Cine Versum Cineversum Blackwing Three User Manual

							2.0  BASIC OPERATION
R599751 - Master Three User Manual 11 
To install the remote control batteries:
1) Locate the battery compartment on the back of the remote control.
2) Remove the cover from the back. To do this, press the tab attached to the cover and pull the cover with the
guide on the back of the remote control.
3) Remove the old batteries (if applicable).
4) Insert two new AA batteries in the compartment as shown on the inside of the battery compartment. Make sure
the batteries are correctly inserted, observing the proper polarity.
5) After installation, replace the cover and dispose of the old batteries (if applicable).
Menu Navigation
You can control the Master Three as follows:
•From the front panel controls
•From the remote control
•From a programmed universal remote control
•Using the serial connection on the back panel
The menu navigation controls on the remote control are duplicated on the front panel of the Master Three.
To navigate the menu:
1) Press the Menu button.
2) Use the directional buttons to highlight the parameter you want to change.
3) Press the Enter button to select the parameter and the Left and Right arrow buttons to change the chosen
parameter.
4) Press the Exit button to exit out of the menu/OSD.
Info Screen Button
Press the Info button to display a window that shows information about the system including:
Input Status
Video Source
Signal Type
Audio Source
Aspect Ratio (Frame/Active)
Output Status
Resolution
Frame Rate
Line Rate
Aspect Ratio (Display/Screen)
This screen can be helpful during troubleshooting. 
						

							3.0  SETUP
12 R599751 - Master Three User Manual
3.0 SETUP
3.1 Initial Set-Up
Once you have installed the Master Three into your system, you must properly configure it for the display device
being driven. The Master Three is shipped from the factory with the following preset default settings:
•Input Select is set to AUTO, to automatically detect an active input in a pre-configured priority.
•The Digital Video output is selected with RGB 4:4:4 color space
•The output format is set to SMPTE 274M, 1080p@50Hz or 1080p@60Hz according to the active source refresh
rate.
Use either the remote control or the front panel controls to perform the initial setup of the Master Three's output. The
procedure below uses the front panel buttons to perform initial setup.
Accessing the Master Three’s OSD is crucial, not only in allowing you to navigate the menu of the Master Three, but
also to let you know that the Master Three is sending a compatible signal to the display. If the OSD is not visible on
the display’s screen when you press one of the sub-menu buttons on the remote control, then you must configure
the Master Three with the Output Setup menu to output a signal that the display can accept.
Use these steps to allow you to see the OSD.
STEP 1 - Power Up
1) Attach the removable power cord to the external power supply.
2) Plug the removable power cord into a wall outlet or power conditioner, if applicable.
3) Plug the small connector attached to the cable that comes out of the power supply into the Master Three.
The Master Three should power on and display ‘CineVERSUM Powered by ABT’ on the FPD.
STEP 2 - Connect the scaler to your display 
Displays with a DVI or HDMI Input
The default output on the Master Three is digital RGB 4:4:4 (DVI Standard). If you have changed this setting, follow
these instructions to change the settings back.
1) Press the Menu button on the front panel of the Master Three once. You should see ‘Main Menu /Input Select’
on the FPD.
2) Press the Up button once. You should see ‘Main Menu / Output Setup’ on the FPD.
3) Press the Enter button. You should see ‘Output Setup / Analog/Digital’ on the FPD.
4) Press the Enter button. You should see ‘Analog/Digital / BNC (Analog)’.
5) Press the Down button to select ‘HDMI (Digital)’ and press the Enter button.
You should see the Master Three’s On Screen Display (OSD) on your screen.
Displays with a Component (YPbPr) Input
1) Press the Menu button on the front panel of the Master Three once. You should see
2) ‘Main Menu / Input Select’ on the FPD.
3) Press the Up button once. You should see ‘Main Menu / Output Setup’ on the FPD.
4) Press the Enter button. You should see ‘Output Setup / Analog/Digital’ on the FPD.
5) Press the Enter button. You should see ‘Analog/Digital / BNC (Analog)’. If you don’t, press the Up button once
and the press Enter. You should see ‘Output Setup / Analog/Digital’ on the FPD.
6) Press the Down button four times. You should see ‘Output Setup / Color Space’ on the FPD.
7) Press the Enter button once. You should see ‘Color Space / YPbPr’ on the FPD. If you don’t, press the Up but-
ton once and press Enter. You should see the Master Three’s on screen Display (OSD) on your screen.
The Master Three cannot output a component signal if the input signal is from a DVI or HDMI source with
HDCP. Instead the Master Three outputs a blue screen. 
						

