Christie Projector LWU701i User Manual

							40LWU701i/LW751i/LX801i/LWU601i/LW651i
User's Manual - Operating Guide020-000786-02
LIT MAN USR D2
Operating
Adjusting the projector’s elevator
Increasing or shortening the length of 
the elevator feet shifts the projection 
position and the projection angle.
Turn the elevator feet each to adjust 
their length.
►Do not lengthen the elevator feet exceeding 30 mm. The foot
lengthened exceeding the limit may come off and drop the projector down, and
result in an injury or damaging the projector.
►Do not place the projector with an inclination exceeding
5 degrees. The projector leaned exceeding the limit could cause malfunction and 
shorten the life of the projector. CAUTION
5°
max. 30mm
WARNING
Installation angle
Vertical and horizontal direction 
in portrait mode
The projector may be installed at 
horizontal angle of ±10°.
The projector may be installed at 
vertical angle of ±10°.
• The lamp side of the 
projector must face upward for 
vertical installations.
• If Other Error has occurred, 
check the installation. Install the 
projector correctly and restart it.
• When using portrait mode, the 
service life of a lamp becomes 
shorter. NOTE
Lamp side
5 °
10°  10°
10°
10° 
						

							41LWU701i/LW751i/LX801i/LWU601i/LW651i
User's Manual - Operating Guide020-000786-02
LIT MAN USR D2
Operating
The ZOOM or FOCUS dialog appears when you 
press any of the buttons from ZOOM, ZOOM - , 
ZOOM + , FOCUS + and FOCUS -. 
1. Use the ZOOM + / - buttons on the remote 
control or ZOOM button and ◄/► cursor buttons 
on the projector to adjust the screen size.
2. Use the FOCUS  + / - buttons to focus the picture.
Adjusting the lens 
Adjusting the zoom and focus
• The projector may ignore the operation 
by other buttons while the lens is moving.NOTE
Press the LENS SHIFT  button. The LENS SHIFT 
dialog appears. Using the ▲/▼/◄/►buttons while the 
dialog is displayed shifts the lens. Generally, better 
image quality can be got when the lens is set to the 
center.
Press the LENS SHIFT  button again to exit the 
LENS SHIFT function.
CENTERING
Press the ENTER or INPUT button while the dialog is 
displayed to execute the CENTERING feature, which 
adjusts the lens to the center. A message dialog is dis-
played for confirmation. Pressing the ►button performs 
CENTERING. You can also perform CENTERING in the 
standby mode by pressing the  FUNCTION and LENS 
SHIFT buttons on the control panel for three seconds at 
the same time.
Adjusting the lens position
►Do not put your fingers or any other things around the lens. The 
moving lens could catch them in the space around the lens and result in an injury.CAUTION
• While the lens is moving to the center, the menu disappears and an 
hourglass icon appears on the screen. CENTERING may take some time till the 
lens reaches the center.
• The projector may ignore operation by buttons while moving the lens.
• 
The CENTERING feature while the projector is in the standby mode is disabled if the 
STANDBY MODE item of SETUP menu is set to POWER SAVE. Perform CENTERING 
before the projector's power is turned off, or set the STANDBY MODE to NORMAL.
• The adjustable range of LENS SHIFT varies depending on the lens unit mounted 
on the projector to maintain picture quality. Therefore, LENS SHIFT adjustment may 
not reach the end of the indicator in the dialog. This is not a failure.
NOTE
FOCUS - / +  buttons
ZOOM button
FUNCTION 
button
LENS SHIFT  
button
SHUTTER
FOCUS + /  - buttons
LENS SHIFT  button
ZOOM +
 / - buttons 
						

							42LWU701i/LW751i/LX801i/LWU601i/LW651i
User's Manual - Operating Guide020-000786-02
LIT MAN USR D2
Operating
• The projector may ignore the operation by buttons while moving the lens.
• You can perform the LOAD function using  LENS MEMORY button.NOTE
Adjusting the lens (continued)
This projector is equipped with memory functions for the 
lens adjustments (ZOOM, FOCUS, LENS SHIFT and 
LENS TYPE). Up to three sets of adjustments can be 
stored.
To use the lens memory feature, press the 
LOAD or 
FUNCTION button while the LENS SHIFT dialog is dis-
played. Then the LENS MEMORY dialog appears. The 
current lens adjustments are displayed on the “CUR-
RENT” line. The adjustments already stored in the lens 
memory are displayed on the lines of SAVE and LOAD-
1 to 3.
Lens memor y
    SAVE:  
To store the current lens adjustments, select one of the 
"SAVE" options numbered 1 to 3 (number of the lens 
memory) and press the ►or ENTER button. 
Remember that the current data being stored 
of a memory is lost by saving new data into the 
memory.
    LOAD:  
To recall stored adjustments, select one of the 
"LOAD" options numbered 1 to 3 (number of the 
lens memory) and press the ►or 
ENTER button. 
Remember that the current adjusted condition is lost by loading data. If you want to 
keep the current adjustment, save it before performing a LOAD function.
    CLEAR LENS MEMORY:  
To clear the adjustment stored in a lens memory, select CLEAR LENS MEMORY 
and press the ►or ENTER button. The CLEAR LENS MEMORY dialog is displayed. 
Select the number of the lens memory to be cleared using the ▲/▼ buttons and 
press the ►button. A message dialog is displayed for confirmation. Press the 
►button again to clear the lens memory.
LENS MEMORY 
button
FUNCTION 
button
SHUTTER 
						

