Cisco Rfgw1d Manual

 
  Important Safety Instructions  
78-4025112-01 Rev H0 ix 
 
Important Safety Instructions 
Read these instructions. Keep these instructions. Heed all warnings. Follow all 
instructions. Only use attachments/accessories specified by the manufacturer. 
Read and Retain Instructions 
Carefully read all safety and operating instructions before operating this equipment, 
and retain them for future reference.   
Follow Instructions and Heed Warnings 
Follow all operating and use instructions. Pay attention...

 
Important Safety Instructions 
x 78-4025112-01 Rev H0 
Know the following safety warnings and guidelines: 
 Dangerous Voltages 
- Only qualified service personnel are allowed to perform equipment 
installation or replacement. 
- Only qualified service personnel are allowed to remove chassis covers and 
access any of the components inside the chassis. 
 Grounding 
- Do not violate the protective grounding by using an extension cable, power 
cable, or autotransformer without a protective ground...

 
  Important Safety Instructions  
78-4025112-01 Rev H0 xi 
 
other equipment (including amplifiers) that produce heat. 
 Place this equipment close enough to a mains AC outlet to accommodate the 
length of this equipment’s power cord. 
 Route all power cords so that people cannot walk on, place objects on, or lean 
objects against them. This may pinch or damage the power cords. Pay particular 
attention to power cords at plugs, outlets, and the points where the power cords 
exit this equipment. 
...

 
Important Safety Instructions 
xii 78-4025112-01 Rev H0 
Elevated Operating Ambient Temperature 
Only install this equipment in a humidity- and temperature-controlled environment 
that meets the requirements given in this equipment’s technical specifications. 
 CAUTION: 
If installed in a closed or multi-unit rack assembly, the operating ambient 
temperature of the rack environment may be greater than room ambient 
temperature.  Therefore, install this equipment in an environment compatible 
with the...

 
  Important Safety Instructions  
78-4025112-01 Rev H0 xiii 
 
Note:  This plug fits only one way. If this plug cannot be fully inserted into the 
outlet, contact an electrician to replace the obsolete 3-terminal outlet. 
 Polarized Plug - For a 2-terminal plug (a polarized plug with one wide blade 
and one narrow blade), insert the plug into a polarized mains, 2-terminal outlet 
in which one socket is wider than the other. 
Note:  If this plug cannot be fully inserted into the outlet, try reversing...

 
Important Safety Instructions 
xiv 78-4025112-01 Rev H0 
equipment-rating label normally located close to the power inlet connector(s). 
 This equipment may have two power sources. Be sure to disconnect all power 
sources before working on this equipment. 
 If this equipment does not have a main power switch, the power cord connector 
serves as the disconnect device. 
 Always pull on the plug or the connector to disconnect a cable. Never pull on the 
cable itself. 
 Unplug this equipment when...

 
  Important Safety Instructions  
78-4025112-01 Rev H0 xv 
 
equipment during service and repair, do not wear electrically conducting objects 
such as a wristwatch or jewelry. 
 Lightning - Do not work on this equipment, or connect or disconnect cables, 
during periods of lightning. 
 Labels - Do not remove any warning labels. Replace damaged or illegible 
warning labels with new ones. 
 Covers - Do not open the cover of this equipment and attempt service unless 
instructed to do so in the...

 
Important Safety Instructions 
xvi 78-4025112-01 Rev H0 
 Insert batteries correctly. There may be a risk of explosion if the batteries are 
incorrectly inserted. 
 Do not attempt to recharge ‘disposable’ or ‘non-reusable’ batteries. 
 Please follow instructions provided for charging ‘rechargeable’ batteries. 
 Replace batteries with the same or equivalent type recommended by 
manufacturer. 
 Do not expose batteries to temperatures above 100°C (212°F). 
Disposal 
 The batteries may contain...

 
  Important Safety Instructions  
78-4025112-01 Rev H0 xvii 
 
Electromagnetic Compatibility Regulatory Requirements 
This equipment meets applicable electromagnetic compatibility (EMC) regulatory 
requirements. See this equipments data sheet for details about regulatory 
compliance approvals. EMC performance is dependent upon the use of correctly 
shielded cables of good quality for all external connections, except the power source, 
when installing this equipment. 
 Ensure compliance with...

 
Important Safety Instructions 
xviii 78-4025112-01 Rev H0