							3.0  SETUP
R599751 - Master Three User Manual 13 
Displays with a VGA HD-15 (Computer) or 5BNC RGBHV input
1) Press the Menu button on the front panel of the Master Three once. You should see ‘Main Menu / Input Select’
on the FPD.
2) Press the Up button once. You should see ‘Main Menu / Output Setup’ on the FPD.
3) Press the Enter button. You should see ‘Output Setup / Analog/Digital’ on the FPD.
4) Press the Enter button. You should see ‘Analog/Digital / BNC (Analog)’. If you don’t, press the Up button once
and then press Enter. You should see ‘Output Setup / Analog/Digital’ on the FPD.
5) Press the Down button four times. You should see ‘Output Setup / Color Space’ on the FPD.
6) Press the Enter button once. You should see ‘Color Space / RGB’ on the FPD. If you don’t, press the Up button
once and press Enter. You should see the Master Three’s on screen Display (OSD) on your screen.
STEP 3 - Connecting your Sources to the Master Three
Up to 12 video sources can connected to the Master Three. Use the following suggestions for connections to
several popular video sources.
VCR/LD Player/DVR
The Master Three cannot output an RGBHV signal if the input signal is from a DVI or HDMI source with
HDCP. Instead the Master Three outputs a blue screen.
Some VCRs and LD players have S-Video outputs. These give an improved picture from these sources. If
your LD player or DVR has a digital audio output, CineVERSUM recommends you use that connection..
HDMIINPUT
1234
INPUT OUTPUT1
32
4
DIGITAL AUDIO SERIAL PORTANALOG AUDIO INPUT
Y (G) Pb  (B) Pr  (R) H VDC In+6V @5A
POWER
Y (G) Pb (B)Pr  (R)1
21
21
21
2
S-VIDEO VIDEO COMPONENTLR
ANALOG VIDEO OUTPUTSDI
INPUT
I
N
P
U
T
S
SYNC
I
N
P
U
T
O
U
T
P
U
T
12:00
VIDEO
AUDIO
L
R
IN OUT
S-Video
Composite
Video
L- A nalog
Audio
R-Analog
Audio
VCR/LD Player/DVR 
						

							3.0  SETUP
14 R599751 - Master Three User Manual
DVD Player/DVD Recorder
 Note:
If you have a display with an HDMI/DVI input, CineVERSUM recommends you use the DVI/HDMI output of your
DVD player with the player’s output resolution set to the lowest output resolution (preferably 480i). If you have a
display with only component or RGBHV inputs, use either an SDI or component video connection. SDI outputs
typically need to be added to your DVD player. This gives the additional benefit of skipping an extra digital-to-analog
(D-to-A) and analog-to-digital (A-to-D) step for a picture with even more detail then a component connection. With a
component connection, set the player’s output to 480i, minimizing the amount of processing done in the player.
DVI-D OUT (HDCP)
HDMI OUT
OPTICALCOAXIAL
HDMI
HDMI
SDI OUT
HDMIINPUT
1234
INPUT OUTPUT1
32
4
DIGITAL AUDIOSERIAL PORT
ANALOG AUDIO INPUT
Y (G) Pb  (B) Pr  (R) H VDC In+6V @5A
POWER
Y (G) Pb(B) Pr (R)
1
21
21
21
2
S-VIDEO VIDEO COMPONENTL
R
ANALOG VIDEO OUTPUTSDIINPUTI
N
P
U
T
SSYNC I
N
P
U
T
O
U
T
P
UT
DVI-D
DVI -HDMI
HDMI Optical
AudioCoaxialAudioSDI
COMPONENT OUT
Component
DVD Player/ DVD Recorder 
						

							3.0  SETUP
R599751 - Master Three User Manual 15 
High-Definition Set Top Box or DVR/D-VHS
 Note:
Some set top boxes require you to switch the output resolution. This means that if you are watching an HD channel
you must manually switch the output resolution to 720p/1080i/p, or if you are watching an SD channel, you must
manually switch the output resolution to 480i or 480p, 480i preferably. If your display only has component or RGBHV
inputs, use the component output from your HD source.
  
