Christie Projector DWX555-GS User Manual

Section 3: INSTALLATION
GS Series User Manual020-000724-01 Rev. 1 (05-2014)3-13
3.7 Removing and Installing the Lens
When handling the projector after lens installation, make sure the front lens 
cap is placed on the lens to protect  the lens surface from potential damage. 
When carrying or moving the projector, do not handle by the lens. This may 
damage the lens, the cha ssis or other mechanical parts within the projector.
Installation Steps:
1.Center the lens:  Ensure that the lens is at or near its...

Section 3: INSTALLATION
GS Series User Manual020-000724-01 Rev. 1 (05-2014)3-14
3.8 Cable Cover Installation
1. Rotate the cable cover and insert the two guide pins into the guide holes.
2. Press and hold both lower corners of the cable cover while inserting the sheet clips into the projector casing.
Guide Pin
Guide Hole
Hold and Press Here 

Section 3: INSTALLATION
GS Series User Manual020-000724-01 Rev. 1 (05-2014)3-15
3.9 Portrait Cover Installation
1. Attach the Portrait cover to the left side of the projector and secure with the 6 step screws.
2. Mount the projector in an appropriate mounting kit, using the 4 mounting  points on the underside of the projector.
WARNING
•  Mount with the portrait cover side facing downwards.
•  The projector must not stand on a table top on the portrait cover
Tighten the six screws 

Section 3: INSTALLATION
GS Series User Manual020-000724-01 Rev. 1 (05-2014)3-16
3.10 Ceiling Mount Installation
Mount the projector with an appropriate mounting kit, using the 4 mounting 
points on the underside of the projector.
•  When not mounted properly, the projector may fall, causing hazards or  injury. The warranty on this projector does not cover any damage caused 
by the use of any non-recommended ceiling mount kit or installation of the 
ceiling mount kit in an improper location. 
•  Refer to...

Section 4: OPERATION
GS Series User Manual020-000724-01 Rev. 1 (05-2014)4-1
4. OPERATION
The projector has multilingual On-Screen Display (OSD) menus that allow you 
to make image adjustments and change a variety of settings.
•  Most of the projector controls are  accessed from within the projector menu 
system. There are several groups of related functions, with each group 
selectable from the Main menu as shown below. Press the MENU button on 
the remote control or on the built-in keypad on the rear of...

Section 4: OPERATION
GS Series User Manual020-000724-01 Rev. 1 (05-2014)4-2
4.1 Size and Position Menu
Size Presets
Display an image with the detected size, or resize the image by maximizing 
either the height, width or both, or resize to the maximum size possible while 
keeping the original aspect ratio.
•  Auto: Display with the detected size.
•  Native: Display in its native resolution.
•  4:3: Retain 4:3 aspect ratio.
•  Letterbox: Display with the bla ck borders on the top and bottom.
•  Full Size:...

Section 4: OPERATION
GS Series User Manual020-000724-01 Rev. 1 (05-2014)4-3
Pixel Phase
Analog RGB Signals only. Adjust pixel phase when the image still shows 
shimmer or noise after pixel tracking is optimized. Pixel phase can adjust the 
phase of the pixel-sampling clock relative to the incoming signal.
Horz Position
Move the image right or left within the area of available pixels.
Vert Position
Move the image up or down within the area of available pixels.
Digital Horz Zoom
Change the size of...

Section 4: OPERATION
GS Series User Manual020-000724-01 Rev. 1 (05-2014)4-4
•  Off: No Geometric correction is applied to the image.
•  Horz Keystone: Adjust the keystone horizontally and make a more square image. Horizontal keystone is used to correct a keystoned image shape in 
which the left and right borders of  the image are unequal in length, and the 
top and bottom are slanted to one of t he sides. This is intended for use with 
horizontally on-axis applications. For  horizontally offset...

Section 4: OPERATION
GS Series User Manual020-000724-01 Rev. 1 (05-2014)4-5
•  Pincushion/Barrel: Allow for correction for slight curved distortion from the lens or projection surface.
•  4-Corner: Allow the image to be squeezed to fit an area defined by moving  each of the four corners' x and y position.
•  Rotation: Allow an image to be rotated - most commonly to level the image.  While the image is rotated, the software  can crop any content that begins to 
fall off the panel. The function will...

Section 4: OPERATION
GS Series User Manual020-000724-01 Rev. 1 (05-2014)4-6
Auto Image
Force the projector to reacquire and lock to the input signal. This is useful 
when signal quality is marginal. Normal mode can support all of the 4:3 input 
sources.
Wide mode can support all of the 16:9 input source & most of the 4:3 input 
source. For those 4:3 input sources not recognized by Wide mode (example  
1400 x 1050), perform Auto Image using normal mode.