Cisco C40 Manual

							D14636.12 Profile C60-C40 and Codec C60-C40 Administrator Guide TC6.3, OCTOBER 2013. www.cisco.com — Copyright © 2010-2013 Cisco Systems, Inc. All rights reser ved. 
81
Network [1..1] IPv6 Address
Enter the static IPv6 network address for the system. This setting is only applicable when the 
Network IPv6 Assignment is set to Static.
Requires user role:  ADMIN
Value space:  
Format:  A valid IPv6 address.
Example:
 Network 1 IP v6 Add ress: "2001:0DB8:0000:0000:0000:0000:0000:0002"
Network [1..1] IPv6 Gateway
Define the IPv6 network gateway address. This setting is only applicable when the Network 
IPv6 Assignment is set to Static.
Requires user role:  ADMIN
Value space:  
Format:  A valid IPv6 address.
Example:
 Network 1 IP v6 Gateway: "2001:0DB8:0000:0000:0000:0000:0000:0001"
Network [1..1] IPv6 DHCPOptions
Retrieve a set of DHCP options, for example NTP and DNS server addresses, from a DHCPv6 
server.
Requires user role:  ADMIN
Value space:  
Off:  Disable the retrieval of DHCP options from a DHCPv6 server.
On:  Enable the retrieval of a selected set of DHCP options from a DHCPv6 server.
Example:
 Network 1 IPv6 DHCPOptions: On
Network [1..1] DHCP RequestTFTPServerAddress
This setting is used only for video systems that are registered to a Cisco Unified 
Communications Manager (CUCM).
The setting determines whether the endpoint should ask the DHCP server for DHCP option 150, 
so that it can discover the address of the TFTP server (provisioning server) automatically.  
If this setting is Off or the DHCP server does not support option 150, the TFTP server address 
must be set manually using the Provisioning ExternalManager Address setting.
Note: If the Network VLAN Voice Mode setting is Auto and the Cisco Discovery Protocol (CDP) 
assigns an ID to the voice VLAN, then a request for option 150 will always be sent. That is, the 
Network DHCP RequestTFTFServerAddress setting will be ignored.
Requires user role:  ADMIN
Value space:  
Off:  The video system will not send a request for DHCP option 150 and the address of the 
TFTP server must be set manually. See the note above for any exception to this rule.
On:  The video system will send a request for option 150 to the DHCP server so that it can 
automatically discover the address of the TFTP server.
Example:
 Network 1 DHCP RequestTFTPServerAddress: On
Network [1..1] DNS Domain Name
DNS Domain Name is the default domain name suffix which is added to unqualified names.
Example: If the DNS Domain Name is "company.com" and the name to lookup is 
"MyVideoSystem", this will result in the DNS lookup "MyVideoSystem.company.com".
Requires user role:  ADMIN
Value space:  
Format:  String with a maximum of 64 characters.
Example:
 Network 1 DNS Domain Name: ""
Network [1..1] DNS Server [1..3] Address
Define the network addresses for DNS servers. Up to 3 addresses may be specified. If the 
network addresses are unknown, contact your administrator or Internet Service Provider.
Requires user role:  ADMIN
Value space:  
Format:  A valid IPv4 address or IPv6 address.
Example:
 Network 1 DNS Server 1 Address: ""
Cisco TelePresence System Codec C40/C60 and Profiles using C40/60 Administrator Guide  
						

							D14636.12 Profile C60-C40 and Codec C60-C40 Administrator Guide TC6.3, OCTOBER 2013. www.cisco.com — Copyright © 2010-2013 Cisco Systems, Inc. All rights reser ved. 
82
Network [1..1] QoS Mode
The QoS (Quality of Service) is a method which handles the priority of audio, video and data in 
the network. The QoS settings must be supported by the infrastructure. Diffserv (Differentiated 
Services) is a computer networking architecture that specifies a simple, scalable and coarse-
grained mechanism for classifying, managing network traffic and providing QoS priorities on 
modern IP networks.
Requires user role:  ADMIN
Value space:  
Off:  No QoS method is used. 
Diffserv:  When you set the QoS Mode to Diffserv, the Network QoS Diffserv Audio, Network 
QoS Diffserv Video, Network QoS Diffserv Data, Network QoS Diffserv Signalling, Network 
QoS Diffserv ICMPv6 and Network QoS Diffserv NTP settings are used to prioritize packets.
