Christie Projector Mirage 4K35 User Manual

							   Specification
Mirage 4K35 User Manual91
020-101377-03 Rev. 1 (07-2015)
Optional input cards
To determine which SDI signal types are officially supported, see  Mirage signal connectivity on page 
88.
Control signal compatibility
Input cardPart numberAdditional information
Dual 3G SD/HD-SDI 108-313101-02+
Dual Link DVI (DDIC) 108-312101-02+ Analog signals  are not supported for this input card; therefore 
VGA port and VGA to DVI co nverters are not supported.
Twin HDMI (THIC) 108-311101-XX
Twin DisplayPort (TDPIC) 108-451101-XX
Ethernet port
Interface 10Base-T/100Base-TX
Connector Female RJ-45
USB
Connector Type B
Interface USB to serial (bit rate identical to RS232)
3D Sync
Connector BNC Male
Interface TTL inputs and outputs
RS422
Connector 9-pin subminiature D, female
Bit rate 115,200 bps
Data format 1 start bit, 8 data bits, 1 stop bit, no parity
RS232 IN
Connector 9-pin subminiature D, female
Bit rate 115,200 bps
Data format 1 start bit, 8 data bits, 1 stop bit, no parity 
						

							   Specification
Mirage 4K35 User Manual92
020-101377-03 Rev. 1 (07-2015)
Temperature sensor thresholds
The projector shutdowns within one minute of an error threshold being reached.
RS232 OUT
Connector 9-pin subminiature D, male
Bit rate 115,200 bps
Data format 1 start bit, 8 data bits, 1 stop bit, no parity
Lamp power supply (LPS)
Control port
Interface RS232
Connector at lamp power supply  end9-pin subminiature D, male
Interlock port
Interface +5V TTL-compatible, opto-isolated at LPS end
Connector at lamp power supply en d9-pin subminiature D, female
Number and type of signals 1 - lamp enable (low = enable lamp)
3 - safety interlock (high = disable lamp)
1 - +5V to power opto-isolation interface
LocationWarning 
( °C)Error 
( °C)Remarks
Integrator rod 110 120
Prism 65 75
Air intake 47 52
Lamp exhaust 100 N/A
MCPU 75 95
ABP 82 95
HIP scaler 82 95
HIP warp red 82 95
HIP warp green 82 95
HIP warp blue 82 95
Formatter red 82 95
DMD red 65 70
Formatter green 82 95 
						

							   Specification
Mirage 4K35 User Manual93
020-101377-03 Rev. 1 (07-2015)
Warning thresholds for fans
All fan warnings are set to ~75% of their normal operating speeds.
DMD green 6570
Formatter blue 82 95
DMD blue 6570
Option card 1 8095
Option card 2 8095
Option card 3 8095
Option card 4 8095
EVB 80 95
Lens MCB 7595 v1.0x software only; removed in v1.1.0+ software
Lamp MCB 9095 v1.0x software only; removed in v1.1.0+ software
LocationWarning RPM
Light engine intake (fan 5) 3300
Light engine intake (fan 6) 3300
Light engine intake (fan 8) 3300
Formatter—green blower (fan 7) 3500
Laminar airflow device (fan 4) 5900
Electronics intake (fan 10) 5700
Electronics intake (fan 11) 5700
Electronics intake (fan 12) 5700
Image processor warp blower (fan 9) 2400
Electronics exhaust (fan 1) 3400
Electronics exhaust (fan 2) 3400
Liquid cooling radiator (fan 3) 1800
Image processor scaler (fan 13) 5100
LocationWarning 
(°C)Error 
( °C)Remarks 
						

							   Specification
Mirage 4K35 User Manual94
020-101377-03 Rev. 1 (07-2015)
Warning threshold for liquid cooling module
Touch panel controller
Power requirements
LocationWarning
Flow meter 0.2mL/min
Liquid cooling pump 180 RPM
TPC 650H
Type of display Color VGA TFT LCD, backlit
Display size 144.8 mm (5.7 inches) diagonal
Display resolution (H x V pixels) 640 x 480
Maximum dimensions (W x H x D) 195 mm x 148 mm x 58 mm
Integrated operating system Microsoft Windows® XPe
Communication interface with projector 10/100/1000 BaseT Ethernet
Power requirement 0.71A maximum at 24VDC ± 10%
Interface connector 12-pin circular connector (push-pull)
Projection Head
AC Input
Rated input voltage 200 - 240 VAC
Rated line frequency 50 - 60 Hz nominal
Inrush current 70 A maximum
Current consumption 6 A maximum (at 200 VAC)
Power consumption 1200 W maximum
Current rating of AC input 10-15 A maximum (specified wall breaker)
Lamp (DC)
Operating voltage range 18 - 46 VDC
Start-up voltage (open current) 135-175 VDC
Operating current range 50-180 A
Connector type Field wireable lugs 
						

