Christie Projector Mirage S+14k User Manual

MAINTENANCE 
  Roadster / Mirage S+ User’s Manual 4-9 
 WARNING   
Unplug the projector. 
 
Figure 4.8. Lens Assembly  
Install the lens cap and press the lens release button 
See Figure 4.9. 
 
Figure 4.9. Depressing Lens Release 
Rotate the lens  
Rotate the lens counter-clockwise 
until the tabs are free from the lens 
retainer ring. 
See Figure 4.10A. 
NOTE: The connector slide assembly 
allows the connector to move as the 
lens is rotated. 
Pull lens out 
Lens connectors will disconnect when 
you...

MAINTENANCE 
4-10 
Roadster / Mirage S+ User’s Manual 
Insert new lens. 
Note: Remove small rear cap! Keep front cap on. 
• Electrical connector: Line up male connector on the lens with the female 
connector on the connector slide assembly. 
• Insert lens: Align the tabs on the lens plate lock  with the slots in the lens 
retainer ring. Push the lens in approximately ½ inch. 
• Rotate the lens: Rotate the lens clockwise until the tabs are tightly secured 
and the lens release button CLICKS. 
Power Up...

Section 5 
Troubleshooting 
 
 Roadster / Mirage S+ User’s Manual 5-1   
If the projector does not appear to be operating properly, note the symptoms present 
and use the following guide to assist you. If you cannot resolve the problems 
yourself, contact your dealer for assistance. 
NOTE: A qualified service technician
 is required when opening the projector to 
diagnose any “probable cause”. 
 
 
 
Blank screen, no display of image… 
1.  Confirm all power connections are still OK. 
2.  Make sure the...

TROUBLESHOOTING 
5-2 
Roadster / Mirage S+ User’s Manual 
The display is jittery or unstable… 
1.  If the display is jittery or blinking erratically, ensure that the source is properly 
connected and of adequate quality for detection. With a poor quality or 
improperly connected source, the projector will repeatedly attempt to display an 
image, however briefly. 
2.  The horizontal or vertical scan frequency of the input signal may be out of range 
for the projector. Refer to Section 6, Specifications...

 TROUBLESHOOTING 
  Roadster / Mirage S+ User’s Manual 5-3 
Values in Color Saturation slidebars vary over time 
1. Once defined, Color Saturation slidebar values fluctuate over time and will likely 
be different upon subsequent visits to this menu. This is normal and should be 
ignored, as these changes do not redefine the x/y coordinates or color gamut. 
The display is not rectangular… 
1.  Check leveling of the projector. Make sure that the lens surface and screen are 
as parallel to each other as...

TROUBLESHOOTING 
5-4 
Roadster / Mirage S+ User’s Manual 
Make sure the Ethernet settings are valid for your site—all network devices should 
have the same subnet mask and unique IP addresses. Make sure the projector is 
connected to a network before you attempt to change its IP address, and always cycle 
power (off-on) to implement the new IP address. 
1.  Make sure to save any address change, and re-boot to implement.  
If you still have trouble establishing communications with a projector added to an...

Section 6 
Specifications 
 
 Roadster / Mirage S+ User’s Manual 6-1 
NOTE: 1) Due to continuing research, specifications are subject to change without 
notice. 2) 3D available in Mirage S+ series only. 
Panel Resolution and Refresh Rate 
Pixel format (H x V) on 3 DMDs  1400 x 1050 
Refresh rate 
• Roadster S+12K/S+16K 
• Mirage S+14K  
23.97 – 92 Hz 
92 – 115 Hz 
 
Brightness 
ANSI 9 point measurement, with fully open optical aperture 
• Roadster S+ 12K 
• Roadster S+ 16K / Mirage S+14K 12,000 ANSI...

SPECIFICATIONS 
6-2 
Roadster / Mirage S+ User’s Manual 
 
Lens Offsets 
 
• Maximum offsets are reduced when simultaneously offsetting horizontally and vertically. All measurements are 
performed from the optical center ±7%
.  
 
Number of inputs 
Roadster S+12/S+16 
 
 
Mirage S+14K 
  
5 standard inputs including a Dual 
SD/HD-SDI 
1 input module slot 
4 standard inputs 
2 input module slots 
 
Analog: RGB / YPbPr 
(5 BNCs at INPUT 1) 
Signal types / color spaces                           o RGB  
o...

 TROUBLESHOOTING 
  Roadster / Mirage S+ User’s Manual 6-3 
Analog: Video (INPUTS 3 and 4) 
Signal formats  Composite-video (CVBS), S-Video (Y/C) 
Connectors 
 Composite Video 
(INPUT 3) 
 S-Video (INPUT 4)  
Female RCA
✽, gold plating TBD 
4-pin miniature DIN 
Video standards  NTSC, NTSC 4.43, PAL, PAL-M, 
PAL-N, PAL-60 & SECAM 
A/D conversion resolution  8-bit 
Input levels 
   Composite 
    S-Video, Luma (Y) 
    S-Video, Chroma ©  
1.0 V
p-p  ± 3dB (including sync tip) 
1.0 Vp-p  ± 3dB (including...

SPECIFICATIONS 
6-4 
Roadster / Mirage S+ User’s Manual 
Wired Keypad (converted IR remote keypad) 
Connector type  3.5 mm phono jack 
Input levels   High = 2.2 V – 5.6 V (or open) 
 Low = -0.6V – 0.9V @ 1mA 
Voltage output  +5VDC ±5%  
Current output  100 mA nominal, 250 mA max. 
 
 
IR Remote Keypad 
Number of IR sensors on projector.  2 (front and rear) 
Wavelength of peak sensitivity  950 nm 
Modulation (carrier) frequency  36 kHz (nominal) 
Encoding method  bi-phase 
IR reception range  100 ft....