Example:
 Network 1 QoS Mode: Diffserv
Network [1..1] QoS Diffserv Audio
Note: This setting will only take effect if Network QoS Mode is set to Diffserv.
Define which priority Audio packets should have in the IP network.
The priority for the packets ranges from 0 to 63 - the higher the number, the higher the priority. 
The recommended class for Audio is CS4, which equals the decimal value 32. If in doubt, 
contact your network administrator.
The priority set here might be overridden when packets are leaving the network controlled by 
the local network administrator.
Requires user role:  ADMIN
Value space:  
Range:  Select a value between 0 to 63 - the higher the number, the higher the priority. The 
default value is 0 (best effort).
Example:
 Network 1 QoS Diffserv Audio: 0
Network [1..1] QoS Diffserv Video
Note: This setting will only take effect if Network QoS Mode is set to Diffserv.
Define which priority Video packets should have in the IP network. The packets on the 
presentation channel (shared content) are also in the Video packet category. 
The priority for the packets ranges from 0 to 63 - the higher the number, the higher the priority. 
The recommended class for Video is CS4, which equals the decimal value 32. If in doubt, 
contact your network administrator.
The priority set here might be overridden when packets are leaving the network controlled by 
the local network administrator.
Requires user role:  ADMIN
Value space:  
Range:  Select a value between 0 to 63 - the higher the number, the higher the priority. The 
default value is 0 (best effort).
Example:
 Network 1 QoS Diffserv Video: 0
Network [1..1] QoS Diffserv Data
Note: This setting will only take effect if Network QoS Mode is set to Diffserv.
Define which priority Data packets should have in the IP network. 
The priority for the packets ranges from 0 to 63 - the higher the number, the higher the priority. 
The recommended value for Data is 0, which means best effort. If in doubt, contact your 
network administrator.
The priority set here might be overridden when packets are leaving the network controlled by 
the local network administrator.
Requires user role:  ADMIN
Value space:  
Range:  Select a value between 0 to 63 - the higher the number, the higher the priority. The 
default value is 0 (best effort).
Example:
 Network 1 QoS Diffserv Data: 0
Cisco TelePresence System Codec C40/C60 and Profiles using C40/60 Administrator Guide  
						

							D14636.12 Profile C60-C40 and Codec C60-C40 Administrator Guide TC6.3, OCTOBER 2013. www.cisco.com — Copyright © 2010-2013 Cisco Systems, Inc. All rights reser ved. 
83
Network [1..1] QoS Diffserv Signalling
Note: This setting will only take effect if Network QoS Mode is set to Diffserv.
Define which priority Signalling packets that are deemed critical (time-sensitive) for the real-
time operation should have in the IP network. 
The priority for the packets ranges from 0 to 63 - the higher the number, the higher the priority. 
The recommended class for Signalling is CS3, which equals the decimal value 24. If in doubt, 
contact your network administrator.
The priority set here might be overridden when packets are leaving the network controlled by 
the local network administrator.
Requires user role:  ADMIN
Value space:  
Range:  Select a value between 0 to 63 - the higher the number, the higher the priority. The 
default value is 0 (best effort).
Example:
 Network 1 QoS Diffserv Signalling: 0
Network [1..1] QoS Diffserv ICMPv6
Note: This setting will only take effect if Network QoS Mode is set to Diffserv.
Define which priority ICMPv6 packets should have in the IP network. 
The priority for the packets ranges from 0 to 63 - the higher the number, the higher the priority. 
The recommended value for ICMPv6 is 0, which means best effort. If in doubt, contact your 
network administrator.
The priority set here might be overridden when packets are leaving the network controlled by 
the local network administrator.
Requires user role:  ADMIN
Value space:  
Range:  Select a value between 0 to 63 - the higher the number, the higher the priority. The 
default value is 0 (best effort).
Example:
 Network 1 QoS Diffserv ICMPv6: 0
Network [1..1] QoS Diffserv NTP
Note: This setting will only take effect if Network QoS Mode is set to Diffserv.
Define which priority NTP packets should have in the IP network. 
The priority for the packets ranges from 0 to 63 - the higher the number, the higher the priority. 
The recommended value for NTP is 0, which means best effort. If in doubt, contact your 
network administrator.
The priority set here might be overridden when packets are leaving the network controlled by 
the local network administrator.
Requires user role:  ADMIN
Value space:  
Range:  Select a value between 0 to 63 - the higher the number, the higher the priority. The 
default value is 0 (best effort).
