Cisco Dpq3925x User Manual
Have a look at the manual Cisco Dpq3925x User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 53 Cisco manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
4021193 Rev C 91 Monitor Gateway Status Section Field Description Internet Connection IP Address Displays the IP address of the WAN interface. This address is assigned to the gateway when it goes online. Subnet Mask Displays the subnet mask for your WAN port. This address is automatically assigned to your WAN port by your ISP except when a static IP address is set up. Default Gateway The IP address of the ISPs Default Gateway. DNS1-3 The DNS IP addresses currently used by the gateway. WINS The WINS IP address currently used by the gateway. Status > Local Network The Local Network Status page displays information about the status of the local area network. Select the Local Network tab to open the Status Local Network page. Click Refresh to update the data on the page. Use the following table to review the status of your gateway and your Internet connection. Section Field Description Local Network MAC Address A unique alphanumeric address for the private LAN home network.
92 4021193 Rev C Monitor Gateway Status Section Field Description A MAC address is a hardware address that uniquely identifies each node of a network. IP Address Displays the IP address for the LAN subnet Subnet Mask Displays the subnet mask for your LAN DHCP Server Displays the status of your local DHCP server (Enabled or Disabled) Starting IP Address Displays the beginning of the range of IP addresses used by the DHCP server in your gateway End IP Address Displays the end of the range of IP addresses used by the DHCP server DHCP Client Table Click DHCP Client Table to show which devices are attached to your LAN that have been issued IP addresses by the DHCP server in the gateway. On the DHCP Client Table page, you will see a list of DHCP clients (computers and other network devices) with the following information: Client Host Names, IP Addresses, MAC Addresses, and the length of time before their assigned IP addresses expire. To retrieve the most up-to-date information, click Refresh. To exit this page and return to the Local Network page, click Close. The following illustration shows an example of the DHCP Client Table.
4021193 Rev C 93 Monitor Gateway Status ARP/RARP Table Click ARP/RARP Table to see a complete list of all devices that are connected to your network. To retrieve the most up-to-date information, click Refresh. To exit this page and return to the Local Network page, click Close. The following illustration shows an example of the ARP/RARP Table. Status > Wireless The Wireless Network Status page displays basic information about the wireless network of the gateway. Select the Wireless tab to open the Status Wireless page. Click Refresh to update the data on the page.
94 4021193 Rev C Monitor Gateway Status Status Wireless Page Description Use the following table to review the status of your wireless network. Section Field Description Wireless Network MAC Address Displays the MAC Address of your gateways local wireless access point Radio Band Displays one of the following radio band frequencies currently in operation: 2.4 GHz 5 GHz 2.4 and 5 GHz Note: Not all products support the 5 GHz radio band. Network Name (SSID) Displays the name or service set identifier (SSID) of your wireless access point Channel Width Displays the channel bandwidth setting selected on the Basic Wireless Settings page Wide Channel Displays the Wide Channel setting selected on the Basic Wireless Settings page Standard Channel Displays the Standard Channel setting selected on the Basic Wireless Settings page Security Displays the security method used by your wireless network SSID Broadcast Displays the status of the gateways SSID Broadcast feature
4021193 Rev C 95 Monitor Gateway Status Status > DOCSIS WAN DOCSIS WAN Status displays information about the system of your cable modem. Select the DOCSIS WAN tab to open the Status DOCSIS WAN page. DOCSIS WAN Page Description Use the descriptions in the following table to review the status of your DOCSIS WAN network. Section Field Description About Model Displays the name of the residential gateway Vendor Displays the manufacturer of the residential gateway Hardware Revision Displays the revision of the circuit board design Serial Number Displays the unique serial of the residential gateway
96 4021193 Rev C Monitor Gateway Status Section Field Description MAC Address (CM MAC Address) Displays the CM MAC Address. The CM MAC Address is a unique alphanumeric address for the cable modem coaxial interface, which is used to connect to the CMTS at the headend. A MAC address is a hardware address that uniquely identifies each node of a network. Bootloader Revision Displays the boot revision code version Current Software Revision Displays the revision version of the firmware Firmware Name Displays the name of the firmware Firmware Build Time Displays the date and time the firmware was built Cable Modem Status Displays one of the possible current states of the gateway Downstream Channels Channels 1-8 Displays the power level and the signal to noise ratio of the active downstream channels Upstream Channels Channels 1-4 Displays the power level of the active upstream channels
