Cine Versum Cineversum Projector Lv Xg6k User Manual

50
Note:
Keep from dust and smog.
Otherwise, the image quality may deteriorate.
Whenoperated in an environment
with dust and smog, the dust and dirt will
accumulate on its lens, liquid crystal board or
the lens assembly inside the projector. If that
happens, you should contact the local
distributor or repair center for correct
cleaning.
Maintenance
Cleaning the filter
The filter prevents dust from accumulating on the surface of lens assembly.Should the
filter become clogged with dust particles, it...

51
Maintenance
Covering the lens properly
If needs to be moved or won’t be used for
extended period of time, you should cover the lens
properly.
Cleaning the lens
Unplug the AC power cord before cleaning.
Apply some non-abrasive cleaning agent exclusively
designed for cameras onto a piece of clean cloth, and then
use it to wipe the lens ge ntly. Or you can use cleaning
paper or commercial blower to clean the lens.
Avoid excessive use of cleaning agent. Abrasive cleaning
agent, solvent or other coarse...

52
To replace the lamp, follow the steps below:
1. Power off the projector and unplug the power
cord. Then let the project cool for at least 45
minutes.
2. Loosen the screws on the lamp cover and open
the cover.
3. Make sure the lamp is well protected and
remove two screws. Hold the handle and pull
out the lamp.
4. Install a new lamp with the same model and
tighten the two screws. Make sure the
installation is correct. Put lamp cover in place
and then tighten the screws.
5. Plug the AC power cord and...

53

½Ö
Maintenance
Changing the lamp model
Purchasing new lamps
Users can buy new lamps through the local distributor. Your purchase order should include the
information below:
Lamp model
This projector uses a high-pressure lamp which must be handled carefully and properly.
Improper handling may result in accidents, injury, or create a fire hazard.

”Lamp life may differ from lamp to lamp and according to the environment of use. There is no guarantee
of the same life for each lamp....

54
Appendix
Troubleshooting
Before you contact the local distributor or repair center, you may check the items below once again.
-Make sure you have properly connected to the peripheral equipment.
-Make sure all equipment has been connected to AC power source and the power source is in ON state.
-If it can’t project image output from a PC, please re-start the PC.
n o i t u l o S
e r u l i a F
Machine can’t be powered on -Plug the power cord of the projector into the AC power outlet.
-Check whether the...

55
Appendix
No image -Check the connection between PC or video equipment
-Check with the signal from PC is correct. If connected to
certain laptops, the settings of their video adapters need to be changed.
You can refer to the operating instructions of the PC for such
modification.
-Images can show up only about 10 seconds after the projector is
powered on.
-Check the input signal, color system, video system or PC system mode.
-Make sure that the temperature doesn’t exceedthe permitted oper
ating...

56
Appendix
Distorted image or no image
-Check and adjust the PC menu or on-screen menu.
The PIN code dialog box popes up in the
startup
process-A PIN code is set for locking.
Remote control doesn’t work-Check the battery.
-Make sure there is no obstacle
between the projector and the remote control.
-To use the remote control, keep it within 5 meters away from the
projector.
-Make sure the code of the remote
control is consistent with the projector.
-Unlock the key through the setup menu.
The indi
cator...

57
POWERWARNINGLAMPSHIFTFOCUS
?
?
green
red
yellowoff
green flashgreen flash
*When the projector bulbreaches its endurance, the indicator light will be yellow and you need to
change the bulb.
Appendix
Indicator and projector state
Check the indicator to know about the state of projector.
Indicator
(Green/red) (Red) (Yellow) (Blue)(Green)
State of projector
Is in power-off state (AC power cord not
inserted).
Is in standby state. Press ON/STNADBY to
power on the projector.
Is in normal working state.
Is...

58
3
640x400 601152x900 65
640x400 701152x900 75
640x400 851280x1024 60
640x480 601280x1024 65
640x480 651280x1024 70
640x480 721280x1024 72
640x480 751280x1024 75
640x480 851280x1024 85
800x600 50WXGA 1280x768 60
800x600 601280x768 75
800x600 651280x768 85
800x600 721280x768 120
800x600 751360x768 60
800x600 851360x768 72
800x600 1201366x768 60
832x624 751280x800 60
XGA 1024x768 601280x800 75
1024x768 651280x800 85
1024x768 701280x800 120
1024x768 721080psf241920x1080 24
1024x768 751080psf251920x1080...

59
512341096781514131112
-----
1
5
2
4
3
6
7
8
-----9
13
10
12
11
14
15
RX –
TX +
TX –
RX +
2
3
4
87654321
5
6
7
8
1-----
-----
----------
-----
R X D
T X D
-----
GND
-----
1
2
3
4
5
6
7
8
-----9
-----
-----
PINcodememorandum
Write down the PIN code in the blank below and keep it,
please contact the repair center.
PIN code lock
*If this 3-digit number is changed,
the factory
default number will be ineffective. Factory default PIN code 111*
Factory default PIN code 111*
Locking startup-animation PIN code...