							   Specification
Mirage 4K35 User Manual95
020-101377-03 Rev. 1 (07-2015)
Power requirements
7kW Lamp Power Supply
Nominal voltage range Low line: 200 - 230 VAC
High line: 380 - 415 VAC
Operating voltage range Low line: 180 - 253 VAC
High line: 342 - 456 VAC
Number of phases 3
Line frequency 50 - 60 Hz nominal
Inrush current 120 A maximum
Current per phase Low line: 35 A maximum
High line: 26 A maximum
Power Consumption 8.8 kW max. (at max. output for 6kW lamp plus head)
Current rating of 3phase AC input 37A
Lamp power supply output to projection head
Operating voltage range18 - 46 VDC
Start-up voltage (open current) 125 - 155 VDC
Operating current range 50 - 180 A
Ripple 1% max (at 25°C, rated input and rated output)
Connector type Field wireable lugs
Lamp power supply power receptacle output
Operating voltage range 200 - 230 VAC
Operating current range—projection head 6 A
Operating current range—heat extractor 1 A
Current rating of input Both run from 15 A breaker (internal)
Projection Head
AC Input
Rated input voltage 200 - 240 VAC
Rated line frequency 50 - 60 Hz nominal
Inrush current 70 A maximum
Current consumption 6 A maximum (at 200 VAC) 
						

							   Specification
Mirage 4K35 User Manual96
020-101377-03 Rev. 1 (07-2015)
Power consumption 1200 W maximum
Current rating of AC input 10-15 A maximum (specified wall breaker)
Lamp (DC)
Operating voltage range 18 - 46 VDC
Start-up voltage (open current) 135-175 VDC
Operating current range 50-180 A
Connector type Field wireable lugs
7kW Lamp Power Supply
Nominal voltage range Low line: 200 - 230 VAC
High line: 380 - 415 VAC
Operating voltage range Low line: 180 - 253 VAC
High line: 342 - 456 VAC
Number of phases 3
Line frequency 50 - 60 Hz nominal
Inrush current 120 A maximum
Current per phase Low line: 35 A maximum
High line: 26 A maximum
Power Consumption 8.8 kW max. (at max. output for 6kW lamp plus head)
Current rating of 3phase AC input 37A
Lamp power supply output to projection head
Operating voltage range18 - 46 VDC
Start-up voltage (open current) 125 - 155 VDC
Operating current range 50 - 180 A
Ripple 1% max (at 25°C, rated input and rated output)
Connector type Field wireable lugs
Lamp power supply power receptacle output
Operating voltage range 200 - 230 VAC
Operating current range—projection head 6 A
Operating current range—heat extractor 1 A
Current rating of input Both run from 15 A breaker (internal)
Projection Head 
						

							   Specification
Mirage 4K35 User Manual97
020-101377-03 Rev. 1 (07-2015)
Lamp
Physical specifications
7kW Lamp Power Supply
Type Xenon bubble
CDXL-20 1000W min., 2000W nom., 2200W max.
CDXL-20SP 1400W - 2000W
CDXL-30 2000W min., 3000W nom., 3300W max.
CDXL-30SP 2100W - 3000W
CDXL-45 2300W min., 4500W nom., 4950W max.
CDXL-60 2750W min., 6000W nom., 6600W max.
NOTE:  The lamp power supply is current regulated to  a maximum of 180 A. Therefore the maximum power 
specification for a given lamp may not be  achievable until the lamp has aged, as lamp voltage increases with hours 
of use. The maximum power of the lamp po wer supply is restricted to 7000W ± 100W.
Average life
CDXL-20 2400  hours
CDXL-20SP 3200 hours
CDXL-30 1500 hours
CDXL-30SP 1900 hours
CDXL-45 1000 hours
CDXL-60 600 hours
Wait time between lamp strikes 2 minutes minimum
NOTE:  Projectors typically force a 10 minute cool down peri od. Make sure not to re-strike the lamp any sooner 
than two minutes into this co ol down period since hot re-strikes reduce lamp life.
Overall size (L x W x H)
(including lens mount and feet) 1298 x 648 x 483 (mm)
51.1 x 25.5 x 19.0 (inches)
Projector head weight
Without lens mount cover 114 kg (251 lbs)
Shipping (includes pack aging) 146 kg (322 lbs)
Operating position
Rotation about projection axis +90 degrees maximum (lamp door down), -15 
degrees maximum 
						

