Christie Projector Mirage S+14k User Manual

OPERATION 
  Roadster / Mirage S+ User’s Manual 3-67 
Table 3.4. System Error Codes  
Code Description GENERAL 12  Software error. Contact dealer/factory. 13  CRC error in flash ROM. Download new software. 14  Engineering-only programming is complete. Call Christie, replace TIPM. 15  Attempting to download s/w code without being in boot mode 16  Invalid interrupt. Power off/on. If persists, contact dealer/factory. 17  User has forced system to stay in boot mode 18  Attempting to program boot mode without...

Section 4 
Maintenance 
 
 Roadster / Mirage S+ User’s Manual 4-1 
This projector is safety agency approved and is designed for safe and reliable 
operation. However, safe operation cannot be assured by design alone; installers, 
maintainers, and users must maintain a safe operating environment for the system. 
Please read through and understand the following warnings and guidelines promoting 
safe usage of the projector. 
 WARNING  
Always REMOVE the lens when shipping a projector. 
 WARNING  
Never...

MAINTENANCE 
4-2 
Roadster / Mirage S+ User’s Manual 
LAMP: Do not operate the Bubble lamp for more than the lamp’s warranty limit; risk 
of the lamp shattering increases as a result of changes in the quartz glass that occur 
with use. Operation beyond the lamp’s warranty limit also significantly reduces 
brightness output. 
 WARNING  
Never attempt to remove the lamp housing directly after use. 
The lamp is under great pressure when hot and may explode, 
causing personal injury and/or property damage....

MAINTENANCE 
  Roadster / Mirage S+ User’s Manual 4-3 
Slots and openings in the projector provide ventilation. To ensure reliable operation 
of the projector and to prevent overheating, these openings must never be blocked or 
covered. The projector should never be placed near or over a radiator or heat register. 
The projector should not be placed in an enclosure unless proper ventilation is 
provided. For best results, ensure that the projector bottom is above any “lip” that 
may be present on a...

MAINTENANCE 
4-4 
Roadster / Mirage S+ User’s Manual 
 
The IR Remote Keypad uses two AA size, 1.5V batteries (preferably alkaline). To 
install new batteries, 1) open the battery compartment at the back side of the keypad 
by placing your thumb in the oval depression and sliding the cover out about ½ inch. 
See Figure 4.1. 
Remove the old batteries 
and properly discard. Wait 
a minute or two, and 2) 
place the new batteries in 
the compartment, orienting 
the positive/negative of 
each battery...

MAINTENANCE 
  Roadster / Mirage S+ User’s Manual 4-5 
 WARNING  
Lamp replacement is to be done by 
a qualified service technician only. 
 WARNING  
Never attempt to remove a hot lamp. A hot lamp is under great 
pressure and may explode, causing personal injury and/or 
property damage. Allow to cool completely and handle by the 
housing only. 
 WARNING  
Make sure to use the correct wattage lamp supplied by Christie. 
Turn the projector off  
Allow the cooling fans to stop automatically before...

MAINTENANCE 
4-6 
Roadster / Mirage S+ User’s Manual 
 
Figure 4.3. Remove Retaining Bar 
Remove the lamp module. 
See Figure 4.4. Firmly grasp the handle and pull the lamp module straight out of the 
projector. 
 
Figure 4.4. Remove Lamp Module 
Insert the new lamp module 
Align the base plate of the new lamp 
module under both side alignment guides 
(see right). Slide the module fully into the 
projector. Push with normal force until the 
resistance increases, then firmly
 push 
module another ½ inch....

MAINTENANCE 
  Roadster / Mirage S+ User’s Manual 4-7 
Re-install retaining bar 
Note: Correct positioning of the lamp module is essential. Ensure that the retainer 
bar is in place and secure screws in the order described below. 
See Figure 4.5. Position the retaining bar along the bottom edge of the lamp module, 
with ends under alignment guides. If the bar does not fit, push the lamp module 
further in. 
 IMPORTANT  
The tightening order of the screws is 
critical for proper lamp contact
 and...

MAINTENANCE 
4-8 
Roadster / Mirage S+ User’s Manual 
Replace the air filter when the lamp module is replaced, or more frequently if 
operating the projector in a dusty environment. The filter is located adjacent to the 
lens. 
Turn off the projector, cool, and unplug 
Before removing or installing a filter, turn off the projector and allow it to cool for 
five minutes before unplugging. Make sure the lens cap is on. 
 WARNING  
 Unplug the projector 
Remove filter door 
See Figure 4.6. Loosen the screw...