							43LWU701i/LW751i/LX801i/LWU601i/LW651i
User's Manual - Operating Guide020-000786-02
LIT MAN USR D2
Operating
1.Press AUTO button on the remote control.  
Pressing this button performs the following.
Using the automatic adjustment feature
   For a computer signal 
The vertical position, the horizontal position and the  
horizontal phase are automatically adjusted.  
Make sure that the application window is set to its  
maximum size prior to attempting to use this feature. A dark picture may still be 
incorrectly adjusted. Use a bright picture when adjusting.
   For a video signal 
The video format best suited for the respective input signal is selected 
automatically. This function is available only when the AUTO is selected for 
the VIDEO FORMAT item in the INPUT menu (
70). The vertical position and 
horizontal position are automatically set to the default.
   For a component video signal  
The vertical position and horizontal position are automatically set to the default. 
The horizontal phase is automatically adjusted.
AUTO 
button
• The automatic adjustment operation requires approximately 10 seconds. 
It may not function correctly with some input. 
• When this function is performed for a video signal, an extra line may appear 
outside a picture.
• When this function is performed for a computer signal, a black frame may be 
displayed on the edge of the screen, depending on the computer model. 
• 
The items adjusted by this function may vary when the FINE or DISABLE is selected 
for the AUTO ADJUST item of the SERVICE item in the OPTION menu (
93).
NOTE 
						

							44LWU701i/LW751i/LX801i/LWU601i/LW651i
User's Manual - Operating Guide020-000786-02
LIT MAN USR D2
Operating
KEYSTONE:  Adjust the vertical and horizontal 
keystone.
3D KEYSTONE:   
Adjust each of the screen corners and 
sides to correct the distortion.
WARPING:   Project an image on several types of 
screen.
• The menu or dialog automatically disappears after several seconds 
of inactivity. Press the GEOMETRY button again, or point the cursor at EXIT in 
the dialog and press the ►or  ENTER button to end the operation and close the 
menu or dialog.  NOTE
To correct the distortion of projected screen, you can select one of three 
options, KEYSTONE, 3D KEYSTONE, and WARPING. First press the 
GEOMETRY button to display the GEOMETRY CORRECTION menu, and 
point at one of the items with the ▲/▼ buttons.
Correcting the distortion 
Complete the following procedure for the item you selected. 
GEOMETRY 
button
Use Keystone/3D Keystone/Warping for adjustment. When one is selected, 
other items are not available.
    KEYSTONE: 
When KEYSTONE is pointed at, pressing the ► or 
ENTER button displays the KEYSTONE dialog.
1. 
Select the vertical or horizontal keystone ( / ) 
with the ▲/▼ buttons.
2. 
Use the ◄/► buttons to adjust the keystone distortion.
• When the zoom adjustment is set to the TELE (telephoto focus), 
this function may be excessive. This function should be used when the zoom 
adjustment is set to the full WIDE (wide-angle focus).
• When the horizontal lens shift is not set to the center, this function may not 
work correctly.
• Point at RETURN in the dialog with the ▲/▼ buttons and press ◄ or ENTER 
button to return to the KEYSTONE menu. NOTE 
						

							45LWU701i/LW751i/LX801i/LWU601i/LW651i
User's Manual - Operating Guide020-000786-02
LIT MAN USR D2
Operating
    3D KEYSTONE: 
When 3D KEYSTONE is pointed at, pressing the 
► or ENTER button displays the 3D KEYSTONE 
dialog. This projector is equipped with a test pattern for 
3D KEYSTONE. Select TEST PATTERNS with 
the 
▲/▼ buttons, then press the ◄/► buttons to 
switch on and off.
1.  Select SETUP with the ▲/▼ buttons and  
 press the 
► or ENTER button.
2.  Select one of the corners or sides to be adjusted 
 with the ▲/▼/◄/► buttons and press the 
ENTER or INPUT button.
3. Adjust the selected part as below. 
●  To adjust a corner, use the ▲/▼/◄/► buttons to adjust the position of the  corner.
●  To adjust the upper or lower side, use the ▲/▼ buttons to adjust the  distortion of the side.
●  To adjust the left or right side, use the ◄/► buttons to adjust the distortion  of the side.
●  To adjust another corner or side, press the  ENTER or INPUT button and 
follow the procedure from step 2.
Correcting the distortion (continued)
(continued on next page) 
						