							   Specification
Mirage 4K35 User Manual98
020-101377-03 Rev. 1 (07-2015)
Regulatory
This product conforms to the following regula tions related to product safety, environmental 
requirements and electrom agnetic compatibility (EMC).
Safety 
• CAN/CSA C22.2 No. 60950-1
• ANSI/UL 60950-1
• IEC 60950-1
• EN 60950-1
• IEC 62471-1 
Approvals 
This product is designed and built to comply with  all relevant directives, standards, safety, health 
and environmental rules and regulations required  for the product to be sold in: USA/Canada, EU, 
Norway, Australia/New Zealand, Kuwait, China, Ko rea, Japan, Mexico, Ukraine, Russia, India, 
Argentina, Brazil, Singapore, South Africa, and Saudi Arabia international  packaging recycling mark 
requirements.
• EU Directive (94/62/EC) on packaging and packaging waste;
• China packaging recycling mark standard (GB18455-2001).
Electro-magnetic compatibility
Emissions
FCC CFR47, Part 15, Subpart B, Class A
CAN ICES-3 (A) / NMB-3 (A)
CISPR 22/EN 55022, Class A• IEC 61000-3-2/EN61000-3-2
Immunity
CISPR 24/EN55024• IEC 61000-3-3/EN61000-3-3
Environmental
EU Directive (2011/65/EU) on the restriction of the  uses of certain hazardous substances (RoHS) in 
electrical and electronic equipment and the applicable official amendment(s)
EU Regulation (EC) No. 1907/2006 onthe registrati on, evaluation, authorization and restriction of 
chemicals (REACH) and the applicable official amendment(s).
Tilt of projection axis from  horizontal  ±15 degrees maximum 
						

							   Specification
Mirage 4K35 User Manual99
020-101377-03 Rev. 1 (07-2015)
EU Directive (2012/19/EU) on waste and electrical and electronic equipment (WEEE) and the 
applicable official amendment(s)
China Ministry of Information Industry Order No.39 (02/2006) on the control of pollution caused by 
electronic information products, hazardous substances concentration limits (SJ/T11363-2006), and 
the applicable product marking requirements (SJ/T11364-2006)
Environment
Accessories
Operating environment
Temperature 10 to 35°C (50 to 95°F)
Humidity (non-condensing) 20 to 80%
Altitude 0 to 3000 meters
Maximum ambient temperature 35°C
Non-operating environment
Temperature-25 to 65°C (-13 to 149°F)
Humidity (non-condensing) 0 to 95%
Standard (Included with product)
• Lens plug (required for shipping when lens is not installed to prevent contamination of critical optical 
components)
• Nylon safety strap with clip (required to secure  projector to tabletop or optional rack mount)
• Touch panel controller (TPC) with interface cable • Shroud
• Light engine removal tool • Convergence tool
• Warranty card • Web registration form
• Low security keys
(Included with Lamp Power Supply)
• 10’ Line Cord (250V/10A) • Harness package (includes 4 cables) 
						

							   Specification
Mirage 4K35 User Manual100
020-101377-03 Rev. 1 (07-2015)
Lenses (sold separately)
DescriptionPart number
Lens 0.72:1 113-104106-XX
Lens 0.9:1 38-809071-XX
Lens 1.13-1.31:1 129-104106-XX
Lens 1.31-1.63:1 129-105107-XX
Lens 1.63-2.17:1 129-106108-XX
Lens 1.98-2.71:1 129-107109-XX
Lens 2.71-3.89:1 129-108100-XX
Lens 3.89-5.43:1 129-109101-XX
Lens 5.0-7.69:1 129-110103-XX
Note:  The lens throw values in the lens name may differ from the actual throw ratios. For details, see the 4K 
Lens Throw Technical Reference (P/N: 020-100904-XX).
Replacement Lamps  (sold separately)
DescriptionPart number
CDXL-20 003-000598-02
CDXL-20SP 003-004251-01
CDXL-30 003-000599-02
CDXL-30SP 003-004252-01
CDXL-45 003-000600-02
CDXL-60 003-000601-02
Replacement air filters (sold separately)
DescriptionPart number
Light engine filter (five-pack) 003-001184-XX
Liquid cooling radiator filter 003-003082-XX
LAD filter (three-pack) 003-001982-51P