COMPONENT OUT
High-Definition Set Top Box or DVR/D-VHS 
						

							3.0  SETUP
16 R599751 - Master Three User Manual
Game Console
Personal Computer
 Set the game console to output the highest resolution available to get the best results.
Only VGA (640x480), SVGA (800x600), XGA (1024x768), and SXGA (1280x1024) resolutions are
supported at 60 Hz.
HDMIINPUT
1234
INPUT OUTPUT1
32
4
DIGITAL AUDIO SERIAL PORTANALOG AUDIO INPUTY (G)Pb (B)Pr (R)HVDC In+6V @5A
POWER
Y (G)Pb(B)Pr (R)1
21
21
212
S-VIDEO VIDEO COMPONENTL
R
ANALOG VIDEO OUTPUTSDIINPUTI
N
P
U
TSSYNC I
N
P
U
T
O
U
T
P
UT
Proprietary
HDTV
AV PackOptical
Audio
Component
Game Console
HDMIINPUT
1234
INPUT OUTPUT1
32
4
DIGITAL AUDIO SERIAL PORTANALOG AUDIO INPUTY (G)Pb (B)Pr (R)HVDC In+6V @5APOWER
Y (G)Pb(B)Pr (R)1
21
21
21
2
S-VIDEO VIDEO COMPONENTLR
ANALOG VIDEO OUTPUTSDI
INPUT
I
N
P
U
T
S
SYNC
I
N
P
U
T
O
U
T
P
U
T
DVI-DDVI-D
DVI-
HDMI
RGBHVOptical
AudioCoaxial
Audio
Personal Computer 
						

							3.0  SETUP
R599751 - Master Three User Manual 17 
3.2 Audio Operation
The Master Three features an audio delay function to exactly match the video delay incurred by the video
processing. It accepts four discrete digital audio inputs: two coaxial (Audio 1, 2) and two optical (Audio 3 and 4), one
analog audio input and four HDMI audio inputs.
The locations of the audio inputs are shown on the back panel diagrams earlier in this product guide.
The factory default audio assignment is as follows:
•Audio 1 (optical): none
•Audio 2 (optical): none
•Audio 3 (coaxial): none
•Audio 4 (coaxial): none
•Stereo (analog): none 
 Note:
The HDMI audio inputs can only be assigned to the same HDMI video input although any of the other audio inputs
can be assigned to any of the HDMI video inputs.You can assign a Digital Audio input to each Video input in the
following manner:
You can assign an audio input to each Video input in the following manner:
1) Select a video input on the remote control.
2) Select Audio 1, 2, 3, 4, Stereo, HDMI or Off from the ‘Input Adjust/Audio Input’ menu.
If an analog video input is selected, the HDMI option will not be available. 
						

							4.0  MENU OPTIONS
18 R599751 - Master Three User Manual
4.0 MENU OPTIONS
4.1 Input Select
There are twelve available inputs on the Master Three:
•VIDEO 1 Video 1 (Composite)
•VIDEO 2 Video 2 (Composite)
•S-VIDEO 1 S-Video 1
•S-VIDEO 2 S-Video 2
•COMPONENT 1 Component/RGBs 1
•COMPONENT 2 Component/RGBs 2
•RGBHV RGBHV/Component
•HDMI 1 HDMI 1
•HDMI 2 HDMI 2
•HDMI 3 HDMI 3
•HDMI 4 HDMI 4
•AUTO Automatic active input detection and selection
•SDI SD-SDI (SDI Video Input Module required)
These inputs can be accessed in five different ways:
•Using the front panel using the Left and Right buttons
•Using the remote control with the direct access buttons
•Using a universal remote programmed with the discrete codes
•Using the OSD from the front panel or from the remote to access the Input Select menu
•Using RS232 Serial Automation Protocol described in the appendix.
4.2 Input Aspect Ratio Control
The Input Aspect Ratio control selects the aspect ratio for the current input signal. The Master Three automatically
converts from the selected input aspect ratio to the selected output aspect ratio.
Push the Aspect button once to show the current input aspect ratio control function. To cycle through the available
functions, push the Aspect button repeatedly.
For the Input AR function, push the Up or Down button once to show the current setting. Push either of these
buttons again to cycle through the available aspect ratios. Push the Exit button to exit the menu and go back to the
Input Aspect Ratio selection.
For the Zoom, Pan and Borders functions, push the Up or Down button to select the two control settings available:
horizontal and vertical. Push the Enter button to adjust each setting.
•Push Up and Down to increase or decrease the setting.
•Push Exit again to exit this mode.
Video input signals are usually classified in the following two ways:
•Frame Aspect Ratio
•Active Input Aspect Ratio
Note:
The Zoom and Pan functions are applied to the input signal, not the output. This is an important consideration,
especially for the Pan function. For example: If you do not zoom a full frame image more than 100%, there is nothing
to pan. However, if part of the image is not on the screen, then the Pan function will work.
The Master Three’s menu is exit automatically after 30 seconds of no user interaction. 
						

