Cisco Wsc2960c8pcl Manual

 
11
Catalyst 3560-C and 2960-C Switch Getting Started Guide
OL-23802-02
Catalyst 3560-C and 2960-C  Switch Getting Started Guide
Switch RJ-45 Console Port
1.Connect the RJ-45-to-DB-9 adapter cable to the 9-pin serial port on the PC. 
Connect the other end of the cable to the console port on the switch.
2.Start a terminal-emulation program on the PC.
3.Configure the PC terminal emulation software for 9600 baud, 8 data bits, no 
parity, 1 stop bit, and no flow control.
4.Use the CLI to enter commands to...

 
Catalyst 3560-C and 2960-C Switch Getting Started Guide
  
12
Catalyst 3560-C and 2960-C Sw itch Getting Started Guide
OL-23802-02
See the “Accessing Help Online” section on page  22  for a list of supporting 
documentation.
Installing the Switch
This section covers desk-mounting procedures. As examples, all the illustrations 
show the Catalyst  2960CPD-8PT-L switch. For alternate mounting procedures, 
such 

as installing the switch in a rack , under the desk, on a wall, or for using a 
mounting tray...

 
13
Catalyst 3560-C and 2960-C Switch Getting Started Guide
OL-23802-02
Catalyst 3560-C and 2960-C  Switch Getting Started Guide
 Airflow around the switch and through the vents must be unrestricted. We 
strongly recommend that you allow at least 3  in. (7.6 cm) of clearance from 
t

he left, right, and top sides of the switch to avoid any flow blockage. If you 
are installing the switch in a rack, allow at least 1.75  in. (4 cm) of empty rack 
space a

bove each switch.
When placing the switch on a...

 
Catalyst 3560-C and 2960-C Switch Getting Started Guide
  
14
Catalyst 3560-C and 2960-C Sw itch Getting Started Guide
OL-23802-02
WarningThis equipment must be grounded. Never defeat the ground conductor or 
operate the equipment in the absence of a suitably installed ground conductor. 
Contact the appropriate electrical inspection authority or an electrician if you 
are uncertain that suitable grounding is available. Statement 1024
WarningTo prevent the system from overheating, do not operate it in...

 
15
Catalyst 3560-C and 2960-C Switch Getting Started Guide
OL-23802-02
Catalyst 3560-C and 2960-C  Switch Getting Started Guide
NoteFor instructions on mounting the switch under a desk or on a wall, see the 
hardware installation guide on Cisco.com.
To secure the switch on top of or under a desk or a shelf, use the mounting 
template and three mounting screws.
1.Position the mounting template on the mounting surface with the two 
side-by-side slots forward.  Peel the adhesive strip off the bottom, and...

 
Catalyst 3560-C and 2960-C Switch Getting Started Guide
  
16
Catalyst 3560-C and 2960-C Sw itch Getting Started Guide
OL-23802-02
4.Place the switch onto the mounting screws, and slide it forward until it locks 
in place.
1
Slides on this way 3Desk or shelf
2 Screws
208781
3
2
1
CONSOLE1 2
 
Se riesPDP OW ERO VERE TH ER N ET
12 3456 78PD
SPDPoEDPL
X
S
TAT
S
Y ST 

 
17
Catalyst 3560-C and 2960-C Switch Getting Started Guide
OL-23802-02
Catalyst 3560-C and 2960-C  Switch Getting Started Guide
Connecting to the Switch Ports
Connect to the 10/100 and 10/100/1000 Ports
The fixed ports on some Catalyst 3560-C and 2960-C models support Power over 
Ethernet (PoE) and PoE+. See the switch  software configuration guide for more 
information. Some models also support PoE pass-through. For information on the 
PoE pass-through feature, see  the switch hardware guide. 
NoteThe...

 
Catalyst 3560-C and 2960-C Switch Getting Started Guide
  
18
Catalyst 3560-C and 2960-C Sw itch Getting Started Guide
OL-23802-02
Install the SFP Modules 
Some Catalyst 3560-C and 2960-C models have SFP module slots. 
For a list of supported modules, see the release notes on Cisco.com. For detailed 
i
 nstructions on installing, removing, and connecting to SFP modules, see the 
documentation that came with the SFP module.
CautionRemoving and installing an SFP module can  shorten its useful life. Do...

 
19
Catalyst 3560-C and 2960-C Switch Getting Started Guide
OL-23802-02
Catalyst 3560-C and 2960-C  Switch Getting Started Guide
Connecting to PoE Devices
You can connect the switch to IP device s such as IP phones and access points. 
Some switch models can power the IP device, depending upon the surplus power 
they have. See the switch hardware guide for information.
Verify Port Connectivity
After you connect the switch port and another device, the port LED turns amber 
while the switch establishes a...

 
Catalyst 3560-C and 2960-C Switch Getting Started Guide
  
20
Catalyst 3560-C and 2960-C Sw itch Getting Started Guide
OL-23802-02
Troubleshooting Express Setup
If Express Setup does not run, or if the Express Setup page does not appear in your 
browser:
Did you verify that POST ran 
suc
 cessfully before starting 
Express Setup? If not, make sure that only the SYST and 
ST
AT LEDs are green before you press the 
Mode button to enter the Express Setup 
mode.
POST errors are usually fatal. Contact your...