Cisco Router 800 Series Software Configuration Guide

 
7-81
Cisco 800 Series Software Configuration Guide
78-5372-06
Chapter 7      Router Feature Configuration
Cisco 827 Router Configuration Examples
session target ipv4:1.0.0.2
!
Cisco 827 Router Configuration 
The following is a configuration for the Cisco 827 router. You do not need to 
enter the commands marked “default.” These commands appear automatically in 
the configuration file that is generated when you use the show running-config 
command.
Current configuration:
!
version 12.0
no service pad...

 
Chapter 7      Router Feature Configuration
Cisco 827 Router Configuration Examples
7-82
Cisco 800 Series Software Configuration Guide
78-5372-06 ip classless (default)
!
line con 0
exec-timeout 10 0
password 4youreyesonly
login
transport input none (default)
stopbits 1 (default)
line vty 0 4
password secret
login
!
end
Corporate or Endpoint Router Configuration for Data Network
This section shows a configuration that you can use to configure a Cisco 3600 
router as a corporate or endpoint router in...

 
7-83
Cisco 800 Series Software Configuration Guide
78-5372-06
Chapter 7      Router Feature Configuration
Cisco 827 Router Configuration Examples
network 30.0.0.0
no auto-summary
!
no ip http server (default)
ip classless (default)
!
protocol ip 2.0.0.1 broadcast
!
line con 0
 exec-timeout 0 0
 transport input none (default)
 stopbits 1 (default)
line vty 0 4
password secret
login
!
end
Corporate or Endpoint Router Configuration for Data and Voice 
Network
This section shows a configuration that you...

 
Chapter 7      Router Feature Configuration
Cisco 827 Router Configuration Examples
7-84
Cisco 800 Series Software Configuration Guide
78-5372-06 !
voice-port 1/1/0
!
voice-port 1/1/1
!
dial-peer voice 101 pots
 destination-pattern 5552222
 port 1/0/0
!
dial-peer voice 102 pots
 destination-pattern 5554444
 port 1/0/1
!
dial-peer voice 103 pots
 destination-pattern 5556666
 port 1/1/0
!
dial-peer voice 104 pots
 destination-pattern 5558888
 port 1/1/1
dial-peer voice 1100 voip
 destination-pattern...

 
7-85
Cisco 800 Series Software Configuration Guide
78-5372-06
Chapter 7      Router Feature Configuration
Cisco 827 Router Configuration Examples
interface Ethernet0/1
 no ip address
 no ip directed-broadcast (default)
shutdown
!
router rip
version 2
network 3.0.0.0
!
ip classless (default)
ip route 0.0.0.0 0.0.0.0 Ethernet 0/0
ip route 1.0.0.0 255.0.0.0 3.0.0.0
ip route 2.0.0.0 255.0.0.0 3.0.0.1
ip route 5.0.0.0 255.0.0.0 3.0.0.1
ip route 40.0.0.0 255.255.255.0 172.28.9.1
ip route 172.28.5.0...

 
Chapter 7      Router Feature Configuration
Cisco 827 Router Configuration Examples
7-86
Cisco 800 Series Software Configuration Guide
78-5372-06 

CHAPTER
 
8-1
Cisco 800 Series Software Configuration Guide
78-5372-06
8
Advanced Router Configuration
This chapter includes advanced configuration procedures for the Cisco 800 series 
and Cisco SOHO series routers.
NoteEvery feature described is not necessarily supported on every router model. 
Where possible and applicable, these feature limitations will be listed.
If you prefer to use network scenarios to build a network, see Chapter 4, 
“Network Scenarios.” For basic router configuration topics, see...

 
Chapter 8      Advanced Router Configuration
Configuring Support for PPP over Ethernet
8-2
Cisco 800 Series Software Configuration Guide
78-5372-06
Configuring IP Named Access Lists, page 8-29
Configuring International Phone Support, page 8-29
Configuring Committed Access Rate, page 8-36
Configuring VPN IPSec Support Through NAT, page 8-37
NAT Default Inside Server Enhancement, page 8-38
Configuring VoAAL2 ATM Forum Profile 9 Support, page 8-40
Configuring ATM OAM F5 Continuity Check Support,...

 
8-3
Cisco 800 Series Software Configuration Guide
78-5372-06
Chapter 8      Advanced Router Configuration
Configuring Support for PPP over Ethernet
Configuring PPPoE Client Support
PPPoE is supported on the following Cisco routers:
Cisco 806 and 831
Cisco 826 and 836
Cisco 827, 827H, 827-4V, and 837
Cisco SOHO 77, SOHO 77H, SOHO 78, SOHO 96, and SOHO 97
Cisco 828 
The PPPoE client is supported on an ATM permanent virtual circuit (PVC). Only 
one PPPoE client is supported on a single ATM PVC....

 
Chapter 8      Advanced Router Configuration
Configuring Support for PPP over Ethernet
8-4
Cisco 800 Series Software Configuration Guide
78-5372-06
d.Configure the dialer-group number by entering the dialer-group number 
command.
e.Configure a dialer list corresponding to the dialer-group by entering the 
dialer-list 1 protocol ip permit command.
NoteMultiple PPPoE clients can run on a different PVCs, in which case each client 
has to use a separate dialer interface and a separate dialer pool, and the...