Example:
 Network 1 QoS Diffserv NTP: 0
Network [1..1] IEEE8021X Mode
The system can be connected to an IEEE 802.1X LAN network, with a port-based network 
access control that is used to provide authenticated network access for Ethernet networks.
Requires user role:  ADMIN
Value space:  
Off:  The 802.1X authentication is disabled (default).
On:  The 802.1X authentication is enabled.
Example:
 Network 1 IEEE8021X Mode: Off
Cisco TelePresence System Codec C40/C60 and Profiles using C40/60 Administrator Guide  
						

							D14636.12 Profile C60-C40 and Codec C60-C40 Administrator Guide TC6.3, OCTOBER 2013. www.cisco.com — Copyright © 2010-2013 Cisco Systems, Inc. All rights reser ved. 
84
Network [1..1] IEEE8021X TlsVerify
Verification of the server-side certificate of an IEEE802.1x connection against the certificates in 
the local CA-list when TLS is used. The CA-list must be uploaded to the video system. This can 
be done from the web interface.
This setting takes effect only when Network [1..1] IEEE8021X Eap Tls is enabled (On).
Requires user role:  ADMIN
Value space:  
Off:  When set to Off, TLS connections are allowed without verifying the server-side X.509 
certificate against the local CA-list. This should typically be selected if no CA-list has been 
uploaded to the codec.
On:  When set to On, the server-side X.509 certificate will be validated against the local CA-
list for all TLS connections. Only servers with a valid certificate will be allowed.
Example:
 Network 1 IEEE8021X TlsVerify: Off
Network [1..1] IEEE8021X UseClientCertificate
Authentication using a private key/certificate pair during an IEEE802.1x connection. The 
authentication X.509 certificate must be uploaded to the video system. This can be done from 
the web interface.
Requires user role:  ADMIN
Value space:  
Off:  When set to Off client-side authentication is not used (only server-side).
On:  When set to On the client (video system) will perform a mutual authentication TLS 
handshake with the server.
Example:
 Network 1 IEEE8021X UseClientCertificate: Off
Network [1..1] IEEE8021X Identity
The 802.1X Identity is the user name needed for 802.1X authentication.
Requires user role:  ADMIN
Value space:  
Format:  String with a maximum of 64 characters. 
Example:
 Network 1 IEEE8021X Identity: ""
Network [1..1] IEEE8021X Password
The 802.1X Password is the password needed for 802.1X authentication.
Requires user role:  ADMIN
Value space:  
Format:  String with a maximum of 32 characters.
Example:
 Network 1 IEEE8021X Password: ""
Network [1..1] IEEE8021X AnonymousIdentity
The 802.1X Anonymous ID string is to be used as unencrypted identity with EAP (Extensible 
Authentication Protocol) types that support different tunneled identity, like EAP-PEAP and EAP-
T TLS. If set, the anonymous ID will be used for the initial (unencrypted) EAP Identity Request.
Requires user role:  ADMIN
Value space:  
Format:  String with a maximum of 64 characters.
Example:
 Network 1 IEEE8021X Anony mousIdentity: ""
Network [1..1] IEEE8021X Eap Md5
Set the Md5 (Message-Digest Algorithm 5) mode. This is a Challenge Handshake 
Authentication Protocol that relies on a shared secret. Md5 is a Weak security.
Requires user role:  ADMIN
Value space:  
Off:  The EAP-MD5 protocol is disabled.
On:  The EAP-MD5 protocol is enabled (default).
Example:
 Network 1 IEEE8021X Eap Md5: On
Cisco TelePresence System Codec C40/C60 and Profiles using C40/60 Administrator Guide  
						

							D14636.12 Profile C60-C40 and Codec C60-C40 Administrator Guide TC6.3, OCTOBER 2013. www.cisco.com — Copyright © 2010-2013 Cisco Systems, Inc. All rights reser ved. 
85
Network [1..1] IEEE8021X Eap Ttls
Set the T TLS (Tunneled Transport Layer Security) mode. Authenticates LAN clients without the 
need for client certificates. Developed by Funk Software and Certicom. Usually supported by 
Agere Systems, Proxim and Avaya. 
Requires user role:  ADMIN
Value space:  
Off:  The EAP-T TLS protocol is disabled.
On:  The EAP-T TLS protocol is enabled (default).