							4.0  MENU OPTIONS
R599751 - Master Three User Manual 19 
Frame Aspect Ratio
Frame Aspect Ratio (FAR) consists of two possible ratios: 4:3 or 16:9. DVD discs encoded in a 16:9 frame are
sometimes referred to as anamorphic or enhanced for widescreen TV’s. For example, a non-anamorphic
widescreen DVD has a FAR of 4:3.
Active Aspect Ratio
Active Aspect Ratio (AAR) is the aspect ratio of the image or content (movie). This content is typically stated on the
back cover of DVD discs. Some common active aspect ratios are as follows:
•1.33:1 (4:3)
•1.55:1
•1.66:1
•1.78:1 (16:9)
•1.85:1
•2.35:1 (Cinemascope)
To use aspect ratio’s in addition to these, the Master Three provides the option to choose a custom aspect ratio
called User with a range of 1.01:1-3.00:1.
Master Three Image Mapping
The situation when the Frame Aspect Ratio (FAR) is the same as the Active Aspect Ratio (AAR) is sometimes
called Full Frame. This situation is illustrated below.
The Master Three maps the AAR to the Output Aspect Ratio (OAR) in the following three ways:
•When the AAR is greater than OAR, the Master Three puts up Borders at the top and bottom as shown below:
•When the AAR is less than the OAR, the Master Three puts up Borders on the left and right as shown below:
Borders Active Input Area
Borders Active Input
Area 
						

							4.0  MENU OPTIONS
20 R599751 - Master Three User Manual
•When the AAR is equal to the OAR (Output Aspect Ratio), the Master Three supplies no border as shown below.
Panorama
The Panorama feature is a non-linear stretch that can be applied only to a 4:3 video source. The panorama
stretches the picture with minimal perceptual distortion in the center of the screen. This mode can be turned ‘On’ or
‘Off’. Additionally this feature can be accessed in the IAR presets and it is titled ‘4:3 Stretch’.
Zoom
The Zoom function zooms in on or magnifies the image on your display. The minimum zoom is 100%, (no zooming);
the maximum zoom is 150% (zoom magnification factor of 1.5X).
•Horizontal Zoom Control: Push the Enter button to show the current Zoom setting. Push the Up and Down
button to increase or decrease the zooming factor.
•Vertical Zoom Control: Push the Enter button to show the current Zoom setting. Push the Up and Down button to
increase or decrease the zooming factor.
Pan
The Pan function allows the image to be shifted up, down, left and right. Note that the Pan function can only be used
after the image has been zoomed to any value greater than 100%.
•Horizontal Pan Control: Push the Enter button to show the current Pan setting. Push the Up button to pan to the
right. Push the Down button to pan to the left.
•Vertical Pan Control: Push the Enter button to show the current Pan setting. Push the Up button to pan up. Push
the Down button to pan the image down.
Borders
The Borders function allows you to add horizontal and/or vertical borders around the image. These borders obscure
part of the input image. Certain input-to-output aspect ratios already result in left/right or top/bottom border being
added. This control allows the system-generated borders to be extended, or for borders to be added when none
exist. As the borders are adjusted (see below) theMaster Three temporarily increases the gray level of the borders
so that they are visible during the adjustment process. The level will return to normal after the adjustment has
ceased.
•Horizontal Border Control: Push the Up button to move the left and right borders towards the middle of the
image, increasing the border width and cutting off the sides of the input image. Push the Down button to move
the left and right borders away from the image and decreases their width. If there are system-generated left/right
borders already present (for example, when the input aspect ratio is 4:3 and the output aspect ratio is 16:9), the
border width cannot be decreased beyond the base width created by the aspect ratio conversion.
•Vertical Border Control: Push the Up button to move the top and bottom borders towards the middle of the
image, increasing the border height and cutting off the sides of the input image. Push the Down button to move
the top and bottom borders away from the image and decrease their height. If there are system-generated top/
bottom borders already present (for example, when the input aspect ratio is 16:9 and the output aspect ratio is
4:3), the border height cannot be decreased beyond the base height created by the aspect ratio conversion.
Borders are automatically added by the system when the Active Input Aspect Ratio is not the same as the Output
Aspect Ratio as explained earlier in this guide. However you can add more borders using the Borders menu.
Presets
You can specify the Input Aspect Ratio by using the Presets or Manually.