 
ence card. 
l Install card under cover and snap cover 
back into place on Console. 
To blank a DSS button, 
l Press ITCM on telephone 
l Dial t t 3 from telephone dial pad. 
l Press desired console button. 
l Press MNTR (SPKR) on telephone. 
DSS CALLING 
To voice announce a call to a DSS number, 
l Lift telephone handset. 
l Press DSS button on Console. 
l Voice announce. 
NOTE: If you are transferring an outside call to an 
intercom station, press the TRANS/CONF button 
on the telephone before pressing the DSS button 
on your Console. 
To tone signal a call to a DSS number, 
l Lift telephone handset. . 
. 
The Press DSS button on Console. 
Press ITCM on telephone. When station 
answers, two-way conversation can take 
place. 
BLF lights that are adjacent to the DSS 
buttons on the Console indicate the status of the 
stations programmed at the buttons. Status con- 
ditions are as follows: 
BLF STATUS STATION STATUS 
Light Off Station Idle. 
Light Flashing Station calling you on 
intercom line. 
Station ringing if 
monitoring feature is 
I 
active. 
I Light On Steady 
I 
1 Station busy. 
I. 1 I 
Station in do not dis- 
turb mode. 
Light Flutters Station has left call- 
back message. 
NOTE: An autodial number also can be 
programmed as a secondary function at every 
DSSIBLF memory location. See Automatic Dial- 
ing instructions for details. 
AUTOMATIC DIALING 
Automatic dialing provides one- or two-button 
calling of often used numbers and access codes 
as a secondary function of the DSS buttons. For 
a primary autodial function, blank the DSS/BLF 
function at the desired buttons. 
STORING NUMBERS 
To store a number for automatic dialing, 
l Press ITCM on telephone. Listen for tone. 
l Dial t t 1 from the telephone dial pad. Tone 
will stop. 
GCA 70-l 87