Example:
 Network 1 IEEE8021X Eap Ttls: On
Network [1..1] IEEE8021X Eap Tls
Enable or disable the use of EAP-TLS (Transport Layer Security) for IEEE802.1x connections. 
The EAP-TLS protocol, defined in RFC 5216, is considered one of the most secure EAP 
standards. LAN clients are authenticated using client certificates.
Requires user role:  ADMIN
Value space:  
Off:  The EAP-TLS protocol is disabled.
On:  The EAP-TLS protocol is enabled (default).
Example:
 Network 1 IEEE8021X Eap Tls: On
Network [1..1] IEEE8021X Eap Peap
Set the Peap (Protected Extensible Authentication Protocol) mode. Authenticates LAN clients 
without the need for client certificates. Developed by Microsoft, Cisco and RSA Security.
Requires user role:  ADMIN
Value space:  
Off:  The EAP-PEAP protocol is disabled.
On:  The EAP-PEAP protocol is enabled (default).
Example:
 Network 1 IEEE8021X Eap Peap: On
Network [1..1] MTU
Set the Ethernet MTU (Maximum Transmission Unit).
Requires user role:  ADMIN
Value space:  < 5 7 6 . .15 0 0 >
Range:  Select a value from 576 to 1500 bytes.
Example:
 Network 1 MTU: 1500
Network [1..1] Speed
Set the Ethernet link speed.
NOTE: If running older software versions than TC6.0, restart the system for any change to this 
setting to take effect.
Requires user role:  ADMIN
Value space:  < A u to/10 h a l f/10 f u l l/10 0 h a l f/10 0 f u l l/10 0 0 f u l l>
Auto:  Autonegotiate link speed.
10 h a l f :  Force link to 10 Mbps half-duplex.
10 f u l l:  Force link to 10 Mbps full-duplex.
10 0 h a l f :  Force link to 100 Mbps half-duplex.
10 0 f u l l:  Force link to 100 Mbps full-duplex.
1000full:  Force link to 1 Gbps full-duplex.
Example:
 Network 1 Speed: Auto
Network [1..1] TrafficControl Mode
Set the network traffic control mode to decide how to control the video packets transmission 
speed.
Requires user role:  ADMIN
Value space:  
Off:  Transmit video packets at link speed.
On:  Transmit video packets at maximum 20 Mbps. Can be used to smooth out bursts in the 
outgoing network traffic.
Example:
 Network 1 TrafficControl: On
Cisco TelePresence System Codec C40/C60 and Profiles using C40/60 Administrator Guide  
						

							D14636.12 Profile C60-C40 and Codec C60-C40 Administrator Guide TC6.3, OCTOBER 2013. www.cisco.com — Copyright © 2010-2013 Cisco Systems, Inc. All rights reser ved. 
86
Network [1..1] RemoteAccess Allow
Filter IP addresses for access to ssh/telnet/HT TP/HT TPS.
Requires user role:  ADMIN
Value space:  
Format:  String with a maximum of 255 characters, comma separated IP adresses or IP 
range.
Example:
 N e t w o r k  1  R e m o t e A c c e s s  A l l o w:  "19 2.16 8.1.2 31,  19 2.16 8.1.18 2 "
Network [1..1] VLAN Voice Mode
Set the VLAN voice mode. The VLAN Voice Mode will be set to Auto automatically if you 
choose Cisco UCM (Cisco Unified Communications Manager) as provisioning infrastructure via 
the Provisioning Wizard on the Touch controller.
Requires user role:  ADMIN
Value space:  
Auto:  The Cisco Discovery Protocol (CDP), if available, assigns an id to the voice VLAN. If 
CDP is not available, VLAN is not enabled. 
Manual:  The VLAN ID is set manually using the Network VLAN Voice VlanId setting. If CDP is 
available, the manually set value will be overruled by the value assigned by CDP.
Off:  VLAN is not enabled.
Example:
 Network 1 VLAN Voice Mode: Off
Network [1..1] VLAN Voice VlanId
Set the VLAN voice ID. This setting will only take effect if VLAN Voice Mode is set to Manual.
Requires user role:  ADMIN
Value space:  
Range:  Select a value from 1 to 4094.
Example:
 Network 1 VLAN Voice VlanId: 1
Cisco TelePresence System Codec C40/C60 and Profiles using C40/60 Administrator Guide  
						

							D14636.12 Profile C60-C40 and Codec C60-C40 Administrator Guide TC6.3, OCTOBER 2013. www.cisco.com — Copyright © 2010-2013 Cisco Systems, Inc. All rights reser ved. 
