Cisco Router 800 Series Software Configuration Guide
Here you can view all the pages of manual Cisco Router 800 Series Software Configuration Guide. The Cisco manuals for Router are available online for free. You can easily download all the documents as PDF.
Page 261
6-25 Cisco 800 Series Software Configuration Guide 78-5372-06 Chapter 6 Configuring Telephone Interfaces POTS Dial Feature (Japan Only) Events Ta b l e 6 - 6 shows the values for events that are translated into CSM events. Table 6-6 Event Values and Corresponding CSM Events Hexadecimal Value Event CSM Event 0x0 DEV_IDLE CSM_EVENT_ISDN_DISCONNECTED 0x1 DEV_INCALL CSM_EVENT_ISDN_CALL 0x2 DEV_SETUP_ACK CSM_EVENT_ISDN_SETUP_ACK 0x3 DEV_CALL_PROC CSM_EVENT_ISDN_PROC 0x4 DEV_CONNECTED...
Page 262
Chapter 6 Configuring Telephone Interfaces POTS Dial Feature (Japan Only) 6-26 Cisco 800 Series Software Configuration Guide 78-5372-06 Cause Values Ta b l e 6 - 7 shows cause values that are assigned only to call-progressing events. Table 6-7 Cause Values and Definitions Hexadecimal Value Cause Definitions 0x01 UNASSIGNED_NUMBER 0x02 NO_ROUTE 0x03 NO_ROUTE_DEST 0x04 NO_PREFIX 0x06 CHANNEL_UNACCEPTABLE 0x07 CALL_AWARDED 0x08 CALL_PROC_OR_ERROR 0x09 PREFIX_DIALED_ERROR 0x0a PREFIX_NOT_DIALED 0x0b...
Page 263
6-27 Cisco 800 Series Software Configuration Guide 78-5372-06 Chapter 6 Configuring Telephone Interfaces POTS Dial Feature (Japan Only) 0x22 NO_CIRCUIT_AVAILABLE 0x26 NETWORK_OUT_OF_ORDER 0x29 TEMPORARY_FAILURE 0x2a NETWORK_CONGESTION 0x2b ACCESS_INFO_DISCARDED 0x2c REQ_CHANNEL_NOT_AVAIL 0x2d PRE_EMPTED 0x2f RESOURCES_UNAVAILABLE 0x32 FACILITY_NOT_SUBSCRIBED 0x33 BEARER_CAP_INCOMPAT 0x34 OUTGOING_CALL_BARRED 0x36 INCOMING_CALL_BARRED 0x39 BEARER_CAP_NOT_AUTH 0x3a BEAR_CAP_NOT_AVAIL 0x3b...
Page 264
Chapter 6 Configuring Telephone Interfaces POTS Dial Feature (Japan Only) 6-28 Cisco 800 Series Software Configuration Guide 78-5372-06 Call Scenarios for the POTS Dial Feature This section describes three call scenarios and shows examples of the Cisco IOS command output for each scenario. The output examples for the debug and disconnect commands show the sequence of events that occur during a POTS dial call.0x54 NO_CALL_SUSPENDED 0x55 CALL_ID_IN_USE 0x56 CALL_ID_CLEARED 0x58 INCOMPATIBLE_DEST...
Page 265
6-29 Cisco 800 Series Software Configuration Guide 78-5372-06 Chapter 6 Configuring Telephone Interfaces POTS Dial Feature (Japan Only) Call Scenario 1 In this call scenario, port 1 is on-hook, the application dial is set to call 4085552221, and the far end successfully connects. The following example shows the Cisco IOS command: router# test pots 1 dial 4085552221# router# The following screen output shows an event indicating that port 1 is being used by the dial application: 01:0, port = 1...
Page 266
Chapter 6 Configuring Telephone Interfaces POTS Dial Feature (Japan Only) 6-30 Cisco 800 Series Software Configuration Guide 78-5372-06 The following screen output shows a call-connecting event pair indicating that the telephone at the far end has answered: 01:58:48: EVENT_FROM_ISDN:dchan_idb=0x280AF38, call_id=0x8004, ces=0x1 bchan=0xFFFFFFFF, event=0x4, cause=0x0 01:58:48: CSM_PROC_CONNECTING: CSM_EVENT_ISDN_CONNECTED, call id = 0x8004, port = 1 The following screen output shows a...
Page 267
6-31 Cisco 800 Series Software Configuration Guide 78-5372-06 Chapter 6 Configuring Telephone Interfaces POTS Dial Feature (Japan Only) 01:59:42: CSM_PROC_APPLIC_DIALING: CSM_EVENT_VDEV_DIGIT, call id = 0x0, port = 1 01:59:42: CSM_PROC_APPLIC_DIALING: CSM_EVENT_VDEV_DIGIT, call id = 0x0, port = 1 01:59:42: CSM_PROC_APPLIC_DIALING: CSM_EVENT_VDEV_DIGIT, call id = 0x0, port = 1 01:59:42: CSM_PROC_APPLIC_DIALING: CSM_EVENT_VDEV_DIGIT, call id = 0x0, port = 1 01:59:42: CSM_PROC_APPLIC_DIALING:...
Page 268
Chapter 6 Configuring Telephone Interfaces POTS Dial Feature (Japan Only) 6-32 Cisco 800 Series Software Configuration Guide 78-5372-06 Call Scenario 3 In this call scenario, port 1 is on-hook, the application dial is set to call 4086661112, the far end successfully connects, and the command test pots disconnect terminates the call. router# debug pots csm router# test pots 1 dial 4086661112 router# The following screen output follows the same sequence of events as shown in Call Scenario 1:...
Page 269
6-33 Cisco 800 Series Software Configuration Guide 78-5372-06 Chapter 6 Configuring Telephone Interfaces Cisco 813 Router Enhanced Voice Features (Japan Only) 1d03h: CSM_PROC_DISCONNECTING: CSM_EVENT_ISDN_DISCONNECTED, call id = 0x8039, port = 1 1d03h: CSM_PROC_DISCONNECTING: CSM_EVENT_TIMEOUT, call id = 0x8039, port = 1 Cisco 813 Router Enhanced Voice Features (Japan Only) The Cisco 813 router supports the enhanced voice features in addition to the standard voice features of the Ciso 800 series...
Page 270
Chapter 6 Configuring Telephone Interfaces Cisco 813 Router Enhanced Voice Features (Japan Only) 6-34 Cisco 800 Series Software Configuration Guide 78-5372-06 General Requirements and Restrictions The following is a list of requirements for activating the enhanced voice features on the Cisco 813 router: Subscription to the NTT INS-NET-64 switch type. Configuration of the router telephone ports to the Japanese standards by using the Cisco IOS command pots country jp. Caller ID Display This...