							46LWU701i/LW751i/LX801i/LWU601i/LW651i
User's Manual - Operating Guide020-000786-02
LIT MAN USR D2
Operating
Correcting the distortion (continued)
4. This projector is equipped with a memory feature for 3D KEYSTONE 
adjustment. Up to three sets of adjustments can be stored.
●  SAVE:   To store the current 3D KEYSTONE adjustment, select one of the "SAVE" 
options numbered 1 to 3 (number of the memory) with the ▲/▼ buttons and 
press the ►, ENTER or INPUT button.  
The current data being stored is lost by saving new data.
●  LOAD:   To recall stored adjustments, select one of the "LOAD" options numbered 
1 to 3 (number of the memory) with the ▲/▼ buttons and press the ►, 
ENTER or INPUT button. 
The current adjusted condition is lost by loading data. If you want to keep 
the current adjustment, save it before performing a LOAD function.
• The LOAD functions whose linked memories have no data are skipped.
• There may be some noise and the screen may flicker for a moment when
loading data. This is not malfunction. NOTE
   WARPING: 
Projection on several types of screen can be performed by WARPING function. 
This function is operated by using dedicated PC tool, "Warping Tool". 
PC and projector are required to be connected with LAN cable to use this 
function. 
You can get the PC tool from the following URL.
http://www.christiedigital.com
Refer to Application Manual for operations. 
						

							47LWU701i/LW751i/LX801i/LWU601i/LW651i
User's Manual - Operating Guide020-000786-02
LIT MAN USR D2
Operating
Using the EDGE BLENDING features
1. Mode (Manual/Camera)
OFF: Disables the Blending function.
 Manual: Allows you to adjust Blending Region or Blending Level by using menu.
Camera:  Allows you to perform automatic adjustment by using Camera in Projector  Blending Tool.
• HDCR LiteLoc is not selectable when Blending is set to other than OFF.
• ECO MODE is not selectable when Blending is set to other than OFF.
•  Keystone/3D Keystone/Warping are not selectable when Camera is selected in 
Blending.
2. Blending Region2.1 Specifying Blending Region
Select one of the four sides with ▲/▼/
◄/► buttons and press ENTER or 
INPUT button. Blending Region can be specifi ed for left and right sides with 
◄/► buttons and for top and bottom sides with ▲/▼ buttons.
Specify Blending Region for each projector.
Adjust them referring to the guide displayed during the adjustment of Blending 
Region.
* The minimum value of Blending Region is 200 dots.
(continued on next page)
Guide line
Blend Region
Left ImageRight Image 
						

							48LWU701i/LW751i/LX801i/LWU601i/LW651i
User's Manual - Operating Guide020-000786-02
LIT MAN USR D2
Operating
(continued on next page)  3.1 Displaying Cropping Menu 
Select CROPPING with ▲/▼ buttons and press 
►, 
ENTER or INPUT button to display Cropping Menu. 
 
3.2 Setting Cropping 
Select MODE with ▲/▼ buttons and select ON with 
◄/► buttons. 
The input image is automatically cut out according 
to the settings of Blending Region.
3.  Cropping  When inputting the same image to each projector, The cropping function 
enables two projectors to cut out a part of input image and display one image 
on a large screen. The following patterns are supported.
1 x 22 x 2
2 x 1 
						

							49LWU701i/LW751i/LX801i/LWU601i/LW651i
User's Manual - Operating Guide020-000786-02
LIT MAN USR D2
Operating
 3.3 Adjusting Cropping Area
Adjust the Cropping Area when cutting out a part of input image.
Select SETUP with ▲/▼ buttons and press 
►, ENTER or INPUT button.
*  MODE is set to [OFF] temporarily and the guide of the Cropping Area  is displayed.
Select [LT]/[WH] with ▲/▼ buttons and press the  ENTER or INPUT button.
Move the guide display with ▲/▼/
◄/► buttons to select the region of the 
screen to be cut out.
Press the ENTER or INPUT button and then press 
◄ button to select SETUP, 
and MODE switches to ON automatically.
(continued on next page)  3.4 Adjust Cropping Area of the other projector.
Set the Cropping Area of the other projector with the same value as one 
projector.
The input image is automatically cut out according to the settings of the 
Blending Region.
*  To keep input image from not being seen while setting up, set BLANK to ON.
Input Image
Cropping
Input Image
Cropping