87
NetworkPort settings
NetworkPort [2] Mode
Define if the network port 2 shall be enabled for direct pairing with a Cisco TelePresence Touch 
controller.
NOTE: Restart the system for any change to this setting to take effect.
Requires user role:  ADMIN
Value space:  
Inactive:  Set the NetworkPort 2 to Inactive when no device is connected.
DirectPairing:  Set the NetworkPort 2 to DirectPairing when you have a Cisco TelePresence 
Touch controller connected to the port. This will enable for direct pairing between the Touch 
controller and the codec.
Example:
 NetworkPort 2 Mode: Inactive
Cisco TelePresence System Codec C40/C60 and Profiles using C40/60 Administrator Guide  
						

							D14636.12 Profile C60-C40 and Codec C60-C40 Administrator Guide TC6.3, OCTOBER 2013. www.cisco.com — Copyright © 2010-2013 Cisco Systems, Inc. All rights reser ved. 
88
NetworkServices settings
NetworkServices H323 Mode
Determine whether the system should be able to place and receive H.323 calls or not.
Requires user role:  ADMIN
Value space:  
Off:  Disable the possibility to place and receive H.323 calls.
On:  Enable the possibility to place and receive H.323 calls (default).
Example:
 NetworkServices H323 Mode: On
NetworkServices HTTP Mode
Set the HT TP mode to enable/disable access to the system through a web browser. The web 
interface is used for system management, call management such as call transfer, diagnostics 
and software uploads.
NOTE: Restart the system for any change to this setting to take effect.
Requires user role:  ADMIN
Value space:  
Off:  The HT TP protocol is disabled.
On:  The HT TP protocol is enabled.
Example:
 NetworkServices HTTP Mode: On
NetworkServices SIP Mode
Determine whether the system should be able to place and receive SIP calls or not.
Requires user role:  ADMIN
Value space:  
Off:  Disable the possibility to place and receive SIP calls.
On:  Enable the possibility to place and receive SIP calls (default).
Example:
 NetworkServices SIP Mode: On
NetworkServices Telnet Mode
Telnet is a network protocol used on the Internet or Local Area Network (LAN) connections.
Requires user role:  ADMIN
Value space:  
Off:  The Telnet protocol is disabled. This is the factory setting.
On:  The Telnet protocol is enabled.
Example:
 NetworkServices Telnet Mode: Off
NetworkServices WelcomeText
Choose which information the user should see when logging on to the codec through Telnet/
SSH.
Requires user role:  ADMIN
Value space:  
Off:  The welcome text is: Login successful
On:  The welcome text is: Welcome to ; Software version; Software release 
date; Login successful.
Example:
 NetworkServices WelcomeText: On
NetworkServices XMLAPI Mode
Enable or disable the video system's XML API. For security reasons this may be disabled. 
Disabling the XML API will limit the remote manageability with for example TMS, which no 
longer will be able to connect to the video system.
Requires user role:  ADMIN
Value space:  
Off:  The XML API is disabled.
On:  The XML API is enabled (default).
Example:
 NetworkServices XMLAPI Mode: On
Cisco TelePresence System Codec C40/C60 and Profiles using C40/60 Administrator Guide  
						

							D14636.12 Profile C60-C40 and Codec C60-C40 Administrator Guide TC6.3, OCTOBER 2013. www.cisco.com — Copyright © 2010-2013 Cisco Systems, Inc. All rights reser ved. 
89
NetworkServices MultiWay Address
The MultiWay address must be equal to the Conference Factory Alias, as configured on the 
Video Communication Server. The Multiway™ conferencing enables video endpoint users to 
introduce a 3rd party into an existing call.
Multiway™ can be used in the following situations:
1) When you want to add someone else in to your existing call.
2) When you are called by a 3rd party while already in a call and you want to include that person 
in the call.
Requirements: The Codec C60/C40 must run software version TC4.0 (or later), Video 
Communication Server (VCS) version X5 (or later) and Codian MCU version 3.1 (or later). Video 
systems invited to join the Multiway™ conference must support the H.323 routeToMC facility 
message if in an H.323 call, or SIP REFER message if in a SIP call.
Requires user role:  ADMIN
Value space:  
Format:  String with a maximum of 255 characters (a valid dial URI).
Example:
 NetworkServices MultiWay Address: "h323:[email protected]"
NetworkServices MultiWay Protocol
Determine the protocol to be used for MultiWay calls.