4021193 Rev C 97 Frequently Asked Questions Frequently Asked Questions Q. How Do I Configure TCP/IP Protocol? A. To configure TCP/IP protocol, you need to have an Ethernet Network Interface Card (NIC) with TCP/IP communications protocol installed on your system. TCP/IP is a communications protocol used to access the Internet. This section contains instructions for configuring TCP/IP on your Internet devices to operate with the residential gateway in Microsoft Windows or Macintosh environments. TCP/IP protocol in a Microsoft Windows environment is different for each operating system. Follow the appropriate instructions in this section for your operating system. Configuring TCP/IP on Windows 2000 Systems 1 Click Start, select Settings, and choose Network and Dial-up Connections. 2 Double-click the Local Area Connection icon in the Network and Dial-up Connections window. 3 Click Properties in the Local Area Connection Status window. 4 Click Internet Protocol (TCP/IP) in the Local Area Connection Properties window, and then click Properties. 5 Select both Obtain an IP address automatically and Obtain DNS server address automatically in the Internet Protocol (TCP/IP) Properties window, and then click OK. 6 Click Yes to restart your computer when the Local Network window opens. The computer restarts. The TCP/IP protocol is now configured on your PC, and your Ethernet devices are ready for use. 7 Try to access the Internet. If you cannot access the Internet, contact your service provider for further assistance. Configuring TCP/IP on Windows XP Systems 1 Click Start, and depending on your Start menu setup, choose one of the following options: If you are using the Windows XP Default Start Menu, select Connect to, choose Show all connections, and then go to step 2. If you are using the Windows XP Classic Start Menu, select Settings, choose Network Connections, click Local Area Connection, and then go to step 3. 2 Double-click the Local Area Connection icon in the LAN or High-Speed Internet section of the Network Connections window. 3 Click Properties in the Local Area Connection Status window. 4 Click Internet Protocol (TCP/IP), and then click Properties in the Local Area Connection Properties window.
98 4021193 Rev C Frequently Asked Questions 5 Select both Obtain an IP address automatically and Obtain DNS server address automatically in the Internet Protocol (TCP/IP) Properties window, and then click OK. 6 Click Yes to restart your computer when the Local Network window opens. The computer restarts. The TCP/IP protocol is now configured on your PC, and your Ethernet devices are ready for use. 7 Try to access the Internet. If you cannot access the Internet, contact your service provider for further assistance. Configuring TCP/IP on Macintosh Systems 1 Click the Apple icon in the upper-left corner of the Finder. Scroll down to Control Panels, and then click TCP/IP. 2 Click Edit on the Finder at the top of the page. Scroll down to the bottom of the menu, and then click User Mode. 3 Click Advanced in the User Mode window, and then click OK. 4 Click the Up/Down selector arrows located to the right of the Connect Via section of the TCP/IP window, and then click Using DHCP Server. 5 Click Options in the TCP/IP window, and then click Active in the TCP/IP Options window. Note: Make sure that the Load only when needed option is unchecked. 6 Verify that the Use 802.3 option located in the upper-right corner of the TCP/IP window is unchecked. If there is a check mark in the option, uncheck the option, and then click Info in the lower-left corner. 7 Is there a Hardware Address listed in this window? If yes, click OK. To close the TCP/IP Control Panel window, click File, and then scroll down to click Close. You have completed this procedure. If no, you must power off your Macintosh. 8 With the power off, simultaneously press and hold down the Command (Apple), Option, P, and R keys on your keyboard. Keeping those keys pressed down, power on your Macintosh but do not release these keys until you hear the Apple chime at least three times, then release the keys and let the computer restart. 9 When your computer fully reboots, repeat steps 1 through 7 to verify that all TCP/IP settings are correct. If your computer still does not have a Hardware Address, contact your authorized Apple dealer or Apple technical support center for further assistance. Q. How Do I Renew the IP Address on My PC? A. If your PC cannot access the Internet after the residential gateway is online, it is possible that your PC did not renew its IP address. Follow the appropriate instructions in this section for your operating system to renew the IP address on your PC.