Requires user role:  ADMIN
Value space:  
Auto:  The system will select the protocol for MultiWay calls.
H323:  The H323 protocol will be used for MultiWay calls.
Sip:  The SIP protocol will be used for MultiWay calls.
Example:
 NetworkServices MultiWay Protocol: Auto
NetworkServices HTTPS Mode
HT TPS is a web protocol that encrypts and decrypts user page requests as well as the pages 
that are returned by the web server.
NOTE: Restart the system for any change to this setting to take effect.
Requires user role:  ADMIN
Value space:  
Off:  The HT TPS protocol is disabled.
On:  The HT TPS protocol is enabled.
Example:
 NetworkServices HTTPS Mode: On
NetworkServices HTTPS VerifyServerCertificate
When the video system connects to an external HT TPS server (like a phone book server or an 
external manager), this server will present a certificate to the video system to identify itself.
Requires user role:  ADMIN
Value space:  
Off:  Do not verify server certificates.
On:  Requires the system to verify that the server certificate is signed by a trusted Certificate 
Authority (CA). This requires that a list of trusted CAs are uploaded to the system in advance.
Example:
 NetworkServices HTTPS VerifyServerCertificate: Off
NetworkServices HTTPS VerifyClientCertificate
When the video system connects to a HT TPS client (like a web browser), the client can be 
asked to present a certificate to the video system to identify itself. 
Requires user role:  ADMIN
Value space:  
Off:  Do not verify client certificates.
On:  Requires the client to present a certificate that is signed by a trusted Certificate 
Authority (CA). This requires that a list of trusted CAs are uploaded to the system in advance.
Example:
 NetworkServices HTTPS VerifyClientCertificate: Off
Cisco TelePresence System Codec C40/C60 and Profiles using C40/60 Administrator Guide  
						

							D14636.12 Profile C60-C40 and Codec C60-C40 Administrator Guide TC6.3, OCTOBER 2013. www.cisco.com — Copyright © 2010-2013 Cisco Systems, Inc. All rights reser ved. 
90
NetworkServices HTTPS OCSP Mode
Define the support for OCSP (Online Certificate Status Protocol) responder services. The OCSP 
feature allows users to enable OCSP instead of certificate revocation lists (CRLs) to check the 
certificate status.
For any outgoing HT TPS connection, the OCSP responder is queried of the status. If the 
corresponding certificate has been revoked, then the HT TPS connection will not be used.
Requires user role:  ADMIN
Value space:  
Off:  Disable OCSP support.
On:  Enable OCSP support.
Example:
 NetworkServices HTTPS OCSP Mode: Off
NetworkServices HTTPS OCSP URL
Specify the URL of the OCSP responder (server) that will be used to check the certificate 
status.
Requires user role:  ADMIN
Value space:  
Format:  String with a maximum of 255 characters.
Example:
 NetworkServices HTTPS OCSP URL: "http://ocspserver.company.com:81"
NetworkServices NTP Mode
The Network Time Protocol (NTP) is used to synchronize the time of the system to a reference 
time server. The time server will subsequently be queried every 24th hour for time updates. 
The time will be displayed on the top of the screen. The system will use the time to timestamp 
messages transmitted to Gatekeepers or Border Controllers requiring H.235 authentication. 
The system will use the time to timestamp messages transmitted to Gatekeepers or Border 
Controllers that requires H.235 authentication. It is also used for timestamping Placed Calls, 
Missed Calls and Received Calls.
Requires user role:  ADMIN
Value space:  
Auto:  The system will use the NTP server, by which address is supplied from the DHCP 
server in the network. If no DHCP server is used, or the DHCP server does not provide 
the system with a NTP server address, the system will use the static defined NTP server 
address specified by the user.
Off:  The system will not use an NTP server.
Manual:  The system will always use the static defined NTP server address specified by the 
u s e r.
Example:
 NetworkServices NTP Mode: Manual
NetworkServices NTP Address
Enter the NTP Address to define the network time protocol server address. This address will 
be used if NTP Mode is set to Manual, or if set to Auto and no address is supplied by a DHCP 
server.
Requires user role:  ADMIN
Value space:  
Format:  A valid IPv4 address, IPv6 address or DNS name.
Example:
 NetworkServices NTP Address: "1.ntp.tand berg.com"
Cisco TelePresence System Codec C40/C60 and Profiles using C40/60 Administrator Guide