4021193 Rev C 99 Frequently Asked Questions Renewing the IP Address on Windows 95, 98, 98SE, and ME Systems 1 Click Start, and then click Run to open the Run window. 2 Type winipcfg in the Open field, and click OK to execute the winipcfg command. The IP Configuration window opens. 3 Click the down arrow to the right of the top field, and select the Ethernet adapter that is installed on your PC. The IP Configuration window displays the Ethernet adapter information. 4 Click Release, and then click Renew. The IP Configuration window displays a new IP address. 5 Click OK to close the IP Configuration window, you have completed this procedure. Note: If you cannot access the Internet, contact your service provider for further assistance. Renewing the IP Address on Windows NT, 2000, or XP Systems 1 Click Start, and then click Run. The Run window opens. 2 Type cmd in the Open field and click OK. A window with a command prompt opens. 3 Type ipconfig/release at the C:/ prompt and press Enter. The system releases the IP address. 4 Type ipconfig/renew at the C:/ prompt and press Enter. The system displays a new IP address. 5 Click the X in the upper-right corner of the window to close the Command Prompt window. You have completed this procedure. Note: If you cannot access the Internet, contact your service provider for further assistance. Q. What if I dont subscribe to cable TV? A. If cable TV is available in your area, data service may be made available with or without subscribing to cable TV service. Contact your local service provider for complete information on cable services, including high-speed Internet access. Q. How do I arrange for installation? A. Call your service provider to inquire about professional installation. A professional installation ensures proper cable connection to the modem and to your PC, and it ensures the proper configuration of all hardware and software settings. Contact your service provider for more information about installation.
100 4021193 Rev C Frequently Asked Questions Q. How does the residential gateway connect to my computer? A. The residential gateway connects to the PC using a wireless connection or the 10/100/1000BASE-T Ethernet port on your PC. If you want to use an Ethernet interface, Ethernet cards available from your local PC or office supply retailer, or from your service provider. For best performance over an Ethernet connection, your PC should be equipped with a Gigabit Ethernet card. Q. After my residential gateway is connected, how do I access the Internet? A. Your local service provider becomes your Internet Service Provider (ISP). They offer a wide range of services including e-mail, chat, news, and information services. Your service provider will provide the software you will need. Q. Can I watch TV and surf the Internet at the same time? A. Absolutely! If you subscribe to cable television service, you can watch TV and use your residential gateway at the same time by connecting your TV and your residential gateway to the cable network using an optional cable signal splitter. Common Troubleshooting Issues I dont understand the front panel status indicators See Front Panel LED Status Indicator Functions (on page 102), for more detailed information on front panel LED status indicator operation and function. The residential gateway does not register an Ethernet connection Verify that your computer has an Ethernet card and that the Ethernet driver software is properly installed. If you purchase and install an Ethernet card, follow the installation instructions very carefully. Verify the status of the front panel status indicator lights. The residential gateway does not register an Ethernet connection after connecting to a hub If you are connecting multiple PCs to the residential gateway, you should first connect the modem to the uplink port of the hub using the correct crossover cable. The LINK LED of the hub will illuminate continuously. The residential gateway does not register a cable connection The modem works with a standard 75-ohm RF coaxial cable. If you are using a different cable, your residential gateway will not function properly. Contact your cable service provider to determine whether you are using the correct cable. Your NIC card or USB interface may be malfunctioning. Refer to the troubleshooting information in the NIC or USB documentation.